SML-5051W User Manual © 2019 SmartLabs Holding Ltd Proprietary and Confidential
Thank you for Choosing us The SML-5051W is a small-form and high-performance set-top box (STB) with 4K/UHD video support and is able to deliver to your home the exciting world of cutting edge interactive services. This manual contains a description of all possible features and options of SML-5051W, however your device may look slightly different from the one pictured in this document.
• • • • • • • Adapter shall be installed near the equipment and shall be easily accessible. The mains plug of adapter is used to disconnect device from power supply. The mains plug of adapter shall remain readily operable. When using the STB with a plasma TV, do not put picture on pause for more than 5 minutes, due to plasma TV screen design it could lead to display damage. The STB manufacturer is not responsible for any damage caused in such manner. The software on your STB is updated automatically.
Element Purpose Power indicator Green — STB is switched on and operates normally. IR receiver Red — STB is in stand-by mode. The internal IR receiver is accepting signals from the IR remote control. Note: the device appearance may differ from that shown in the picture.
Connecting Installation 1. Remove your STB from packaging and remove the protective tape. 2. Make sure that the place, where you are installing the STB, meets the following requirements: • Place STB on a flat surface. • Do not place the STB on slick surfaces, where there is a risk of vibration, fall or other damages of STB. • Do not mount the STB on soft surfaces, like a bed, carpet, etc.
Connecting to Internet via Wi-Fi 1. Turn on the STB and wait for it to boot. 2. Go to the "Settings" menu on the home screen. Next, "System" → "Native system settings" → "Network". 3. Select your wireless network in the list of available networks. 4. Type the password for the selected network using the on-screen keyboard (if required). 5. If there are no networks available in the list, try running the scan again. To do this, change the "Wi-Fi Off" setting to "Wi-Fi On". 6.
Switch channels Numeric keys * You can control TV after the RC setup ** RC appearance may differ from that shown in the picture. Replacing the Battery This remote is operated by a replaceable CR2032 battery. In accordance with IEC 60065:2014, the battery cover is held in the remote control case with considerable force to prevent children from accessing the battery without adult supervision. Use a screwdriver to open the cover. Be careful not to damage the battery cover or remote control case.
The remote control is supplied with a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
4. You can change the search direction, using the buttons CH- and CH+. 5. Each time you start setting up, search begins with the first code in the table.
2. Point the remote control at your TV. Press and hold the TV and OK buttons for 3 seconds. The LED on the remote control will flash twice and the remote control will switch to the setup mode. Release the TV and OK buttons. 3. Enter the four-digit setup code of your TV model from the table above. The LED will flash each time you enter a digit. 4. If you entered the code correctly, the LED will blink twice. Otherwise – once. 5. Check the buttons operation.
1. Press and hold TV and OK buttons for 3 seconds. The LED on the remote control will flash twice and the remote control will switch to the setup mode. Release the TV and OK buttons. 2. Enter the code 977. The LED will flash each time you enter a digit. After that, the LED will blink four times, and the settings will be reset to default. First Start When you switch on the STB for the first time, make sure that the STB is connected to a managed IPTV network.
4. You may remove stains from the STB’s surface with a slightly damp cloth. 5. Do not use chemical cleaner, car polish, dissolvent, aerosol, cleaning agents, abrasive powders and materials for cleaning the STB and accessories. Disposal The STB must be disposed separately from household waste. When the STB reaches its end of life, contact local authorities to learn about disposal and recycling options. The correct disposal will help prevent potential negative impact on the environment and human health.
Wi-Fi module: Standard IEEE 802.11n\ac, MIMO 2x2 Operating frequency 2.4GHz band: 2400~2483.5 MHz 5GHz band: 5150~5250 MHz & 57255850 MHz (depends on country) Antenna Gain not more than 3dBi Max. transmitting power (EIRP) not more than 18 dBm BT module: Standard BT v4.2 + BLE Operating frequency 2402–2480 MHz Antenna Gain not more than 3dBi Max. transmitting power (EIRP) not more than 8 dBm (BT class 1) The device complies with RF specifications when the device used at 20cm from your body.
are used in the device on the appropriate licenses given by its right holders. Smartlabs Holding Ltd has the appropriate licenses to use these standards. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Smartlabs Holding Ltd is able to change, improve any product described in this guide and also the guide itself without preliminary notice. ©Smartlabs Holding Ltd, 2019.
FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note that this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
