Installation Sheet

ManualsBrandsSloan ManualsBathroom Remodel & Bathroom FixturesAct-O-Matic Institutional Shower Head

The following instructions will serve as a guide when installing the Sloan

Act-O-Matic Shower Head. As always, good safety practices and care are

recommended when installing your new Sloan Act-O-Matic Shower Head. If

further assistance is required, contact your nearest Sloan Representative office.

PRIOR TO INSTALLATION

Prior to installing the Sloan Act-O-Matic Shower Head, install the items listed

below:

• Shower enclosure

• Drain line

• Water supply line (1/2" I.P.S.(13mmDN) male thread requiredforconnection

to shower head)

Important:

• ALL PLUMBING IS TO BE INSTALLED IN ACCORDANCE WITH

APPLICABLE CODES AND REGULATIONS.

• FLUSH ALL WATER LINES UNTIL WATER IS CLEAR BEFORE

INSTALLING SHOWER HEAD.

• WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN ADEQUATE

FLOW OF WATER FOR EACH SHOWER HEAD. MINIMUM WATER

PRESSURE OF 15 PSI (103 kPa) REQUIRED.

TOOLS REQUIRED FOR INSTALLATION

• 1-3/8" wrench

• Slotted screwdriver for adjusting direction of stream, if required

• 5/16" drill

• Hammer

• Phillips head screwdriver, #3

• 5/32" hex wrench

INSTALLATION

Step 1 — Drill Mounting Holes (Figure 1)

Locate shower head mounting holes per Figure 1. Drill four (4) mounting holes

5/16" x 1-1/2" (8 mm x 38 mm). Drive anchors flush with wall surface.

Step 2 — Install Mounting Plate

Secure mounting plate with wings horizontal to wall using four (4) Phillips head

screws provided.

Step 3 — Install Pipe Fitting (Figure 2)

Coat threaded end of water supply line with pipe dope or wrap with sealing tape.

Thread pipe fitting onto water supply line using a 1-3/8" wrench.

AC-450 I.I.

Code No. 0816192

INSTALLATION INSTRUCTIONS

ACT-O-MATIC

INSTITUTIONAL

SHOWER HEADS

AC-450

Self-Cleaning, Wall Mounted,

Shower Head with Adjustable

Spray Direction and Integral

2.5 gpm (9.4 Lpm) Flow Control

2-1/4"

(57 mm)

Made in the U.S.A.

Figure 1

4-3/8" DIA. (111 mm)

SHOWER HEAD

O.D. (REF)

5/16" DIA. x 1-1/2" DEEP (8 mm x 38 mm)

FOR ANCHORS (4) PLACES

1-1/8"

(29 mm)

1/2" I.P.S. (13 mm DN)

MALE PIPE CONNECTION

2-1/4" (57 mm)

ANSI/ASME Standard A112.18.1M

1-1/8"

(29 mm)

1-1/8"

(29 mm)

1-1/8"

(29 mm)

Summary of content (2 pages)

PAGE 1
AC-450 I.I. Code No. 0816192 INSTALLATION INSTRUCTIONS ACT-O-MATIC® INSTITUTIONAL SHOWER HEADS AC-450 Self-Cleaning, Wall Mounted, Shower Head with Adjustable Spray Direction and Integral 2.5 gpm (9.4 Lpm) Flow Control ANSI/ASME Standard A112.18.1M Made in the U.S.A. The following instructions will serve as a guide when installing the Sloan Act-O-Matic Shower Head. As always, good safety practices and care are recommended when installing your new Sloan Act-O-Matic Shower Head.
PAGE 2
ADJUSTMENT SCREW WATER SUPPLY SPRAY DISK PIPE FITTING W/FLOW CONTROL “O” RING ADJUSTMENT SCREW SHOWER HEAD ASSEMBLY MOUNTING PLATE 15o 15o ANCHOR (4) MOUNTING SCREW (4) 30o SHOWER HEAD MOUNTING SCREW Figure 2 Figure 3 Step 4 — Mount Shower Head Assembly (Figure 2) CARE AND CLEANING OF CHROME AND SPECIAL FINISHES Wet pipe fitting “O” Ring with water to lubricate and carefully slide shower head assembly over pipe fitting. Be careful not to damage pipe fitting “O” Ring.