Installation Guide

ManualsBrandsSMARTCORE by Natural Floors ManualsVinyl Plank50SLV508

SMARTCORE™

Premium Engineered Vinyl Flooring

Installation Instructions

SMARTCORE™ INSTALLATION INSTRUCTIONS (V.1.1)

ATTENTION! READ BEFORE INSTALLING!

FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR

This flooring replicates the look of a natural product which has natural variations in color, texture, and sheen/gloss. For best

visual effect, shuffle planks from several cartons and do not install similar planks next to one another.

SUBFLOOR PREPARATION

Subfloor should be dry and level to 3/16” per 10 ft. radius for best installation results.

SMARTCORE™ Premium Engineered Vinyl Flooring Installation Instructions

READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. If the following instructions leave any

unanswered questions or if additional information is required, please call Natural Floors toll free at 800-404-2675 (706-733-6120).

FLOORING MATERIAL SHOULD BE INSPECTED PRIOR TO INSTALLATION

Responsibility for the suitability of Natural Floors flooring and accompanying products for each individual installation cannot

be assumed by Natural Floors, since Natural Floors has no control over the installer's proper application. Should an

individual plank be doubtful as to appearance or dimension the installer should not use this piece. Natural Floors will send

replacement in a timely fashion.

NOTE: Natural Floors SMARTCORE Premium Engineered Vinyl Floors may be installed with a direct glue-down method on

approved wooden (or) concrete substrates that are on, above, or below grade. Use only Natural Floors recommended flooring

adhesive. Please consult with adhesive manufacturer to determine if suitable for use with this material.

READ BEFORE INSTALLING:

While SMARTCORE is waterproof, it’s not a moisture barrier. It’s still a good idea to make sure your concrete is cured and a

covered with a minimum 6 mil polyfilm moisture barrier, and, when installing over a raised subfloor, that a moisture barrier is

installed in the crawl space. Moisture won’t damage SMARTCORE, but it can get in the walls and structure of the home. A

couple of extra dollars and a few extra minutes is a small investment for the added protection and peace of mind.

Use good common sense installation practices, and you’ll have a successful installation that results in a beautiful floor.

PRE-INSTALLATION JOBSITE REQUIREMENTS

NATURAL FLOORS cannot be held responsible for site conditions.

Carefully examine the flooring prior to installation for color, finish and quality. Ensure adequate lighting for proper inspection. If

flooring is not acceptable, contact your supplier immediately and arrange for replacement. NATURAL FLOORS cannot accept

responsibility for flooring installed with visible defects. Prior to installation of any flooring, the installer must ensure that the jobsite and

subfloor meet the requirements of these instructions. NATURAL FLOORS is not responsible for flooring failure resulting from

unsatisfactory jobsite and/or subfloor conditions.

Flooring should be one of the last items installed in any new construction or remodel project.

Crawl spaces must be a minimum of 18′′ (46 cm) from the ground to the underside of the joists. A ground cover of 6–20 mil black

polyethylene film is essential as a vapor barrier with joints lapped 6′′ (15 cm) and sealed with moisture resistant tape. The crawl space

should have perimeter venting equal to a minimum of 1.5% of the crawl space square footage. These vents should be properly located

to foster cross ventilation. Where necessary, local regulations prevail.

Room temperature and humidity of installation area should be consistent with normal, year-round living conditions for at least one week

before installation of flooring. Maintaining an optimum room temperature of 70

F and a humidity range of 30-50% is recommended.

Summary of content (4 pages)

PAGE 1
SMARTCORE™ Premium Engineered Vinyl Flooring Installation Instructions ATTENTION! READ BEFORE INSTALLING! FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR This flooring replicates the look of a natural product which has natural variations in color, texture, and sheen/gloss. For best visual effect, shuffle planks from several cartons and do not install similar planks next to one another. SUBFLOOR PREPARATION Subfloor should be dry and level to 3/16” per 10 ft. radius for best installation results.
PAGE 2
PRE-INSTALLATION SUBFLOOR REQUIREMENTS All Subfloors must be: • Dry • Structurally sound • Clean: Thoroughly swept and free of all debris • Level: Flat to 3/16” per 10-foot radius Wood subfloors must be dry and well secured. Nail or screw every 6” along joists to avoid squeaking. If not level, sand down high spots and fill low spots with a Portland Based leveling patch. Concrete subfloors must be fully cured, at least 60 days old, and should have minimum 6-mil polyfilm between concrete and ground.
PAGE 3
INSTALLATION INSTRUCTIONS Inspection: Prior to installation, inspect material in daylight for visible faults/damage. Check if subfloor/site conditions comply with the specifications described in these instructions. If you are not satisfied, do not install, and contact your supplier. Before laying: Measure the room at right angle to the direction of the flooring. For best visual effect, planks in the final row should be at least 1/3 of the width of the plank.
PAGE 4
In-floor Radiant Heat: SMARTCORE can be installed using the floating or glue down method. When gluing floor, use only recommended flooring adhesive. • Turn the heat off for 24 hours before, during and 24 hours after installation when installing over radiant heated subfloors • Floor temperature must not exceed 85°F (30°C). • Failure to strictly follow adhesive manufacturer’s guidelines may result in failure and void warranty.