HRC200 INDUSTRIAL REMOTE CONTROL USER MANUAL SMARTGEN (ZHENGZHOU) TECHNOLOGY CO., LTD.
Chinese trademark English trademark SmartGen — make your generator smart SmartGen Technology Co., Ltd. No.28 Jinsuo Road Zhengzhou Henan Province P. R. China Tel: +86-371-67988888/67981888/67992951 +86-371-67981000(overseas) Fax: +86-371-67992952 Email: sales@smartgen.cn Web: www.smartgen.com.cn /www.smartgen.cn All rights reserved.
CONTENT 1 OVERVIEW....................................................................................................................................................4 2 PERFORMANCE AND CHARACTERISTICS ................................................................................................4 3 SPECIFICATION ...........................................................................................................................................5 4 PANEL AND WIRING TERMINAL DESCRIPTION ...............
1 OVERVIEW HRC200 is a long-distance wireless remote control with LoRa wireless chip transmission and remote control distance of more than 200m. Used with engine controller, it can realize remote start, stop, load, unload, emergency stop and other functions.
3 SPECIFICATION Table 2 Technical Parameters Item Contents Remote Control HRC200R Working Voltage Powered by 4 AA alkaline batteries. Overall Consumption Can last about 72 hours. Case Dimension (LxWxH) 156.9mmx63mmx53mm (without antenna) Working Conditions Temperature: (-25~+70)°C Humidity: (20~95)%RH Actual working temperature is limited by battery characteristics. Storage Condition Temperature: (-30~+80)°C Weight 0.
4 PANEL AND WIRING TERMINAL DESCRIPTION 4.1 HRC200R REMOTE CONTROL PANEL INDICATORS AND KEYS Fig.1 Remote Control Panel Description Table 3 Indicators Description Indicators Power Status Connection Status Common Alarm/Running Status Description Indicator flashes yellow during pairing process; Indicator keeps red on when battery voltage is low; it keeps green on when battery voltage is normal.
Table 4 Keys Description Icon Key Description Power Long press this key 2s to power on the remote control, then long press this key 2s again to power off the remote control. Start Press this key to send start command. Stop Press this key to send stop command. F1 Press this key to send F1 command. (see the following description.) F2 Long press this key 6s to enter pairing, press it again during the pairing process to cancel pair; Press this key to send F2 command. (see the following description.
4.2 HRC200M RECEIVER PANEL INDICATORS AND INTERNAL KEYS Fig.2 Receiver Panel Description Table 5 Indicators and Keys Description Indicator Description POWER (Indicator: green) Always illuminating: power is normal; Always extinguishing: power is abnormal. RS485 (Indicator: green) Flashing: RS485 communication is normal; Always extinguishing: RS485 communication fails.
Table 6 Communication Channel Configuration Steps Step Description 1 Turn the bottom screw cover anticlockwise to open the base. 2 Change the middle four jumper cap positions to configure the communication channel and replace the battery at the same time. 3 Turn the bottom screw cover clockwise to close the base. The receiver configures the communication channel via dial switch. It is 1 when the dial switch is set to ON position, otherwise it is 0. The default dial switch position is 1111 (515MHz).
Method Process 4. If pairing successfully within 60s, remote control COMM indicator extinguishes after illuminating green 2s, receiver LoRa and RS485 indicators extinguish, POWER indicator keeps green for a long time. Otherwise, COMM indicator keeps red for a long time when the pairing fails. 1. Turn the remote control and receiver to the same channel. (see the communication channel configuration, default channel is 515MHz.) Method 2: Receiver waits for remote control pairing. 2.
4.6 RECEIVER WIRING TERMINAL Fig.5 Mask Diagram Table 9 Wiring Terminal Description No. Function Cable Size Remark 1 COM 0.75mm2 Relay common port. 2 AUX. OUTPUT5 0.75mm2 Normally open volt-free output, capacity DC30V/2A. 3 AUX. OUTPUT4 0.75mm2 Normally open volt-free output, capacity DC30V/2A. 4 AUX. OUTPUT3 0.75mm2 Normally open volt-free output, capacity DC30V/2A. 5 AUX. OUTPUT2 0.75mm2 Normally open volt-free output, capacity DC30V/2A. 6 AUX. OUTPUT1 0.
5 PROGRAMMABLE PARAMETERS 5.1 PC PARAMETER SETTING Before operation, please remember the dial switch position of HRC200M, then set switch to configuration mode (namely 0000 position). PC connects to receiver via RS485 communication conversion module, then the related parameter configuration of receiver can be done via PC software. After the configuration is completed, dial switch must recover to previous position. Fig.6 PC Configuration Interface 5.
No. Item Range Default Description 2: Even Parity 4 Stop Bit (0-1) 0 5 Aux. Input 1 (0-9) 1 6 Aux. Input 2 (0-9) 0 7 Aux. Output 1 (0-6) 5 8 Aux. Output 2 (0-6) 6 9 Aux. Output 3 (0-6) 0 10 Aux. Output 4 (0-6) 0 11 Aux. Output 5 (0-6) 0 12 Aux. Output Output Delay 1 (0-999.9)s 1.0s 13 Aux. Output Output Delay 2 (0-999.9)s 1.0s 14 Aux. Output Output Delay 3 (0-999.9)s 1.0s 15 Aux. Output Output Delay 4 (0-999.9)s 1.0s 16 Aux.
Fig.8 HRC200M Digital Control Application Diagram Table 11 Parameter Configuration No. HRC200 ACC7100A Item Parameter 1 Aux. Input 1 8: Running Status 2 Aux. Input 2 9: Alarm Status 3 Aux. Output 1 2: Stop Control 4 Aux. Output 2 4: Load Control 5 Aux. Output 3 3: Unload Control 6 Aux. Output 4 1: Start Control 1 Aux. Output 2 38: Start Success Output 2 Aux. Output 3 42: Common Alarm 3 Aux. Input 3 34: Simulate Stop Key 4 Aux. Input 4 35: Simulate Load Key 5 Aux.
7 OVERALL AND INSTALLATION DIMENSIONS 7.1 REMOTE CONTROL OVERALL DIMENSION Unit: mm Fig.9 HRC200R Overall Dimension 7.2 RECEIVER OVERALL DIMENSION Installation method can be 35mm guide rail installation or screw (M4) installation. Overall dimension is as follows: Unit: mm Fig.
Fig.11 HRC200M Guide Rail Installation Fig.12 HRC200M Screw Installation 8 TROUBLESHOOTING Table 12 Troubleshooting Symptom Possible Solutions Receiver Inactive for Power Check the power supply. RS485 Comm. Abnormal Check the connection line; Check whether communication address, baud rate, parity bit, stop bit set is correct; Check whether A(+) and B(-) of RS485 are reversely connected; Try to connect 120Ω terminal matching resistor.
