Installation Sheet

ManualsBrandsSloan ManualsToilet Flush Valves Repair Parts3370010

Code No. 0816641

Rev. 5 (03/15)

INSTALLATION INSTRUCTIONS FOR RETROFIT AND COMPLETE VALVE

INSTALLATION FOR SLOAN SOLIS

, SOLAR POWERED,

SINGLE AND DUAL FLUSH WATER CLOSETS AND URINALS

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship

for a period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve

Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole

and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be allowed for labor, transportation or other costs.

This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not

cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE

COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

RESS Series Retrofit Conversion Kit Models

RESS Sloan SOLIS

models are used to convert existing Flushometers to Solar Powered, Sensor Activated

Sloan SOLIS

Dual Flush Water Closet Models can be furnished for

the following:

1.1 gpf/4.2 Lpf Reduced Flush

1.6 gpf/6.0 Lpf (Full Flush) For Low Consumption Bowls

Sloan SOLIS

Water Closet Models can be furnished for the

following:

1.28 gpf/4.7 Lpf High Efficiency

1.1 gpf/4.2 Lpf High Efficiency

Sloan SOLIS

Urinal Models can be furnished for the following:

0.125 gpf/0.5 Lpf High Efficiency

0.25 gpf/1.0 Lpf High Efficiency

0.5 gpf/1.9 Lpf High Efficiency

8100 Series Complete Flushometer Models

8100 Series Sloan SOLIS

Valves are complete Flushometer Valves and ideal for new installations.

Reducing Your Water Footprint.

™

Summary of content (10 pages)

PAGE 1
Code No. 0816641 Rev. 5 (03/15) INSTALLATION INSTRUCTIONS FOR RETROFIT AND COMPLETE VALVE INSTALLATION FOR SLOAN SOLIS®, SOLAR POWERED, SINGLE AND DUAL FLUSH WATER CLOSETS AND URINALS Reducing Your Water Footprint.™ 8100 Series Complete Flushometer Models 8100 Series Sloan SOLIS® Valves are complete Flushometer Valves and ideal for new installations.
PAGE 2
VALVE ROUGH-IN Water Closet Installation Typical Water Closet Installation Model 8111, 8113, 8115, and 8116 Model 8137 Reference for RESS-C Retrofit Reference for RESS-C Retrofit 2¼” (57 mm) MIN. 2¼” (57 mm) MIN. “Y” 1” I.P.S. (25 mm DN) SUPPLY C/L OF FIXTURE 1” I.P.S. (25 mm DN) SUPPLY 5” (127 mm) 4¾” (121 mm) C/L OF FIXTURE 4¾” (121 mm) “X” 36” (914 mm) 28” (700 mm) FINISHED FLOOR C/L OF WASTE FINISHED FLOOR FINISHED WALL 1-3/4” (44 mm) Model “X” 2-1/2” (64 mm) MIN.
PAGE 3
!!! IMPORTANT !!! !!! IMPORTANT !!! WITH THE EXCEPTION OF CONTROL STOP INLET, DO NOT USE PIPE SEALANT OR PLUMBING GREASE ON ANY VALVE COMPONENT OR COUPLING! THE STRAP WRENCH PROVIDED WITH SLOAN SOLIS® IS A CONVENIENCE TOOL AND IS NOT TO BE USED TO REMOVE OR INSTALL THE FLUSHOMETER COUPLINGS. USE STRAP WRENCH ONLY TO INSTALL SLOAN SOLIS® LOCKING RING. !!! IMPORTANT !!! NEVER OPEN CONTROL STOP TO WHERE THE FLOW FROM THE VALVE EXCEEDS THE FLOW CAPABILITY OF THE FIXTURE.
PAGE 4
2 - INSTALL COVER TUBE, WALL FLANGE AND CONTROL STOP TO SUPPLY PIPE A Measure from finished wall to first thread of Adapter or threaded supply pipe (dimension “X”). Cut Cover Tube to this length. C WATER SUPPLY PIPE “X” SWEAT SOLDER ADAPTER Thread Control Stop onto pipe. Tighten with a wrench. IRON PIPE NIPPLE OR COPPER PIPE WITH SWEAT SOLDER ADAPTER SET SCREW COVER TUBE COVER TUBE B Slide Cover Tube over pipe. Slide Wall Flange over Cover Tube until against wall.
PAGE 5
6 - WHEN RETROFITTING AN EXISTING VALVE, START HERE. REMOVE COMPONENTS FROM EXISITING FLUSHOMETER (RESS RETROFIT INSTALLATIONS ONLY) A Remove Control Stop Cap. B Turn off water supply at Control Stop. Push Valve Handle to relieve water pressure. C Remove Outside and Inside Covers and old Inside Parts Kit. D Remove old Handle Assembly and Gasket. E Install Chrome Handle Cap with Gasket to handle opening on Flushometer Body. Tighten Chrome Handle Cap securely.
PAGE 6
9 - TIGHTEN LOCKING RING A B !!! IMPORTANT !!! Thread Locking Ring onto Valve Body. THE LOCKING RING MUST BE INSTALLED DOWN PAST THE VALVE BODY THREADS BY AT LEAST ONE THREAD. IF DIFFICULTY IS EXPERIENCED INSTALLING THE LOCKING RING, TURN THE LOCKING RING BACK AND FORTH, EACH TIME WORKING IT FURTHER DOWN THE THREADS. THE LOCKING RING WILL ACT AS A THREAD CHASER IN THE EVENT THERE HAS BEEN A BUILD-UP OF MATTER ON THE THREADS OF THE OLD VALVE BODY.
PAGE 7
11 - TEST SENSOR ACTIVATION The Sloan SOLIS® has a factory set sensing range: Water Closet Models - 22” to 42” (559 mm to 1067 mm) and Urinal Models - 15” to 30” (381 mm to 762 mm) A Test Sensor with Cover in Place. B Stand in front of Sensor for ten (10) seconds C Step away from Sensor and listen for “CLICK.” THE FACTORY SETTING SHOULD BE SATISFACTORY FOR MOST INSTALLATIONS. IF A RANGE ADJUSTMENT IS REQUIRED, REFER TO THE RANGE ADJUSTMENT INSTRUCTIONS ON THIS PAGE.
PAGE 8
RANGE ADJUSTMENT (ADJUST ONLY IF NECESSARY) COUNTERCLOCKWISE The Sloan SOLIS® has a factory set sensing range: Water Closet Models - 22” to 42” (559 mm to 1067 mm) Urinal Models - 15” to 30” (381 mm to 762 mm) The factory setting should be satisfactory for most installations. If the range is too short (i.e., not picking up users) or too long (i.e., picking up opposite wall or stall door) the range can be adjusted. Note: Water DOES NOT have to be turned off to adjust range.
PAGE 9
TROUBLESHOOTING GUIDE 1. Sensor Flashes Continuously Only When User Steps Within Range. A. Unit in Start-Up mode; no problem. This feature is active for the first ten (10) minutes of operation. 2. Valve Does Not Flush; Sensor Not Picking Up User. A. Range too short; increase the range. 3. Valve Does Not Flush; Sensor Picking Up Opposite Wall or Surface, or Only Flushes When Someone Walks By. Light Flashes Continuously for First 10 Minutes Even with No One in Front of the Sensor. A.
PAGE 10
PARTS LIST Item # Part # Description Items Included with RESS Retrofit and Complete Sloan SOLIS® Valves 1 EBV-304-A EBV-379-A WES-24-A EBV-306-A EBV-328-A EBV-325-A EBV-320-A WES-28-A EBV-321-A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 EBV-311-A EBV-309-A EBV-14 EBV-30 EBV-312-A-C EBV-312-A-U EBV-382-A WES-33-A EBV-134 EBV-145-A EBV-136-A † † † EBV-1017-A EBV-91 EBV-22 EBV-137 WES-27 WES-29 Cover/Sensor/Assembly - Closet SOLIS 1.6 & 1.