User's Manual

ManualsBrandsSmartPeak ManualsPOS EquipmentPOS Terminal

user manual

FCC Warnning:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not

explicitly approved by manufacturer could void your authority

to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2)this device must accept

any interference received, including interference that

may cause undesired operation.

Scan the qr code above, input the wi-fi

information, click to generate a new qr

code, scan the code to complete the

wi-fi connection automatically.

Scan the qr code above, download

and read the detailed instructions

and troubleshooting.

1.Packing list

SIM/SAM card：Shutdown the machine, open the battery cover, take

out battery, put SIM/SAM card chip face down and insert into the

corresponding identification card slot.

Battery：Open the battery cover, insert the battery plug into the battery

socket, Put the battery into the battery tank, place the protruding part

towards the head to close the battery cover conveniently.

Battery cover：Insert the upper end of the battery cover into the

machine,and then fasten the clasp downward.

Note：1. Before installing the battery, please check the battery

appearance without any damage.

2. If the battery cover is held up, please turn the battery to install.

Power on：Long press the power button for 3 seconds, the backlight of

the screen lights up, and the terminal is activated.

Close：Long press the power button for 3 seconds, the POS machine

enters the shutdown process.

Charging：After installing the battery and closing the battery cover,

connect the Micro-USB interface of POS device.Connect the adapter at

one end and start charging after turning on the power.

For detailed instructions and common fault analysis, please scan the

QR code below.

2.Installation instructions

3. Product operation

4.Matters needing attention

4.1.Only applicable to 5V chargers.

4.2.Before connecting AC power, please check the power cord and power

adapter for damage.If there is, it can no longer be used.

4.3.The equipment should be placed on a stable platform indoors. Do

not place it in direct sunlight, high temperature, humidity or dusty place.

Please keep away from liquid.

4.4.Do not insert any foreign object into any interface of the device, which

may seriously damage the device;

4.5.If equipment failure, please contact POS after-sales service personnel.

Users are not allowed to repair the equipment without authorization.

4.6.Scanning is only available for devices with a camera version.

4.7.The software of different dealers is different and the operation is

different. The above operations are for reference only.

Name Quantity

P90 wireless POS terminal

User manual

Battery

Handwritten pen（optional）

Cable

Power adapter

Reflective mirror structure（optional）

No.

1 1

5.List of hazardous substances

Part name

Shell

Circuit board

Power

Cable

Packaging

Battery

This form is prepared in accordance with SJ/T 11364

：Indicates that the content of harmful substances in all uniform materials of the component is below the limit specified in GB/T 26572.

：Indicates that the content of the hazardous substance in at least one uniform material of the component exceeds the limit specified in GB/T 26572.

PS：1.Most parts of the product are made of harmless and environment-friendly materials, the parts containing harmful substances cannot be

replaced due to the limitation of global technology development level.

2.Environmental data for reference are obtained by testing in the normal use and storage environment required by the product, such as

humidity and temperature.

Hg Cd Cr(VI) PBDEPBB

Harmful substances

POS TerminalPOS Terminal

Model: P90

Summary of content (2 pages)

PAGE 1
FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 2
Specific Absorption Rate (SAR) information: This POS Terminal meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.