Installation Guide

ManualsBrandsSloan ManualsToilet Flush Valves Repair Parts3780018

SLOAN FLUSHOMETER I.I. — Rev. 0 (10/05)

Code No. 0816558

INSTALLATION INSTRUCTIONS FOR EXPOSED SLOAN

WATER CLOSET AND URINAL FLUSHOMETERS

LIMITED WARRANTY

Sloan Valve Company warrants its Sloan Flushometers to be made of first class materials, free from defects of material or workmanship under

normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and

serviced, for a period of three years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option,

repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the

sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only

to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

PRIOR TO INSTALLATION

Before you install the Sloan Flushometer, be sure the

items listed below are installed. Also, refer to the rough-

in diagram below.

• Closet fixture

• Drain line

• Water supply line

Important:

• ALL PLUMBING SHOULD BE INSTALLED IN

ACCORDANCE WITH APPLICABLE CODES AND

REGULATIONS.

• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE

AN ADEQUATE VOLUME OF WATER FOR EACH

FIXTURE.

• FLUSH ALL WATER LINES PRIOR TO MAKING

CONNECTIONS.

The Sloan Flushometer is designed to operate with 10 to

100 psi (69 to 689 kPa) of water pressure. THE

MINIMUM PRESSURE REQUIRED TO THE VALVE IS

DETERMINED BY THE TYPE OF FIXTURE SELECTED.

Consult fixture manufacturer for minimum pressure

requirements. Most Low Consumption water closets (1.6

gpf/6.0 Lpf) require a minimum flowing pressure of 25

psi (172 kPa).

TOOLS REQUIRED FOR INSTALLATION

• Straight blade screwdriver

• Sloan A-50 Super-Wrench™, Sloan A-109 Plier

Wrench or smooth jawed spud wrench

SLOAN VALVE COMPANY • 10500 Seymour Avenue • Franklin Park, IL 60131

Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380

www.sloanvalve.com

Closet Flushometer

for 1½” Back Spud

• MODELS 120, 121 & 122

VALVE ROUGH-IN

CARE AND CLEANING OF CHROME AND SPECIAL FINISHES

DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean

Flushometers that may dull the luster and attack the chrome or special decorative

finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel.

While cleaning the bathroom tile, protect the Flushometer from any splattering of

cleaner. Acids and cleaning fluids will discolor or remove chrome plating.

TROUBLESHOOTING GUIDE

1. Valve does not function (no flush).

A. Control Stop or Main Valve is Closed. Open Control Stop or Main Valve.

B. Handle Assembly is worn or damaged. Install Handle Repair Kit or replace

Handle Assembly.

C. Relief Valve is worn or damaged. Replace Inside Parts Kit.

2. Volume of water is not sufficient to siphon fixture.

A. Control Stop is not open wide enough. Adjust Control Stop for desired delivery

of water volume.

B. Urinal Flushometer Parts inside a Closet Flushometer. Replace Inside Urinal

Parts with proper Closet Flushometer Parts.

C. Low Consumption Flushometer installed on a higher Consumption fixture.

Replace Inside Parts Kit with Water Saver Kit.

D. Water Saver Kit installed in old non-Water Saver bowl. Position Refill Head so

that SIDE 1 is in the UP position.

E. Water supply volume or pressure is inadequate. If no gauges are available to

properly measure supply pressure or volume of water at the Flushometer, then

remove the Relief Valve from the Inside Parts Kit, reassemble the Flushometer

and completely open the Control Stop.

• If the fixture siphons, more water volume is required. If a 3.5 gpf Inside

Parts Kit is installed in the Flushometer, then first flip the Refill Head (under

the diaphragm) to obtain a 4.5 gpf volume. If this volume is still inadequate,

remove the Flow Ring from the Guide to obtain a 6.5 gpf Kit. If additional

flow is required, try a Low Pressure Guide Kit.

IIMMPPOORRTTAANNTT —— LLaawwss aanndd

RReegguullaattiioonnss rreeqquuiirriinngg LLooww CCoonnssuummppttiioonn FFiixxttuurreess ((11..66 ggppff//66..00 LLppff WWaat

teerr

CClloosseettss aanndd 11..00 ggppff//33..88 LLppff UUrriinnaallss)) pprroohhiibbiitt tthhee uussee ooff hhiigghheerr fflluusshhiinngg

vvoolluummeess..

• If the fixture does not siphon or if a Low Consumption fixture is installed, or

if the above steps do not prove satisfactory, steps must be taken to increase

the water supply pressure and/or volume. Contact the fixture manufacturer

for minimum water supply requirements of the fixture.

3. Flushometer closes off immediately.

A. Ruptured or damaged Diaphragm. Replace Inside Parts Kit.

B. Enlarged By-pass orifice from corrosion or damage. Replace Inside Parts Kit.

4. Length of flush is too short (short flush).

A. Diaphragm Assembly and Guide Assembly are not hand-tight. Screw the two

assemblies hand-tight.

B. Enlarged By-pass orifice from corrosion or damage. Replace Inside Parts Kit.

C. Urinal Flushometer Parts inside a Closet Flushometer. Replace Inside Urinal

Parts with proper Closet Flushometer Parts.

D. Low Consumption Flushometer installed on a higher Consumption fixture.

Replace Inside Parts Kit with Water Saver Kit.

E. Handle Assembly is damaged. Replace Handle

5. Length of flush is too long (long flush) or continuous.

A. Relief Valve is not seating properly or By-pass orifice is clogged because of

foreign material, or By-pass orifice is closed by an invisible gelatinous film

from “over-treated” water. Disassemble the working parts and wash thoroughly.

NNOOTTEE::

Size of the orifice in the by-pass is of utmost importance for the proper

metering of water into the upper chamber of the flushometer.

DDoo nnoott eennllaarrggee oorr

ddaammaaggee tthhiiss oorriiffiiccee

. Replace inside kit if cleaning does not correct problem.

B. Supply line water pressure has dropped and is not sufficient to close the valve.

Close Control Stop until pressure is restored.

C. Closet Flushometer Parts inside a Urinal Flushometer. Replace Inside Closet

Parts with proper Urinal Flushometer Parts.

D. Inside Cover is damaged. Replace Inside Cover.

6. Chattering noise is heard during flush.

A. The Segment Diaphragm is installed upside-down. Replace the Segment

Diaphragm to the proper position as instructed by markings on the Diaphragm.

A. Inside Cover is damaged. Replace Inside Cover.

7. Handle Leaks.

A. Handle Gasket, Seal or Assembly is damaged. Replace as required.

When assistance is required, please contact Sloan Valve Company Installation

Engineering Department at:

1-888-SLOAN-14 (1-888-756-2614) OR 1-847-233-2016

PARTS LIST

Urinal Flushometer

for 1¼” Top Spud

• MODEL 180

Urinal Flushometer

for ¾” Top Spud

• MODEL 186

Closet Flushometer

for 1½” Top Spud

• MODELS 110/111, 113,

114, 115 & 116

Service Sink

Flushometer for 1½”

Top Spud

• MODEL 117

IItteemm PPaarrtt DDeessccrriippttiioonn

NNoo.. NNoo..

1 † Valve Assembly

2 B-73-A ADA Compliant Handle Assembly

3 H-710-A Bak-Chek

Control Stop

4A V-500-AA 1-1/2" (38 mm) x 9" (229 mm) Vacuum Breaker Assembly ‡

4B V-500-AA 1-1/4" (32 mm) x 9" (229 mm) Vacuum Breaker Assembly

4C V-500-AA 3/4" (19 mm) x 9" (229 mm) Vacuum Breaker Assembly

4D V-500-A Vacuum Breaker Assembly

5 F-109 1-1/2" (38 mm) Elbow Flush Connection

6A F-56-A 1-1/2" (38 mm) Spud Coupling Assembly

6B F-57-A 1-1/4" (32 mm) Spud Coupling Assembly

6C F-58-A 3/4" (19 mm) Spud Coupling Assembly

7 F-7 Supply Flange (Supplied when Valve is not Ordered with Sweat

Solder Kit)

8 H-633-AA 1" (25 mm) Sweat Solder Kit with Cast Set Screw Flange

H-636-AA 3/4" (19 mm) Sweat Solder Kit with Cast Set Screw Flange

† Part number varies with valve model variation; consult factory.

‡ Length varies with valve model variation; consult factory.

For a complete listing of Flushometer Valve components and Repair Kits, see one

of our Maintenance Guides or consult your nearest Plumbing Wholesaler.

For optimum water conservation and Flushometer performance, use only Genuine

Sloan Parts.

NNOOTTIICCEE::

The information contained in this document is subject to change without notice.

4B 4C

MODEL 110/111 MODELS 113, 114,

115 & 116

MODEL 117

MODELS 120, 121, & 122 MODEL 180 MODEL 186

NOTE: Requires 1” I.P.S.

(DN 25 mm) Supply.

IIMMPPOORRTTAANNTT NNOOTTEESS::

• When mounted on an ADA accessible bowl, the rough-in to the supply inlet should be no higher

than 37½” or the handle will exceed maximum height allowances under ADA guidelines.

• New ADAAG Guidelines allow for Split or Offset Grab Bars, check with local authorities or

reference section 604.5.2 of ADAAG.

Summary of content (2 pages)

PAGE 1
CARE AND CLEANING OF CHROME AND SPECIAL FINISHES PARTS LIST SLOAN FLUSHOMETER I.I. — Rev. 0 (10/05) Code No. 0816558 8 DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean Flushometers that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Flushometer from any splattering of cleaner.
PAGE 2
!!! IMPORTANT !!! With the exception of Control Stop Inlet, DO NOT use pipe sealant or plumbing grease on any valve component or coupling! 1 Install Optional Sweat Solder Adapter (only if your supply pipe does not have a male thread) Install Cover Tube, Wall Flange and Control Stop to supply pipe 2 A FINISHED WALL A !!! IMPORTANT !!! Protect the chrome or special finish of Sloan Flushometers — DO NOT USE toothed tools to install or service these valves.