Instructions
Instructions for use
WEEE DE 64398562
Function
This ush-mountable single-port USB charger charges the
batteries of mobile devices. The USB charger is ideally suited for
charging tablets which are installed on the wall, using
commercially available wall-mounts. The total output current of
the charger is 2,4 A at 5V ⎓ (+/- 5%).
The maximum permissible voltage is 250V~ 50/60Hz. 16A.
Only install and use this IP20 protected product in protected
locations with an ambient temperature between 5ºC and 35ºC.
Avoid the inuence of moisture, dust, sun or other heat radiation.
For prolonged use, the housing of this product may become
warm. This is normal.
HAZARDWARNING!
• Operate this device only in indoor areas. Avoid the inuence of
moisture, dust, sun or other heat radiation.
• This USB-Charger is part of the building installation. The relevant
standards and directives of the country must be observed during
planning and construction. The operation of the device is
permissible only on the 230V / 50 Hz alternating current network.
Work on the 230V mains may only be carried out by a certied
electrician qualied in your country. The applicable accident
prevention regulations must be observed.
• To avoid an electric shock on the device, please disconnect the
mains voltage to the device (switch o the circuit breaker). Failure
to comply with the installation instructions may cause re or
other hazards.
• The installation may only be carried out in commercially
available ush-mounted wall-boxes (installation boxes), with a
minimum depth of 40mm.
• When connecting the device terminals, observe the type of
cabling which are permissible for this purpose.
• Pay close attention to the wiring diagram!
Mandatory information in accordance with the equipment
safety standard:
Note! Only to be installed by persons with relevant electrical
qualications and experience!*)
Improper installation will result in risk to your own life and risk to
the life of persons using the electrical installation.
With an improper installation, you risk serious material damages,
for example re. You are personnaly reliable for personal injury
and material damages. Please contact a qualied electrical
engineer.
*) Specialist skills required for installation
In particular, the following special knowledge is required for the
installation:
• The applicable “5 Safety Rules”: disconnect; protect against
switching on; verifying mains power disconnect; earthing and
short-circuiting; covering adjacent current-carrying components
or making them inaccessible.
• Selection of suitable tools, measuring equipment and – if
necessary – personal protection equipment;
• Evaluation of measurement results;
• Selection of the electrical installation material to ensure
compliance with the shut-down conditions;
• IP-Protection classes;
• Installation of electrical installation material;
• the resulting connection conditions (conventional protective
multiple earthing, safety earthing, additional measures required
etc.).
Maintenance and cleaning
This USB-Charger is maintenance-free. Any repairs should only be
carried out by a qualied electrician. Clean the unit with a soft,
clean, dry, lint-free cloth only. Please do not use solvent-based
cleaning agents. The plastic housing could be aected by this. Do
not use wet cloths or sponges to clean the socket outlet.
RoHS/WEEE Compliance Statement (Recycling Instructions)
European Directive 2012/19/EU requires that equipment bearing
the trashcan symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately from
regular household waste streams. It is your responsibility to
dispose of this via designated collection facilities appointed by
the government or local authorities. Correct disposal and
recycling will help prevent potential negative consequences to
the environment and human health. For more detailed
information about the disposal of your old equipment, please
contact your local authorities, waste disposal service, or the shop
where you purchased the product.
Technical Specications USB Charger
Input voltage 100 - 250 V~ 50/60 Hz
Input current Max. 1,5 A
Output voltage 4,75 - 5,25 V⎓
Output current 0,01 - 2,4 A
Output power 12 Watt
Power loss (Standby consumption) ≤50 mW
Documentation
© smart things, Germany. All rights reserved. We accept no liability
for technical or printing errors and their consequences. All
trademarks and property rights are acknowledged. Changes in
the sense of technical progress may be made without prior notice.
EN
s24 m
s24 L
s24 -04-0200 sCharge12W manual
8mm 0,75 ... 2 x 2,5 mm2
L
L
N
N
71 mm
71 mm
L
L
L
N
N
N
33 mm
100 - 250 V ~
sCharge 12 W
USB power supply
Type : JP - 3501 UP
Input : 100 - 250 V~ / 50 - 60 Hz,
Output : USB 4,75 - 5,25 V
⎓,
2,4 A max.
Made in China
www.smart-things.com
s24 C
sCharge with micro USB cable
MPNo. sCh-12W-mUSB-1.0
EAN 4260258612240
sCharge with Lightning cable
MPNo. sCh-12W-8pin-1.0
EAN 4260258610246
sCharge with USB-C cable
MPNo. sCh-12W-USB-C-1.0
EAN 4260258612028
cable length 350 mm
s24 sCharge 12W