Installation Guide

ManualsBrandsSloan ManualsBathroom Sink FaucetsBASYS Polished Chrome Touchless Single Hole Bathroom Sink Faucet

INSTALLATION INSTRUCTIONS FOR ELECTRONIC

ACTIVE IR LAVATORY FAUCETS

Code No: 0816640

Rev. 7 (05/16)

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship

for a period of three (3) years (1 year for SF faucets, special finish and PWT electronics and 30 days on PWT software) from date of first purchase. During this period, Sloan Valve

Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole

and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be allowed for labor, transportation or other costs.

This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does

not cover the life of the battery.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE

FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

MODEL GUIDE OR BUILD YOUR FAUCET ONLINE AT WWW.SLOAN.COM

–––––

Body

Type

Power Crown . Mix Sensing Flow Rate . Batteries

Base

Plate*

Adapters

Drain

Pop-

0 – Hardwire Bowed . None Active IR

0.5 gpm (1.9 Lpm)

Multi-Lam

Spray Insert

. Alkaline None None No

1 – – – .

Below Deck

Mechanical

– – . – 4-inch* US Plug-in –

2 – – – .

Below Deck

Thermostatic

–

1.5 gpm (5.7 Lpm)

Aerated Insert

. – 8-inch* UK Plug-in –

Low,

Pedestal

– – . – –

1.5 gpm (5.7 Lpm)

Laminar Insert

. – – EU Plug-in –

4 – – – . – – – . – – Box Mount

5 – Battery Solar .

Integral

Side

Mixer

†

– – . – –

–

Low,

Integrated

Base

– - . - – – .

7 – Solar

Solar w/

LCD

. – – – . – – – –

EFX-6XX

Integrated Base,

Sensor Activated

Lavatory Faucets

EFX-3XX

Pedestal, Sensor

Activated Lavatory

Faucets

EFX __ __ __ . __ _0_ __ . _0 __ __ 0

BASYS

™

Any Application.

Any Environment.™

†

Integral Side Mixer not available on integrated base models.

* Base Plates are not intended for the integrated base models.

Summary of content (12 pages)

PAGE 1
BASYS ™ Any Application. Any Environment.™ Code No: 0816640 Rev. 7 (05/16) INSTALLATION INSTRUCTIONS FOR ELECTRONIC ACTIVE IR LAVATORY FAUCETS EFX-3XX EFX-6XX Pedestal, Sensor Activated Lavatory Faucets Integrated Base, Sensor Activated Lavatory Faucets MODEL GUIDE OR BUILD YOUR FAUCET ONLINE AT WWW.SLOAN.COM EFX __ __ __ . __ _0_ __ . _0 __ __ 0 ––––– Body Type Power Crown . Mix Sensing Flow Rate . Batteries Base Plate* Adapters Drain PopUp 0 – Hardwire Bowed .
PAGE 2
PRIOR TO INSTALLATION Base Plates When the BASYS™ Faucet is installed on a sink that has three (3) hole punchings, a base plate should be used. Base Plates should be Prior to installing the Sloan BASYS™ Series Faucets, install the items listed below. Also, refer to rough-in illustrations. IMPORTANT: specified at the time of ordering. • ALL PLUMBING SHOULD BE INSTALLED IN ACCORDANCE WITH APPLICABLE CODES AND REGULATIONS. • FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
PAGE 3
FAUCET ROUGH-IN 2” (51 mm) 6.25” (159 mm) 4” (106 mm) 5” (126 mm) 2” (47.5 mm) 42° 1.25” (31 mm) 2.5” (63 mm) 5.7” (147 mm) 2” 6” (51 mm) (152 mm) 4” (106 mm) 5” (124 mm) 2” 42° (46 mm) 1.25” (31 mm) 2.25” 2.
PAGE 4
1 - INSTALL FAUCET A Remove nut, faucet retainer and gasket. B Install Faucet with faucet retainer into the center hole in deck or lavatory — 1-3/16” (30 mm) min. hole required. NOTE: If installing the Faucet on a three (3) hole sink, a Base Plate should be installed at this time. NOTE: Do not remove label until water is connected. 2 - SECURE TO SINK DECK FAUCET D-SHAPED GASKET FAUCET RETAINER 13 mm NUT FLEX HOSE DO NOT PULL OR CRIMP AC POWER LINE.
PAGE 5
4 - START-UP SEQUENCE A For Hardwire Models, Plug Adapter B Remove label from sensor window. into receptacle. SENSOR LABEL ADAPTER TO FAUCET Electrical Connection for up to Six (6) Faucets Using One (1) Adapter C Activate faucet by holding installation instructions approximately 1-1/2” (38 mm) in front of sensor window until Red LED turns on then remove instructions while faucet sense its surroundings. Wait for green LED on side of faucet.
PAGE 6
ADDITIONAL FUNCTIONS Function Steps to Activate Function Default Setting IR Clic IR Activation Cover IR clic approximately for 2 sec. until LED will flash GREEN 1x - then remove finger from IR clic (Active for 5 sec.) –– –– Cleaning Mode IR Activation; Cover IR clic 2x - confirmation of the function is active by a couple flashes by the LED; to return to normal operation cover IR clic 1x or the faucet will automatically return to normal function after 2 min. 2 min.
PAGE 7
2x + SENSOR RANGE 1x 5ADJUSTMENT sec 2x + FACTORY SETTING IS APPROPRIATE FOR THE MAJORITY OF APPLICATIONS AND SHOULD NOT REQUIRE RESETTING 1x 5 sec UNLESS UNDER EXTREME SITUATIONS: HIGH REFLECTION OR LOW LIGHT. A IR Activation (see page 5).To enter programming mode place finger on IR clic for 2 times then remove. Light on side of crown should blink to indicate programming mode. B Cover IR clic until LED flashes Red 4 times-hold IR Clic until LED flashes 1 time to 8 times from minimum to maximum range.
PAGE 8
BATTERY REPLACEMENT NOTE: Replace Battery when LED1 indicator flashes red each time faucet is in use or when faucet stops functioning. LED1 is identified by the battery symbol. NOTE: Turning off water is not necessary. A Loosen cover screw and remove cover from battery pack. B Install four (4) AA-size batteries (supplied) as indicated by the (+) and (–) symbols inside the battery compartment. C Replace battery pack lid and tighten with screwdriver.
PAGE 9
REPLACE SPRAY INSERT NOTE: TURNING OFF WATER IS NOT NECESSARY, DUE TO INTEGRATED AUTOMATIC STOP VALVE. D Install new insert. A Remove crown by loosening hex screw located on underside NOTE: If changing to a different flow rate solenoid caddy must also be changed. of spout and slide crown down and lift off. NOTE: Screw is captive within faucet body. UNLOCK E Return spray removal tool to storage location. B Retrieve spray removal tool located near the spray insert.
PAGE 10
UPGRADE FAUCET FUNCTIONALITY B Place new crown on faucet by sliding onto spout and tightening hex A Remove crown by loosening hex screw located on underside of spout and slide crown down and lift off. NOTE: Screw is captive within faucet body. screw on underside of spout. NOTE: All electronics are fully encapsulated in the crown and thus protected from the environment and easy to replace or upgrade.
PAGE 11
TROUBLESHOOTING GUIDE 1. Red LED in spout does not blink 2 seconds after battery installation. Battery placement incorrect or batteries have been discharged. Ensure alkaline batteries are installed properly. Check the orientation of each battery matches the positive (+) and negative (-) symbols shown on the battery compartment. 5. Faucet delivers only a slow flow or dribble when sensor is activated. Water supply stop(s) are partially closed. Completely open water supply stop(s). 6.
PAGE 12
PARTS LIST Item # Part # 1A 1B 2 3A 3B 4 5 6A 6B 6C 7 8 9A 9B 10 11 12 13 14 15 16 17 18 Description 6C – – – EFX-1002-A Low Pedestal Faucet Assembly* Low Pedestal Faucet Assembly with Mixer* Low Integrated Base Faucet Assembly† 0.5 gpm/1.9 Lpm Multi-Lam insert (includes insert, o-ring, 2.5 mm allen key, and removal tool) EFX-1001-A 1.5 gpm/5.7 Lpm Aerated Stream Insert (includes insert, o-ring, 2.5 mm allen key, and removal tool) EFX-1000-A 1.5 gpm/5.