Installation Sheet

ManualsBrandsSloan ManualsBathroom AccessoriesXlerator Collection EHD-502-CP-HEPA Wall Mounted Sensor Operated Hand Dryer in Polished Chrome Color

RECEIVING SHIPMENT

1. Unpack all items from the shipping box.

2. Inspect items against the following list.

1. Hand Dryer

2. Tamper Proof 5/32” Hex security bit wrench

3. Installation and Owner’s Manual.

4. Report any missing or damaged items.

5. Locate the Dryer Model Number and Serial Number on

the Dryer nameplate and record the data below.

6. Read and save these instructions.

1 2 3

Dryer Model

Serial Number

Date Of Purchase

110–120V 11.3 – 12.2A

208–277V 5.6 – 6.2A

110–120V 4.3 – 4.5A XLERATOReco

208–277V 2 – 2.2A XLERATOReco

IMPORTANT SAFETY INSTRUCTIONS

PRE INSTALLATION WIRING SAFETY INSTRUCTIONS

• Check that the electrical supply corresponds to that shown

on the rating sticker of unit. Do not connect the dryer to any

electrical supply other than that stated on the rating sticker of

the unit. Permanent damage or improper, unsafe operation of

the unit may result.

• Make sure electricity is switched off at the main panel before

installing, maintaining or cleaning this hand dryer.

• The Dryer must be installed in accordance with current

local wiring and building regulations.

• Do not wire this hand dryer into the lighting circuit. It must be

protected by an independent circuit.

• The Dryer is intended to be permanently connected to the

power supply, and must be properly grounded.

Warning: For proper electrical connections,

check your local building codes.

Your unit must be installed by a qualiﬁed,

licensed electrician.

Warning: To reduce the risk of ﬁre, elec-

tric shock or injury to persons, observe the

following:

A. Use this unit only in the manner intended by the

manufacturer.

B. Before servicing or cleaning unit, switch power

off at service panel and lock the service disconnect-

ing means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

GENERAL SAFETY INSTRUCTIONS

• Troubleshooting and internal maintenance must be performed

by qualied service personnel.

• Do not use any power wash equipment for cleaning on or

near this unit.

• Do not use the Sloan XLERATOR dryer for drying hair.

• Do not obstruct air inlets or outlets.

INSTALLATION INSTRUCTIONS AND OWNERS

MANUAL

FOR SLOAN XLERATOR

AND SLOAN

XLERATOReco

HAND DRYER

EHD-500 SERIES

MODELS: EHD-501

BMC

W GR C

WITH OR WITHOUT SUFFIX:

ECO H

MODEL INFORMATION

Code No. 0816862

Rev.1 (11/18)

Summary of content (8 pages)

PAGE 1
Code No. 0816862 Rev.1 (11/18) INSTALLATION INSTRUCTIONS AND OWNERS MANUAL FOR SLOAN XLERATOR® AND SLOAN XLERATOReco®HAND DRYER EHD-500 SERIES MODELS: EHD-501 BMC W GR C WITH OR WITHOUT SUFFIX: ECO BN H RECEIVING SHIPMENT 1. Unpack all items from the shipping box. 2. Inspect items against the following list. 1. Hand Dryer 2. Tamper Proof 5/32” Hex security bit wrench 3. Installation and Owner’s Manual. 4. Report any missing or damaged items. 5.
PAGE 2
READ AND SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS 1. Disconnect the power source previously brought to the hand dryer location (see pre installation wiring). 2. Remove the 2 cover mounting screws using the Tamper-Proof Wrench supplied. Lift the cover to remove from base plate. 3. If electrical wiring entry is to be made from the rear, remove the appropriate pre-formed knockout on the base plate.
PAGE 3
READ AND SAVE THESE INSTRUCTIONS CLEANING AND MAINTENANCE OUTSIDE: Loosen dirt and grime by gently washing the cover (including air inlet holes). Use a soft cloth or sponge and a mild soap or detergent with lukewarm water. INSIDE: Sloan recommends to inspect and clean the inside of the dryer as required at least once per year, or if performance diminishes. Heavier usage, or an environment that contains excessive lint, dust or other particles, will require more frequent cleaning.
PAGE 4
CODE CHART Codes are displayed by the flashing of the red LED light in the sensor behind air outlet. Normal operation will be indicated by the red LED being on when not drying and off when hands are under the sensor. PARTS LIST Note: Only parts with material numbers noted are available for purchase.
PAGE 5
Codigo No. 0816862 Rev.1 (11/18) MANUAL DE INSTALACIÓN Y USO DE LOS MODELOS DE SECADORAS DE MANO SLOAN XLERATOR® Y SLOAN XLERATOReco® SERIE EHD-500 MODELOS: EHD-501 BMC W GR C CON O SIN SUFIJO: BN ECO H AL RECIBIR EL ENVÍO 1. Desempaque todos los artículos de la caja de envío. 2. Coteje los artículos con la siguiente lista. 1. Secadora de manos 2. Llave a prueba de manipulación 3. Manual de instalación y uso 3. Reporte cualquier artículo faltante o dañado. 4.
PAGE 6
LEA Y GUARDE ESTAS INSTRUCCIONES INSTRUCCIONES DE INSTALACIÓN 6. Identifique el voltaje de la secadora en la etiqueta de 1. Desconecte la fuente de poder llevada previamente a la calibración de la unidad. Después conéctela a un circuito ubicación de la secadora de manos (vea el cableado previo ramal dedicado que no exceda los 20 amperes. a la instalación). 7. Fije el cableado eléctrico a las terminales como se indica 2.
PAGE 7
LEA Y GUARDE ESTAS INSTRUCCIONES LIMPIEZA Y MANTENIMIENTO EXTERIOR: Afloje la suciedad y la mugre lavando suavemente la cubierta (incluyendo los agujeros de toma de aire). Use un paño suave o una esponja y un jabón o detergente suave con agua tibia. INTERIOR: Sloan recomienda inspeccionar y limpiar debidamente el interior de la secadora al menos una vez al año para que no mengüe su desempeño.
PAGE 8
TABLA DE CÓDIGOS Los códigos se indican por el parpadeo de la luz LED roja del detector, detrás de la salida de aire.La operación normal está indicada si la luz LED roja está encendida cuando no está secando y apagada cuando las manos estén abajo del detector. LISTA DE PARTES Nota: Solo las piezas con los números de material indicados están disponibles para compra.