433-CMU-40 Instructions Wireless Central Monitoring Unit Caregiver Pocket Pager CordLess Bed and Chair Sensor Pads Wireless Motion Sensor CordLess Floor Mats Wireless Nurse Call Button Wireless Window/Door Exit Alarm S M A R T C A R E G I V E R CO R P O R AT I O N 1229 North McDowell Blvd., Petaluma, CA 94954 | Tel: 800-650-3637 csr@smartcaregiver.com | www.smartcaregiver.
Table of Contents Features Pre-Programmed Instructions Page 4-5 Page 5 • *Pre-Programmed means - components are already programmed to CMU. • You received your CMU with components already programmed. Setup - Programming/Adding Components Page 6 • You received your CMU with NO programming. • You need to add a component.
Mission & Value Statement We are here to help! For safety reasons, program only one component to each number on the Central Monitor. This ensures that the caregiver knows which resident and location to respond to (i.e. if a resident is using a bed pad in their room and a chair pad on their wheelchair.) Please use the chart included in the back of this instruction manual as a legend for the resident component and corresponding number on the Central Monitor.
Features 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Features Explained 1. Call Review Button - Used to review previous alerts (must use this button as the reset button to use this feature and not erase history) 2. Volume Button - Increase or decrease the alert volume 3. Replace Components Button - Button used when replacing components to your CMU 4. Programming Light - Will light up when CMU is in programming mode 5. Program/Add Components Button - Button used when programming components to your CMU 6.
Setup - Programming/Add Components YOUR SYSTEM IS PRE-PROGRAMMED, DO NOT STOP IF FOLLOW THE STEPS BELOW UNLESS YOU NEED TO ADD MORE COMPONENTS. GO TO PAGE 5. To Program Components to Your CMU: Numbers flashing across the screen of the Central Monitor indicates that there are no components currently programmed into the Central Monitor. *READ THESE INSTRUCTIONS FULLY BEFORE BEGINNING TO PROGRAM. 1. Insert batteries into all components requiring a battery. 2.
Detailed Instructions - READ ALL *Example: 1 2 3 Component #1 Component #2 C C C Component #3 C Call / Alarm Switch • Place components in desired order for programming. • Ensure pads are placed on a hard surface with transmitters on and motion sensors are turned off. • Insert 4-C Batteries and plug in provided AC adapter • Make sure batteries are new and in good working order • Put CMU into the UNLOCK position. • Select Alert type.
Detailed Instructions Cont. - READ ALL 5 Program your components: (Choose which apply) Once you have finished programming all desired components move to step 6. TL-2020 Wireless Economy Fall Prevention Monitor • Press and release Call button twice. • Wait for melodic confirmation tone. • The number programmed will now be solid and the next available number will be flashing. • Move to next desired component or Step 6 if finished programming. 433-NC Nurse Call Button • Press nurse call button and release.
433-MS Motion Sensor • Turn switch to “ON” and wave hand in front of motion sensor until CMU activates. This could take 10-15 seconds. • Wait for melodic confirmation tone. • The number programmed will now be solid and the next available number will be flashing. • Move to next desired component or Step 6 if finished programming. 433-EXT Window / Door Exit Alarm • • • • Touch the 2 parts of the sensor together and then separate them. Wait for melodic confirmation tone. Put sensor pieces back together.
Resetting Your CMU 6 Final Step • When you have programmed all of your components, put the CMU into the LOCK position using the switch on the right side of the monitor. • Press and release the RESET button on the front of the CMU and then test your components.
Replace Components To Replace Components on your CMU: Read Directions Before Programming *MAKE SURE THAT NO COMPONENTS ARE BEING ACTIVATED WHEN YOU ARE TRYING TO REPLACE COMPONENTS ON THE CMU. Place new components in the order that you would like to program them. Pads will need to be on a hard flat surface and turned on in order to program correctly. 1. Put the CMU into the UNLOCK position. 2. Press and hold the REPLACE COMPONENTS button for 2 dings and a melodic confirmation tone then release. 3.
Mounting The Monitor 1. Slide mounting bracket off the bottom of the monitor 2. Mount bracket to the wall. 3. Slide hooks on back of CMU onto the mounting bracket Clearing The Monitor To Clear The Monitor: **THIS WILL REMOVE ALL PROGRAMMED COMPONENTS** Move the switch on the side of the monitor to the UNLOCK position. 1. Hold down the PROGRAM / ADD COMPONENTS button and the RESET button simultaneously until you hear a distinct clearing tone. This may take about 5-10 seconds. 2.
Troubleshooting Programming: Are there flashing / scrolling numbers on the screen? • If there are numbers flashing / scrolling across the Central Monitor screen, there is no programming and the monitor is empty. Monitor needs to be programmed. Go to Page 6 Setup - Programming Is there a component that is not programming to the Central Monitor? • If the component is a call button, motion sensor or caregiver pager, check the frequency.
Warning IMPORTANT INFORMATION: Cordless and Wireless Systems rely on wireless technology which is subject to physical and environmental considerations. Please be aware that the transmitter will not be 100% accurate if it is out of range at any time. It is the end-user’s responsibility to make sure that the product is used correctly and within range of each other.
Resident Name # 15 1 21 2 22 3 23 4 24 5 25 6 26 7 27 8 28 9 29 10 30 11 31 12 32 13 33 14 34 15 35 16 36 17 37 18 38 19 39 20 40 Resident Name CMU Legend #
Call Today (800) 650-3637 We take pride in our outstanding customer service. At Smart Caregiver Corporation weCustomer strive to keep ourService customers 100% satisfied. Tel: (800) 650-3637 Fax (707) 781-7440 www.smartcaregiver.com Notes • Low power affects performance. Refer to the features section inside the manual to locate the symbol indicating that battery is low. Replace batteries when this symbol appears on the Central Monitor.
FCC Warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
