User's Manual

ManualsBrandsSmartLabs ManualsElectronics7 Day Thermostat

Quic

-Start Guide

Page 1 of 2

Rev. 09-23-2010

SMART Limited Warranty – SMART warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be free from

defects in material & workmanship & will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by misuse or

neglect.

SMART, 16542 Millikan Ave., Irvine, CA 92606, 866-883-9220

Backlit LCD

Display

Up button

(glows red)

7 Day Thermostat

Model: 4715

Heat or Cool

Demand Indicator

Mode button

Down button

(glows blue)

Installation

1) RF-only devices require at least one dual-band INSTEON product for communication. For the best INSTEON

network performance, be sure you have properly installed at least two dual-band INSTEON products.

2) Remove the old thermostat, but keep the old thermostat for reference purposes, until 7 Day Thermostat is

functioning properly

3) Remove the front cover from 7 Day Thermostat

4) Mount 7 Day Thermostat using the included hardware

5) Configure the jumpers. (See the 7 Day Thermostat Installation and Programming Guide.)

6) Refer to the chart and diagrams below for basic 1 stage cooling, 1 stage heat wiring. For other wiring

diagrams, see the Installation and Programming Guide.

Wire from the old thermostat

terminal marked

Function

Install on the new thermostat

connector marked

G or F Fan G

Y1, Y, or C Cooling Y1

W1, W or H Heating W1/O/B

Rh, R, M, Vr, A Power R

C Common C

O/B Rev. Valve W1/O/B

W2 2

Stage Heat W2

MISC1 Configurable Output #1 MISC1

MISC2 Configurable Output #2 MISC2

MISC3 Configurable Output #3 MISC3

RS+5 Remote Sensor +5vdc RS+5

RS1 Remote Sensor Signal RS1

RSGND Remote Sensor Ground RSGND

RS2 Remote Sensor Signal #2 RS2

7) Reattach the front cover to 7 Day Thermostat

Wiring Diagrams

Residential & Commercial 1 Stage Cooling, with 1

Stage Gas Heat Residential & Commercial 1 Stage Cooling, with 1

Stage Electric Heat

Controlling 7 Day Thermostat

• Tap an On or Scene button on a Linked Controller to recall the thermostat mode and set points established during Linking

• Tap an Off button on a Linked Controller to turn off the thermostat and set points established during Linking

• Tap the Bright* button on a Linked Controller to raise the set point(s) by a single degree

• Tap the Dim* button on a Linked Controller to lower the set point(s) by a single degree

*To prevent “runawa

” temperature set points, these operations onl

appl

to Controllers with Bright/Dim buttons.

Summary of content (2 pages)

PAGE 1
Quick-Start Guide Backlit LCD Display Up button (glows red) 7 Day Thermostat Model: 4715 Installation Down button (glows blue) 1) RF-only devices require at least one dual-band INSTEON product for communication. For the best INSTEON network performance, be sure you have properly installed at least two dual-band INSTEON products.
PAGE 2
FCC & Industry Canada Compliance Statement This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.