LM339DR Datasheet

ManualsBrandsSmart Prototyping ManualsInfrared & Light SensorsZio Line Finder (Qwiic, 4 Transceivers)

Table Of Contents

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

LM139-N

LM239-N

LM2901-N

LM3302-N

LM339-N

SNOSBJ3E –NOVEMBER 1999–REVISED DECEMBER 2014

LMx39-N, LM2901-N, LM3302-N Low-Power Low-Offset Voltage Quad Comparators

1 Features 3 Description

The LMx39-N series consists of four independent

• Wide Supply Voltage Range

precision voltage comparators with an offset voltage

• LM139/139A Series 2 to 36 V

or ±1 to ±18 V

specification as low as 2 mV maximum for all four

• LM2901-N: 2 to 36 V

or ±1 to ±18 V

comparators. These comparators were designed

specifically to operate from a single power supply

• LM3302-N: 2 to 28 V

or ±1 to ±14 V

over a wide range of voltages. Operation from split

• Very Low Supply Current Drain (0.8 mA) —

power supplies is also possible and the low power

Independent of Supply Voltage

supply current drain is independent of the magnitude

• Low Input Biasing Current: 25 nA

of the power supply voltage. These comparators also

have a unique characteristic in that the input

• Low Input Offset Current: ±5 nA

common-mode voltage range includes ground, even

• Offset Voltage: ±3 mV

though they are operated from a single power supply

• Input Common-Mode Voltage Range Includes

voltage.

GND

The LMx39-N series was designed to directly

• Differential Input Voltage Range Equal to the

interface with TTL and CMOS. When operated from

Power Supply Voltage

both plus and minus power supplies, the devices

• Low Output Saturation Voltage: 250 mV at 4 mA

directly interface with MOS logic— where the low

power drain of the LM339 is a distinct advantage over

• Output Voltage Compatible With TTL, DTL, ECL,

standard comparators.

MOS, and CMOS Logic Systems

• Advantages:

Device Information

(1)

– High-Precision Comparators

PART NUMBER PACKAGE BODY SIZE (NOM)

– Reduced V

Drift Overtemperature

LM139-N

CDIP (14) 19.56 mm × 6.67 mm

– Eliminates Need for Dual Supplies

LM239-N

SOIC (14) 8.65 mm × 3.91 mm

– Allows Sensing Near GND

LM2901-N

PDIP (14) 19.177 mm × 6.35 mm

– Compatible With All Forms of Logic

CDIP (14) 19.56 mm × 6.67 mm

– Power Drain Suitable for Battery Operation

LM339-N SOIC (14) 8.65 mm × 3.91 mm

PDIP (14) 19.177 mm × 6.35 mm

2 Applications

(1) For all available packages, see the orderable addendum at

• Limit Comparators

the end of the datasheet.

• Simple Analog-to-Digital Converters (ADCs)

• Pulse, Squarewave, and Time Delay Generators

One-Shot Multivibrator With Input Lock Out

• Wide Range VCO; MOS Clock Timers

• Multivibrators and High-Voltage Digital Logic

Gates

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

Summary of content (32 pages)

PAGE 1
Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 LMx39-N, LM2901-N, LM3302-N Low-Power Low-Offset Voltage Quad Comparators 1 Features 3 Description • • • • • The LMx39-N series consists of four independent precision voltage comparators with an offset voltage specification as low as 2 mV maximum for all four comparators.
PAGE 2
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com Table of Contents 1 2 3 4 5 6 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications........
PAGE 3
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 5 Pin Configuration and Functions J, D and NFF Package 14-Pin CDIP, SOIC, PDIP Top View 14-Pin CLGA Package Top View Pin Functions PIN NO.
PAGE 4
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings (1) MIN Supply Voltage, V+ Differential Input Voltage Input Voltage 28 LM139N, LM239N, LM339N, LM2901N LM3302N (2) 36 (2) LM139N, LM239N, LM339N, LM2901N −0.3 36 LM3302 –0.
PAGE 5
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN MAX LM139N, LM239N, LM339N, LM2901N 2 36 LM3302N 2 28 LM139N, LM239N, LM339N, LM2901N ±1 ±18 LM3302N ±1 ±14 LM139/LM139A −55 125 LM2901/LM3302 −40 85 LM239/LM239A −25 85 LM339/LM339A 0 70 Single Supply Supply Voltage Dual Supply Operating Temperature UNIT V °C 6.
PAGE 6
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com 6.5 Electrical Characteristics: LM139A, LM239A, LM339A, LM139 (V+=5 VDC, TA = 25°C (1) unless otherwise stated) PARAMETER TEST CONDITIONS LM139A MIN TYP LM239A, LM339A MAX MIN TYP MAX LM139 MIN TYP MAX UNIT Input Offset Voltage See (2) 1.0 2.0 1.0 2.0 2.0 5.
PAGE 7
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 6.6 Electrical Characteristics: LM239, LM339, LM2901, LM3302 (V+ = 5 VDC, TA = 25°C (1) unless otherwise stated) LM239, LM339 PARAMETER TEST CONDITIONS MI N TYP MAX LM2901 MIN LM3302 TYP MAX MIN TYP MAX UNIT Input Offset Voltage See (2) 2.0 5.0 2.0 7.
PAGE 8
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com 6.7 Typical Characteristics 6.7.1 LM139/LM239/LM339, LM139A/LM239A/LM339A, LM3302 Figure 1. Supply Current Figure 2. Input Current Figure 3. Output Saturation Voltage Figure 4. Response Time for Various Input Overdrives – Negative Transition Figure 5.
PAGE 9
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 6.7.2 LM2901 Figure 6. Supply Current Figure 7. Input Current Figure 8. Output Saturation Voltage Figure 9. Response Time for Various Input Overdrives – Negative Transition Figure 10.
PAGE 10
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com 7 Detailed Description 7.1 Overview The LM139/LM239/LM339 family of devices is a monolithic quad of independently functioning comparators designed to meet the needs for a medium-speed, TTL compatible comparator for industrial applications. Since no antisaturation clamps are used on the output such as a Baker clamp or other active circuitry, the output leakage current in the OFF state is typically 0.
PAGE 11
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 Feature Description (continued) The amount of current which the output device can sink is limited by the drive available (which is independent of V+) and the β of this device. When the maximum current limit is reached (approximately 16 mA), the output transistor will come out of saturation and the output voltage will rise very rapidly.
PAGE 12
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.
PAGE 13
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 Typical Applications (continued) 8.2.2 System Examples Figure 13. Driving CMOS (V+ = 5.0 VDC) Figure 14. Driving TTL (V+ = 5.0 VDC) Figure 15. AND Gate (V+ = 5.0 VDC) Figure 16. OR Gate (V+ = 5.0 VDC) Figure 17. One-Shot Multivibrator (V+= 15 VDC) Figure 18.
PAGE 14
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) Figure 19. One-Shot Multivibrator with Input Lock Out (V+= 15 VDC) Figure 20. Pulse Generator (V+= 15 VDC) Figure 21. Large Fan-In AND Gate (V+= 15 VDC) Figure 22.
PAGE 15
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 Typical Applications (continued) Figure 23. Time Delay Generator (V+= 15 VDC) Figure 24. Non-Inverting Comparator with Hysteresis (V+= 15 VDC) Figure 25. Inverting Comparator With Hysteresis (V+= 15 VDC) Figure 26.
PAGE 16
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) Figure 27. Basic Comparator (V+= 15 VDC) Figure 28. Limit Comparator (V+= 15 VDC) * Or open-collector logic gate without pullup resistor Figure 29. Comparing Input Voltages of Opposite Polarity (V+= 15 VDC) 16 Submit Documentation Feedback Figure 30.
PAGE 17
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 Typical Applications (continued) 250 mVDC ≤ VC ≤ +50 VDC 700 Hz ≤ fO ≤ 100 kHz Figure 31. Crystal Controlled Oscillator (V+= 15 VDC) Figure 32. Two-Decade High-Frequency VCO V+ = +30 VDC Figure 33. Transducer Amplifier (V+= 15 VDC) Figure 34.
PAGE 18
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) 8.2.2.1 Split-Supply Applications Figure 35. MOS Clock Driver (V+ = +15 VDC and V− = −15 VDC) Figure 36. Zero Crossing Detector (V+ = +15 VDC and V− = −15 VDC) Figure 37.
PAGE 19
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N www.ti.com SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 9 Power Supply Recommendations Even in low-frequency applications, the LM139-N can have internal transients which are extremely quick. For this reason, bypassing the power supply with 1.0 µF to ground will provide improved performance; the supply bypass capacitor should be placed as close as possible to the supply pin and have a solid connection to ground. The bypass capacitors should have a low ESR.
PAGE 20
LM139-N, LM239-N, LM2901-N, LM3302-N, LM339-N SNOSBJ3E – NOVEMBER 1999 – REVISED DECEMBER 2014 www.ti.com 11 Device and Documentation Support 11.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 1.
PAGE 21
PACKAGE OPTION ADDENDUM www.ti.
PAGE 22
PACKAGE OPTION ADDENDUM www.ti.com 15-Jan-2021 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production.
PAGE 23
PACKAGE OPTION ADDENDUM www.ti.
PAGE 24
PACKAGE MATERIALS INFORMATION www.ti.com 25-Sep-2019 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2901MX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LM2901MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LM339AMX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.
PAGE 25
PACKAGE MATERIALS INFORMATION www.ti.com 25-Sep-2019 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2901MX SOIC D 14 2500 367.0 367.0 35.0 LM2901MX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LM339AMX SOIC D 14 2500 367.0 367.0 35.0 LM339AMX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LM339MX SOIC D 14 2500 367.0 367.0 35.0 LM339MX/NOPB SOIC D 14 2500 367.0 367.0 35.
PAGE 26
PAGE 27
PACKAGE OUTLINE J0014A CDIP - 5.08 mm max height SCALE 0.900 CERAMIC DUAL IN LINE PACKAGE PIN 1 ID (OPTIONAL) A 4X .005 MIN [0.13] .015-.060 TYP [0.38-1.52] 1 14 12X .100 [2.54] 14X .014-.026 [0.36-0.66] 14X .045-.065 [1.15-1.65] .010 [0.25] C A B .754-.785 [19.15-19.94] 8 7 B .245-.283 [6.22-7.19] .2 MAX TYP [5.08] C .13 MIN TYP [3.3] SEATING PLANE .308-.314 [7.83-7.97] AT GAGE PLANE .015 GAGE PLANE [0.38] 0 -15 TYP 14X .008-.014 [0.2-0.36] 4214771/A 05/2017 NOTES: 1.
PAGE 28
EXAMPLE BOARD LAYOUT J0014A CDIP - 5.08 mm max height CERAMIC DUAL IN LINE PACKAGE (.300 ) TYP [7.62] SEE DETAIL A SEE DETAIL B 1 14 12X (.100 ) [2.54] SYMM 14X ( .039) [1] 8 7 SYMM LAND PATTERN EXAMPLE NON-SOLDER MASK DEFINED SCALE: 5X .002 MAX [0.05] ALL AROUND (.063) [1.6] METAL ( .063) [1.6] SOLDER MASK OPENING METAL (R.002 ) TYP [0.05] .002 MAX [0.05] ALL AROUND SOLDER MASK OPENING DETAIL A DETAIL B SCALE: 15X 13X, SCALE: 15X 4214771/A 05/2017 www.ti.
PAGE 29
PAGE 30
PAGE 31
MECHANICAL DATA NFF0014A N0014A N14A (Rev G) www.ti.
PAGE 32
IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.