Installation Guide

ManualsBrandsSMARTCORE ManualsVinyl PlankLX42000607

ATTENTION! READ BEFORE INSTALLING!

FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR

ooring replicates the look of a natural product which has natural variations in color, texture, and sheen/gloss.

another.

SUBFLOOR PREPARATION

Subfloor should be dry and level to 3/16” per 10 ft. radius for best installation results.

Angle-Tap Installation Instructions for SMARTCORE

Floors

READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. If the following instructions leave any

unanswered questions or if additional information is required, please call Natural Floors toll free at 800-404-2675 (706-733-6120).

FLOORING MATERIAL SHOULD BE INSPECTED PRIOR TO INSTALLATION

assumed by Natural Floors, since Natural Floors has no control over the installer’s proper application. Should an individual plank

or tile be doubtful as to appearance or dimension the installer should not use this piece. Natural Floors will send a replacement in

a timely fashion.

NOTE:

to determine if suitable for use with this material.

READ BEFORE INSTALLING

While SMARTCORE is waterproof, it’s not a moisture barrier. It’s still a good idea to make sure concrete is cured and tested for

moisture and that a moisture barrier is installed in the crawl space and even under a SMAR oor.

Moisture won’t damage SMARTCORE, but it can get in the walls and structure of the home. A couple of extra dollars and a few

minutes is a small investment for the added protection and peace of mind.

Because houses and buildings, as well as adjacent hardwood or laminate oors, expand and contract, Natural Floors

recommends to leave a ¼” expansion gap between the perimeter walls and any adjacent hardwood oor.

Natural Floors recommends using the glue down method when installing SMARTCORE where it will be exposed to temperatures

greater than 140° F (60° C) or below 32° F (0° C).

Use good common sense installation practices, and you’ll have a successful installation that results in a beautiful oor.

PRE-INSTALLATION JOBSITE REQUIREMENTS

Natural Floors cannot be held responsible for site conditions.

y. Ensure adequate lighting for proper

ooring is not acceptable, contact your supplier immediately and arrange for a replacement. Natural Floors cannot

oor conditions.

Flooring should be one of the last items installed in any new construction or remodel project.

Crawl spaces must be a minimum of 18′′ (46 cm) from the ground to the underside of the joists. A ground cover of 6–20 mil black

lm is essential as a vapor barrier. Joints must be lapped 6′′ (15 cm) and sealed with moisture resistant tape. The

crawl space should have perimeter venting equal to a minimum of 1.5% of the crawl space square footage. These vents should be

properly located to foster cross ventilation. Where necessary, local regulations prevail.

Room temperature and humidity of installation areas should be consistent with normal, year-round living conditions for at least

ooring. Maintaining an optimum room temperature of 70° F and a humidity range of 30-50% is

recommended.

PRE-INSTALLATION SUBFLOOR REQUIREMENTS

• Dry

• Structurally sound

• Clean: Thoroughly swept and free of all debris

• Level: Flat to 3/16” per 10-foot radius

Portland leveling compound.

, in good condition, clean, and level. Do not sand

be installed on

all levels of the

home.

Summary of content (4 pages)

PAGE 1
TM ATTENTION! READ BEFORE INSTALLING! FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR ooring replicates the look of a natural product which has natural variations in color, texture, and sheen/gloss. another. SUBFLOOR PREPARATION Subfloor should be dry and level to 3/16” per 10 ft. radius for best installation results. Angle-Tap Installation Instructions for SMARTCORETM Floors READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
PAGE 2
existing vinyl floors, as they may contain asbestos.
PAGE 3
BRIDGE Step 4: Lock long edge of plank by inserting tongue into groove at an angle and drop in place. Slide plank toward end of previously installed plank until the tongue just touches the groove. Step 5: IMPORTANT! Use hammer and tapping block to tap long edge of plank to ensure a tight fit. ANY GAPPING CAN COMPROMISE THE LOCKING SYSTEM! Step 6: Attach a scrap piece of floor to bridge gap between ends of planks. Step 8: Use hammer and pull bar to lock final piece in row. Insert spacer at end of row.
PAGE 4
In-floor Radiant Heat: SMARTCORE can be installed over radiant heat using the floating or glue down method. When gluing floor, use only Natural Floors recommended adhesive over manufacturer’s recommended substrate. • Turn the heat off for 24 hours before, during and 24 hours after installation when installing over radiant heated subfloors • Floor temperature must not exceed 85°F (30°C). • Failure to strictly follow adhesive manufacturer’s guidelines may result in failure and void the warranty.