Instructions / Assembly
Infinity
™
Magnetic Drive Variable Flow
Performance Pump Kits
SP Submersible Series and VP In-line & Submersible
Series
The Infinity SP and VP series of pumps are high quality
products designed using the latest technological
improvements in water gardening today. These pumps
are suitable for use in ponds, aquariums, fountains,
filters, statuary and aquatic gardens. These pumps
have been developed on the basis of synchronous
technology whereby the electrical parts have been fully
encapsulated in epoxy resin.
The pumps have an economical, powerful and reliable
motor. The SP series is suitable to be used submersibly
in fresh water. The Infinity VP series of pumps are
suitable for installation on dry land for in-line use or
they can be used submersibly in fresh and salt water.
The VP series are equipped with a ceramic shaft
which allows for their use in salt water applications.
Infinity pumps are carefully inspected and tested
to insure both safety and operating performance.
However, failure to follow the instructions and warnings
in this manual may result in pump damage and/or
serious injury. Be sure to read and save this manual
for future reference.
WARNING
The National Electric Code requires that a ground
fault circuit interrupter (GFCI) be used in the branch
circuit supplying electric water pumps and other pond/
aquatics equipment. For any information regarding
the proper installation required for this pump please
contact your local electrical supplies dealer or a
licensed electrician.
Do not remove the grounding pin from the plug.
Do not connect to any voltage other than that
shown on the pump.
Do not pump any liquids other than fresh water
(fresh or salt for VP series) as specifically noted in
the owner’s manual.
Do not use with water above 86°F (30°C.)
Some models of Infinity pumps are equipped with an
internal thermal protector switch that will automatically
turn off the pump in the case of overheating. Once the
pump is cooled, the unit will restart provided that no
irreversible damage has occurred.
Risk of electric shock: This pump is supplied with a
grounding connector and grounding type attachment
plug. To reduce the risk of electric shock, be certain
that the pump is connected only to a properly grounded,
grounding-type electrical receptacle.
NOTE: Insure that the
electrical cord loops
below the electrical
outlet to form a “Drip
Loop”. This will prevent
water from running
down the cord and into
the electrical outlet.
CAUTION & SAFETY WARNINGS
Check that the power supply is properly rated and
fused. If the pump or the power cable does not comply
with your local electrical code standards – DO NOT
connect the pump to the equipment.
To reduce the risk of electrical shock, unplug the power
cord from the receptacle before handling the pump at
any time.
Always disconnect the power before cleaning the
pump or when performing maintenance on the pond or
water area where the pump is being used. This includes
draining or changing the water in your aquatic feature
or putting any part of your body into the water.
Do not connect the pump to the electrical supply while
the pump is out of the water.
Do not lift the pump by the power cord or by pulling
on the cable.
The electrical supply cord of this pump cannot be
replaced. If the power cord is damaged, the pump
should be discarded. Never remove the plug or shorten
the cable. Your guarantee is invalidated if you attempt
to alter the construction of the unit in any way.
Operate the pump completely submerged for proper
cooling (SP Series and VP Series when not used in-line).
Never let the pump run dry as this will damage the
impeller and may also overheat the pump and burn out
the electrical coil.
Never allow the water level in your water feature to
fall below the top of the pump body.
Do not use this product in bathrooms.
Do not use this product if the body of the unit becomes
damaged, swollen or cracked in any way.
If the pump becomes noisy, replace the impeller since
this is a wearable part.
Keep the connection (plug and socket) dry at all times.
The pump is NOT suitable for use in swimming pools,
swimming ponds or other situations where people
could make bodily contact with the water.
Infinity
™
Pumps - Care & Instructions Infinity
™
Pumps - Care & Instructions
PUMP BODY
IMPELLER
IMPELLER
COVER
FRONT COVER
PUMP BODY
IMPELLER
IMPELLER
COVER
FRONT COVER
FILTER
SP Series Parts Diagram
VP Series Parts Diagram