HT805 Series HT805S - HT805C - HT805T - HT805W Owner’s Manual Rev: 602 1650 W.
HT805 Series Owner’s Manual Page 2 Important Safety Instructions CAUTION To reduce the risk of electric shock, do not remove the back panel of the HT805W There are no user-serviceable parts inside. Refer servicing to SLS Loudspeakers or qualified personnel. General Safety - Read and follow all warnings, operating and safety instructions in this manual and on the unit. - Do not use the HT805W near bathtubs, sinks, swimming pools, or other locations where water is present.
HT805 Series Owner’s Manual Page 3 Introduction Welcome to SLS Thank you for choosing SLS Loudspeakers! SLS Loudspeakers is a leader in digital amplification and ribbon technology allowing for a new level of sound reproduction, clarity, and definition. Various technologies and components within the HT805 Series are proprietary to SLS and protected under letters patent. Should you need to contact SLS you can visit our website at www.slsaudio.com or contact our headquarters: SLS Loudspeakers 1650 W.
HT805 Series Owner’s Manual Page 4 General Use and Operation Loudspeaker Positioning The HT805 Series (except the subwoofer) has a very defined vertical dispersion, which helps prevent interaction with the floor and ceiling and extends the nearfield listening area. It is important to set the speakers so the ribbon is approximately at the ear level of the listener(s). The speaker may also be tilted for proper aiming relative to the height that the speaker is placed.
HT805 Series Owner’s Manual Page 5 Loudspeaker Positioning (cont.) For the best stereo imaging setups, position the speakers and the listening area at approximately the corners of an equilateral triangle. The larger the triangle, the bigger the soundstage but a less clearly defined center image. The room will also play an increasing role in the sound. The smaller the triangle, the more immediate the presentation but with a smaller soundstage. We encourage you to experiment within the following guidelines.
HT805 Series Owner’s Manual Page 6 Loudspeaker Positioning (cont.) In home theater setups it is best to try and keep all the speakers at an equal distance from the listening position. If this is not possible, use the level and delay controls on the electronics you are using to level match and time align the signal from each speaker location. You may use the “Large” speaker setting on all HT805 series models.
HT805 Series Owner’s Manual Page 7 Audio Connection (cont.) The HT805W subwoofer will accept both line level signals via RCA jacks or speaker level signals from an amplifier via the binding posts. Do not use a mixture of line level and speaker level connections. Whenever possible, use the line level connections. Use of the Full Range setting uses your receiver - processor to control the crossover point between the subwoofer and satellites.
HT805 Series Owner’s Manual Page 8 Connection Diagram using a dedicated subwoofer output Switch set to FULL RANGE Input signal from dedicated subwoofer output on receiver - processor Adjust level and phase (crossover disabled) Output signal to optional 2nd subwoofer Connection Diagram using a line level stereo output Output signal to amplifier powering the satellites Switch set to LOW PASS Stereo line level signal from preamplifier (preferabley a 2nd independent signal from preamplifiers that have tw
HT805 Series Owner’s Manual Page 9 Connection Diagram using a speaker level stereo output Switch set to LOW PASS Adjust crossover, level and phase Input signal from speaker output of receiver or power amplifier Input signal from speaker output of receiver or power amplifier 80Hz High Pass Output signal directly to satellites 80Hz High Pass Output signal directly to satellites Stray Magnetic Fields The ribbon used in the HT805 series does not produce any stray magnetic fields however the high perform
HT805 Series Owner’s Manual Page 10 4. Specifications Model Operating Range Sensitivity (1W/1m) Horizontal Coverage Angle -6dB Vertical Coverage Angle -6dB Power Handling Max SPL(calculated) @ 1 Meter Recommended Amp Power for Max Output Nominal Impedance Crossover Frequency Transducers – High Freq. Low Freq.