User manual

ENG ENG
Instruction Manual for High Voltage Track Easytec II
®
1. Use as directed:
This product serves exclusively lighting purposes and may:
 only be used with a voltage of 230V/50Hz.
 only be used in dry condition,
 not in damp or dirt-endangered rooms.
 not in areas of high air humidity.
 not be installed in furniture.
 not be exposed to strong mechanical loads or to strong contamination.
 only be installed and operated after a condition inspection if the product is dirty or
has been moistened through storage.
If these points named above are not adhered to, a short circuit or electrical shock may
occur!
2. Technical Data:
Operating voltage: 230V/ 50Hz
Safety class: I
Carrying capacitiy: max. 10 A
Dimensions(H x W): 3,0 x 1,0 cm
Length track: 2,0 m
Weight: 1,0 kg
3. Assembly
Attention: Use only parts, which belong to the product! Otherwise the product or the
installation might not be sufficiently safe. Switch off the power of the mains supply line or
respectively of the connection lead before doing any works.
f) Assembly place:
Make sure that the product is mounted on a stable, even and tilt-fixed background.
The spots should be placed at least so far from the illuminated surface, as indicated as
minimum distance on the type plate of each spot:
. Pay special caution to
easily inflammable objects (e.g. curtains) or electric connections.
Einzelne Montageschritte
 Fasten the suspensions as shown in fig. 1. Arrange the suspensions to follow the
intended course of the track. The maximum distance between each suspension
must not exceed 90 cm.
 Fasten the track to the suspension as shown in fig. 2.
 Use the electrical connector (Art.-No. 184032) to connect two tracks (fig. 3a). Use
the insulated connector (Art.-No. 184172) to connect two tracks with separate
circuits (fig. 3b).
 Equip all track ends with end caps (Protection against electric shock)(fig. 3c).
Operating the product without end caps may be life-threatening.
h) Electrical Connection
 The electric connection may be executed only by an electric expert who is familiar
with the valid directives.
 The product must be able to be separated by an all pole separation from the
current supply.
 Pay attention that the power supply is not damaged in the ceiling/wall, i.e. by
drillin
g,
screws or stron
g
bendin
g
. This can lead to a short circuit.
 Fasten the canopy of the feed-in to the ceiling (fig. 4a). Fasten the feed-in to the
track as shown in fig. 4b. Make sure to fix it securely and ensure a tight electrical
contact.
 For electric connection attach the black or brown wire (live conductor) of the main
power supply with the clamp L and the blue wire (neutral conductor) of the main
power supply with the clamp N. The green-yellow wire (protective conductor) of
the main power supply has to be tightly screwed into the earth clamp
of the
product.
i) Attaching light fixtures with the Easytec II
®
adapter
 Place the adapter beneath the track. Press both adapter sides upwards with the
contacts fitting into the track. The adapter locks up. Tightly fasten the milled screw
to ensure a secure electrical contact. To unlock the adapter push the pin on top
after the milled screw has been loosened.
 Check all connections once in a while for a secure fit.
4. Operation:
Information for the user:
Operate the product only if it is working correctly. Switch off the product with a malfunction
immediately and operate it again only after examination by an electrical specialist.
This is the case, when:
 visible damages appear.
 the product does not work.
 smoke, steam or crackling sounds appear.
 an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may only be carried out
by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not fasten or hang anything on the product!
 Provide free air circulation - cover nothing!
 Do not hang anything on the product, especially no decoration and no electrically
conducting objects.
Never let children play unsupervised with electric products! Children can not always
estimate dangers in dealing with electric energy correctly.
What is to do if a bulb is defect or does not work?
 Disconnect the product from power, before you exchange the bulbs.

Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
 Replace the bulbs only with bulbs of the same data like socket, power and
capacity (see type label on spot). Every other sort of bulb can lead to damages of
the light. Use a piece of fabric to exchange bulbs – do not touch bulbs with bare
fingers. Remove all fingerprints from the bulbs.
 Replacement G9 : Simply stick the bulb in/out of the socket.
 Replacement GU 10 : Insert it with a quarter-turn to the right – removal vice versa.
5. What else has to be considered?
Disconnect the product from power, before you…
 clean or maintain the product.
 do any works on the product or its components (electric expert).
...
x,x m
g)
3 4