Installation Guide

ManualsBrandsSloan ManualsBathroom Sink FaucetsOptima Polished Chrome Touchless Single Hole Bathroom Sink Faucet

Code No. 0816490

Rev. 2b (05/09)

INSTALLATION INSTRUCTIONS FOR ELECTRONIC

SENSOR ACTIVATED LAVATORY FAUCETS

LIMITED WARRANTY

Sloan Valve Company warrants its Optima EAF-275, EAF-250, EAF-225 and EAF-200 Series Electronic Hand Washing Faucets to be made of first class materials,

free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner

when properly installed and serviced, for a period of three years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace

any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this

warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan

Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the battery.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

FAUCET ROUGH-IN

FAUCET VARIATIONS

-ISM Integral Spout Mixer (All Series)

-IC -Click Feature (All Series)

-DPU Drain Pop Up (EAF-200/225/250 Series)

-P Plug-in Transformer (EAF-200 Series)

-LT Less Transformer (EAF-200 Series)

PRIOR TO INSTALLATION

Prior to installing the Sloan Optima EAF-275/

EAF-250/EAF-200/EAF-225 Series Faucets, install

the items listed below. Also, refer to rough-in

illustrations.

• Lavatory/sink

• Drain line

• Hot and cold water supply lines or pre-tempered

water supply line

Important:

• ALL PLUMBING SHOULD BE INSTALLED IN

ACCORDANCE WITH APPLICABLE CODES AND

REGULATIONS.

• FLUSH ALL WATER LINES PRIOR TO MAKING

CONNECTIONS.

• KEEP THREAD SEALANT OUT OF YOUR WATERWAY

TO PREVENT COMPONENT PART DAMAGE! DO

NOT USE ANY SEALANT ON COMPRESSION

FITTINGS.

Trim Plates

When the EAF Faucet is installed on a sink that has

three (3) hole punchings, a Trim Plate should be used.

Trim Plates must be specified and ordered

separately.

ETF-312-A Trim Plate for 4” (102 mm) Centerset Sink

ETF-510-A Trim Plate for 8” (203 mm) Centerset Sink

TOOLS REQUIRED FOR INSTALLATION

• 13 mm open end wrench or nut driver for faucet

retainer nut

• 3/4” open end wrench for female end of flex hose

SPOUT

TEMPERED

SUPPLY

O-RING

GASKET

RETAINER

NUT

1-3/16” (30 mm) MIN.

DIA. HOLE REQUIRED

13” (330 mm)

LONG FLEX HOSE

5-11/32”

(136 mm)

24º

2-1/16”

(52 mm)

2-9/16”

(65 mm)

2-1/16”

(52 mm)

4-11/32”

(110 mm)

MODELS EAF-200/250/275 ‡

2.2 gpm (8.3 Lpm) Max. Flow Aerator ‡

Faucets with Single Line Water Supply

EAF-250 Series

Battery Powered, Sensor

Activated Lavatory Faucets

EAF-200 Series

Transformer Powered, Sensor

Activated Lavatory Faucets

MODELS EAF-200/225/250/275-ISM ‡

MODELS EAF-200/225/250-ISM-IC

MODELS EAF-200/225/250-ISM-DPU-IC

2.2 gpm (8.3 Lpm) Max. Flow Aerator ‡

Faucets with Hot and Cold Water Supply

HOT

SUPPLY

COLD

SUPPLY

MIXING LEVER

(Can Be Set and Removed)

1-1/2” (38 mm)

MAX. DECK

THICKNESS

SPOUT

O-RING

1-3/16” (30 mm) MIN.

DIA. HOLE REQUIRED

GASKET

RETAINER

NUT

13” (330 mm)

LONG FLEX HOSE

1-1/2” (38 mm)

MAX. DECK

THICKNESS

If a connection to separate hot and cold

water supplies is desired, then a Bak-Chek

tee fitting (not supplied) must be used prior

to connecting to the faucet.

EAF-275 Series

Solar Powered with Battery

Backup Sensor Activated

Lavatory Faucets

FAUCET SPOUT

DIMENSIONS

‡ EAF-275 Series Faucets are furnished with a 0.5 gpm (1.9 Lpm) Aerator Spray Head.

EAF-225 Series

Transformer Powered,

Sensor Activated Lavatory

Faucets with Temperature

Indicating Illumination

(Models shown

with ISM Integral

Spout Mixer)

Summary of content (6 pages)

PAGE 1
FAUCET VARIATIONS Code No. 0816490 Rev. 2b (05/09) -ISM -IC -DPU -P -LT INSTALLATION INSTRUCTIONS FOR ELECTRONIC SENSOR ACTIVATED LAVATORY FAUCETS Integral Spout Mixer (All Series) -Click Feature (All Series) Drain Pop Up (EAF-200/225/250 Series) Plug-in Transformer (EAF-200 Series) Less Transformer (EAF-200 Series) PRIOR TO INSTALLATION Prior to installing the Sloan Optima EAF-275/ EAF-250/EAF-200/EAF-225 Series Faucets, install the items listed below. Also, refer to rough-in illustrations.
PAGE 2
1 Install Faucet. Slide Gasket over Flex Hose(s) and secure with Faucet Retainer and Nut. 2 A Remove Nut, Faucet Retainer and Gasket. Do Not remove the O-ring from base of Faucet. O-RING — DO NOT REMOVE FAUCET GASKET O-RING FAUCET RETAINER B Install Faucet with O-ring NUT GASKET FAUCET into the center hole in deck or lavatory — 1-3/16" (30 mm) min. hole required. Note: If installing the Faucet on a three (3) hole sink, a Trim Plate should be installed at this time.
PAGE 3
5 Activate Faucet. 6 Set and Fix Temperature. (Model EAF-225 see page 5) A Adjust lever to set temperature. A Activate Faucet by pressing the button one (1) time, then immediately step away. Faucet will run for four (4) seconds and the range will automatically adjust to its environment. Wait ten (10) seconds after water shuts off before using Faucet. B Optional — To fix temperature, set lever to the desired position, then remove lever and plug hole with Cap. B Activate Faucet and check for leaks.
PAGE 4
Model EAF-225 Only Functions RED HOT End Position WHITE Tempered Position BLUE Cold End Position Setting Brightness of Illumination A Remove cover. D Adjust the illumination by turning the mixing lever to desired brightness. B Press button for approximately 5 seconds. E Press button once. 4 C When illuminant glows purple, release. F Replace top cover.
PAGE 5
Model EAF-225 Only Calibrating the illuminant colors (RED - White - BLUE) to water temperature A Remove cover. D Adjust mixing lever for position RED/hot and press button once. G Illuminant flashes BLUE. B Press button twice and release. E Illuminant flashes WHITE. H Adjust mixing lever for position BLUE/cold and press button once. 5 C Illuminant flashes red. F Adjust mixing lever for position WHITE/temperate and press button once. I Replace cover.
PAGE 6
PARTS LIST -Click SETTINGS Function Press Button LED Signal Continuous Run — 2 minute default setting (adjustable from 1 - 20 minutes) 1 time for 2 seconds 5 short flashes reset: Temporary Off Permanent Off 5 short flashes followed by periodic flashing reset: 4 Periodic flashing and then 2 long flashes 5 1 time 2 times (double click) and then 1 time for 5 seconds 13 10 5 short flashes followed by 4 short flashes TROUBLESHOOTING GUIDE 1.