User's Manual

Page 2 of 2
Rev. 10-14-2010
Smarthome Limited Warranty – Smarthome warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be
free from defects in material & workmanship & will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by
misuse or neglect.
U.S. Patent No. 7,345,998, International patents pending © Copyright 2010
Smarthome, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845
Quick-Start Guide KeypadLinc 6-Button On/Off Switch (Dual-Band)
*Setup Modes will automatically time out after 4 minutes
Using KeypadLinc as a Responder
1) Set the Controller to Linking Mode*. (For most Controllers, press & hold an On or Scene button for 10 seconds or the Set
button for 3 seconds.)
2) Press & hold the Scene button on KeypadLinc that you would like to control until it double-beeps (10 seconds). If you
wish to control the load attached to KeypadLinc, press & hold the On button until it double-beeps (3 seconds) instead.
The Scene button’s LED should flash once, and then turn on solid. If you used the Set button, the LED will follow the
state of the load attached to KeypadLinc (On or Off)
3) Confirm that Linking was successful by tapping the button you just Linked to on the Controller
KeypadLinc should respond appropriately
FCC Compliance Statement
This device complies with FCC Rules Part 15. Operation is subject to two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference that may be received or that may cause undesired operation. The digital
circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause such interference, which
can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of
the following measures:
• Re-orient or re-locate the receiving antenna of the device experiencing the interference.
• Increase the distance between this device and the receiver.
• Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver.
• Consult the dealer or an experienced radio/TV technician.
WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Complete Instructions, Troubleshooting, and Tech Support
Owner’s Manual: http://wiki.smarthome.com/index.php?title=2487S_Manual
Call:
INSTEON Gold Support Line at 800-762-7845
Using KeypadLinc to Bridge Phases
KeypadLinc can help bridge the phases in your home and allow RF-only devices access to power line-only devices. For the
best INSTEON network performance, it is recommended that you install at least two dual-band INSTEON devices. Search for
dual-band INSTEON devices at: www.smarthome.com/dualband.
Use the following procedure to test that the phases have been bridged:
1) Install additional
dual-band INSTEON devices if they aren’t already installed
2) Start Phase Bridging Detection Mode* by tapping the Set button on KeypadLinc four times quickly
KeypadLinc should begin beeping and its LED should be solid
The load may turn on or flash
3) Check the LED behavior of the other dual-band devices to see if they are on the opposite phase
If at least one of the other dual-band device LEDs is blinking green, or is bright solid white or blue, the device is on
the opposite phase. Continue to step 4.
If none of the other dual-band devices exhibit the behavior above, they are on the same phase. Try one or both of the
following:
• Follow steps 2 and 3 with the other dual-band devices to see if they are bridging the phases
• Move a dual-band device to another location until it exhibits the desired LED behavior
4) Tap the Set button on KeypadLinc to exit Phase Bridging Detection Mode
KeypadLinc should stop beeping
Using KeypadLinc as a Controller
1) At the Responder, set it to the state you wish to activate from KeypadLinc
2) Set KeypadLinc to Linking Mode* by pressing & holding the Scene button you wish to Link until it beeps (10 seconds)
The Scene button’s LED should begin blinking
3) Press & hold the Responder’s Set button for 3 seconds
KeypadLinc should double-beep and the Scene button’s LED should stop blinking
4) Confirm that Linking was successful by tapping the button you just Linked to on KeypadLinc on, and then off
The Responder should respond appropriately
Industry Canada
Compliance Statement
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including
interference that may cause undesired
operation of the device.
Le prsent appareil est conforme aux CNR
d'Industrie Canada applicables aux
appareils radio exempts de licence.
L'exploitation est autorise aux deux
conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout
brouillage radiolectrique subi, mme si le
brouillage est susceptible d'en
compromettre le fonctionnement.