SBP-TBF UPS Series Uninterruptible Power Supply USER'S GUIDE 1000VA, 1400VA, 2000VA Models: SBP1000TBF, SBP1400TBF, SBP2000TBF ® SmartPower SYSTEMS • • • • • • • • • • • • • • • • P.N.16002100 Rev.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for models SBP1000TBF SBP1400TBF and SBP2000-TBF that should be followed during installation and maintenance of the UPS and batteries. Safety CAUTION! • This UPS utilizes voltages that may be hazardous. Do not attempt to disassemble the unit. The unit contains no user serviceable parts. Only factory service personnel may perform repairs.
• Unplug the UPS prior to cleaning and do not use liquid or spray detergent. • Do not dispose of battery or batteries in a fire. The battery may explode. • Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic. • A battery can present a risk of electrical shock and high short circuit current. The following precautions should be observed when working on batteries: 1). Remove watches, rings, or other metal objects from the hand. 2).
3.System Description Front Panel — LED 1. Fault LED + - 2. AC Mode: Load Level LEDs Backup Mode: Battery Capacity LEDs 3. AC Mode: Green Lighting Backup Mode: Green Flashing 4. Power “ON/OFF” Switch Back Panel 1. USB Port (Option) 2. Cooling Fan 3. 4. Modem/Phone/Network Line Surge Protection Circuit Breaker 5. AC Output 6.
Installation and Operation Installing the UPS is as easy as following the steps shown. Be aware the Power Switch must be kept in the “ON” position, otherwise, the UPS will be disabled and your equipment will not be protected during a power failure. 1. Inspection Remove the UPS from its packaging and inspect it for damage that may have occurred during shipping.
4. Computer Connection Connect one computer-related device into each of the power receptacles supplied on the back of the UPS (maximum of three devices). UTBF ~ ~ UPS COMPUTER 5. Modem/Phone line Connection Plug incoming internet line into the “In” socket at the back of the UPS. Use one more Internet line cable and plug one end of the Internet line cable to the “Out” socket at the back of the UPS. Plug the other end to the modem input socket as shown.
6. Serial Cable Connection To allow for unattended system shutdown for your operating system, connect the serial cable as per diagram below. UPS UTBF ~ ~ COMPUTER 7. Turn On/Off The UPS will be turned on automatically at first plug-in. At this moment, press the power switch lightly to turn off the UPS. To turn on the UPS again, just simply press power switch again. Please DO NOT punch it to extend the life of the power switch. +- 8.
10. Battery Removal (SBP1000) Before replacing the battery, turn off the UPS and unplug the UPS cord from the wall outlet. Follow Chart 4 to remove the screw located on the bottom of the front panel and then open the front cover. Remove the front panel Remove the battery cover Chart 4 Chart 5 After removing battery cover (Chart 5), gently extract the battery by pulling attached white vinyl sheet (Chart 6). Disconnect the wires connected to the battery.
Free Software Download SmartPower Systems provides a complete line of software solutions for standalone and networked computers, including SNMP support.
Trouble Shooting Symptom No LED display on the front panel Possible Cause 1. Missing battery 2. Battery defect 3. Power switch is not pressed at least 5 seconds. Remedy 1. Charge battery up to 10 hours 2. Replace with the same type of battery 3. Press power switch for at least 5 seconds Alarm buzzer Overload of the UPS beeps continuously when AC supply is normal Verify that the load matches the UPS capability specified in the specs. When AC power fails, back-up time is shorten. 1.
Specifications SBP1000U-TBF SBP1400U-TBF SBP2000U-TBF OUTPUT Capacity VA / W 1000 / 600 Voltage (on battery) Frequency (on battery) Voltage Regulation (AVR) 1400 / 840 Simulated sine wave at 120V ±10% 2000 / 1200 50 or 60Hz ±1% AVR automatically increases output voltage 17% above input voltage if -9% to -25% of nominal.
LIMITED PRODUCT WARRANTY We warrant this product to be free from defects in material and workmanship for 2 years. The battery has a 2 year warranty. If a product proves to be defective in material or workmanship during the warranty period, we will at our sole option repair or replace the product with a like product. Visit our website for details - www.smartpowersystems.
® SmartPower • • • • • • • • • • • • • • • • SYSTEMS A POWER QUALITY COMPANY 1760 Stebbins Dr. • Houston, TX 77043 1-800-882-8285 • www.smartpowersystems.com Email:support@smartpowersystems.