Installation Sheet

ManualsBrandsSloan ManualsSoap DispensersSloan AC Powered, Touchless (Sensor Operated) Soap Dispenser

Installation & Operating

Instruction Manual

Thoroughly read this instruction booklet before

installing or operating the Sloan dispenser.

Keep the Installation & Operating

Instruction Manual with other product

information for future reference.

Sensor-Operated Dispenser

ESD-400 Sensor-Operated, Deck-Mount Foam

Soap Dispenser

Specifications

Width

1.747

” (44.37 mm)

Height 4.40“ (118 mm)

Depth 4.50” (114.3 mm)

Dispenser Rate Approximately

1.2 mL per use

Capacity 1000 mL bottle

Specifications are subject to change without

notice.

Table of Contents Page

Parts/Dimensions 2

Installation Instructions 3-5

Operation 6

Maintenance/Replacements 6-7

Emergency Measures 8

Consumables 8

Sensor-

Operated,

Deck-Mount

Foam Soap

Dispenser

Code. 0816685

Rev.1 (02/15)

Summary of content (8 pages)

PAGE 1
SensorOperated, Deck-Mount Foam Soap Dispenser Installation & Operating Instruction Manual Thoroughly read this instruction booklet before installing or operating the Sloan dispenser. Keep the Installation & Operating Instruction Manual with other product information for future reference. Sensor-Operated Dispenser ESD-400 Sensor-Operated, Deck-Mount Foam Soap Dispenser Specifications Width Height Depth Dispenser Rate Capacity 1.747” (44.37 mm) 4.40“ (118 mm) 4.50” (114.3 mm) Approximately 1.
PAGE 2
OVERVIEW OF PARTS AND DIMENSIONS Note: Deck mount foam soap dispenser shown mounted with faucet for reference. 1.91” (48.5 mm) Foam soap dispenser 4.50” (114.3 mm) Foam soap dispenser 4.40” (111.8 mm) Liquid soap and air tubes 9.25” (235 mm) 2.25” (57 mm) Foam tank case unit Wiring 7.
PAGE 3
INSTALLATION Check that all parts are included in original packaging for proper installation. where the unit may be exposed to direct sunlight. Install the unit on a sturdy horizontal surface that is in ambient temperature (0-35°C/32°-95°F).
PAGE 4
INSTALLATION Air tube from foam soap dispenser STEP 3. Foam soap tube from foam soap dispenser Install foam tank case unit to wall Before installing on the wall, check that no other piping and wiring is running behind hole locations. Wall should be sufficiently reinforced or risk failure due to foam tank case unit falling. Tube clamps Air tube fitting Foam soap tube fitting • Determine a temporary position for mounting the foam tank case unit.
PAGE 5
Connect wiring Protect wire connections Connect the relay harness, which comes from the bottom of the foam tank base case unit, with the hand sensor harness, which comes from the foam soap dispenser. Feed the connectors of the relay harness and hand sensor harness into the connector case as shown in illustration. After positioning all wiring, fold the connector case in half and close using two stainless steel panhead screws.
PAGE 6
OPERATION MAINTENANCE Operation Replacing Soap Mount soap bottle to the foam tank case unit. Press the reset switch, which begins the pumping cycle to purge air from the tube. This step may be required twice to completely prime the unit. The foam soap indicator light on the foam soap dispenser blinks and stops dispensing when the soap bottle in the foam tank case unit runs out. Change the soap bottle. Place hands under foam soap dispenser.
PAGE 7
Cleaning the hand sensor Cleaning foam soap dispenser Clean the hand sensor periodically (about once a month) according to the following procedure: • Press the operation switch to OFF (the operation light goes off). If the tip of the soap nozzle is clogged, the dispensing capability may fail or function partially. Clean the nozzle according to the following procedure: • Gently wipe the hand sensor area with a cloth moistened with warm water.
PAGE 8
EMERGENCY MEASURES Take action according to the chemical being used as listed on the container. See the Safety Data Sheets. Eye Contact: Flush eyes with water for a minimum of 15 minutes and consult a physician immediately. Ingestion: Drink water to induce vomiting and consult a physician immediately. Inhalation: Get fresh air immediately. If condition does not improve, consult a physician immediately. CONSUMABLES Product No. SJS-1751 SJS-1751-1 SJS-1751-3 SJS-1751-4 Description Order No.