Installation Sheet

ADA Compliant
EAF-275 I.I. — Rev. 0a (03/05)
Code No. 0816490
INSTALLATION INSTRUCTIONS
SOLAR/BATTERY POWERED
SENSOR ACTIVATED
LAVATORY FAUCETS
EEAAFF--227755 SSeerriieess
Solar Powered
Sensor Activated
Lavatory Faucets
TThhee nneeww OOppttiimmaa SSoolliiss™™ ssoollaarr ppoowweerreedd
ffaauucceett —— BBrriinnggiinngg iinntteelllliiggeennccee ttoo wwaatteerr
The first solar powered electronic faucet's integrated power plant
transforms light into electrical energy. Optimal performance any place,
any time; in sunlight or even artificial light. The unique "Solar Energy
Module" utilizes any light source efficiently.
Sloan’s new Optima EAF-275 series electronic hand washing faucets
operate by means of a dual infrared sensor and microprocessor based
logic. The modular design incorporates all of the operating components
of the faucet, including the sensor, solenoid, circuitry and solar energy
module above the sink within a die-cast metal spout.
ISM models feature an integral temperature control lever which allows
the user to adjust the water temperature. This adjustment can also be
converted to a fixed setting. EAF faucets ordered without the ISM
variation must be connected to a single, pre-tempered water supply.
Optima EAF-275 series faucets include a 6 VDC lithium battery back-up
power source.
The following instructions will serve as a guide when installing the Sloan
Optima EAF-275 series sensor activated faucets. As always, good safety
practices and care are recommended when installing your new faucet. If
further assistance is required, contact your nearest Sloan Representative
office or the Sloan Installation Engineering Department at:
1-888-SLOAN-14 (1-888-756-2614)
LIMITED WARRANTY
Sloan Valve Company warrants its Optima EAF-275 Series Electronic Hand Washing Faucets to be made of first class materials, free from defects of material or
workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and
serviced, for a period of three years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which
prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will
be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products
directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the battery.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
FAUCET VARIATIONS
-ISM Integral Spout Mixer
PRIOR TO INSTALLATION
Prior to installing the Sloan Optima EAF-275 Series faucet, install the
items listed below. Also, refer to Figures 1A thru 1C.
• Lavatory/sink
• Drain line
• Hot and cold water supply lines or pre-tempered water supply line
IMPORTANT:
• ALL PLUMBING IS TO BE INSTALLED IN ACCORDANCE WITH
APPLICABLE CODES AND REGULATIONS.
• FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
• KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT
COMPONENT PART DAMAGE! DO NOT USE ANY SEALANT ON
COMPRESSION FITTINGS.
Trim Plates
When the EAF faucet is installed on a sink that has three (3) hole
punchings, a Trim Plate should be used.
TTrriimm PPllaatteess mmuusstt bbee ssppeecciiffiieedd
aanndd oorrddeerreedd sseeppaarraatteellyy..
ETF-312-A Trim Plate for 4” (102 mm) Centerset Sink
ETF-510-A Trim Plate for 8” (203 mm) Centerset Sink
TOOLS REQUIRED FOR INSTALLATION
• 13 mm open end wrench or nut driver for faucet retainer nut
• 3/4” open end wrench for female end of flex hose