Operating Guide

ManualsBrandssmartpond ManualsPond KitsACFK

Container Fountain Kit

MODEL/MODELO #ACFK

PACKAGE CONTENTS

WARNINGS AND CAUTIONS

WARNING

• Risk of electrical shock. This pump is supplied with a grounding conductor and grounding–type

attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly

grounded, grounding-type receptacle (GFCI).

• Do not exceed the voltage shown on the pump.

• Always disconnect pump from the power source before beginning any maintenance or work on the

pump.

• Inspect cord for damage before installation and/or maintenance. Replace the entire pump assembly if

damage is found.

• Do not remove the grounding pin from the power cord plug.

• To reduce the risk of electric shock, use only on portable, self-contained fountains no larger than 5 ft. in

any dimension.

• Risk of electrical shock – This pump has not been investigated for use in swimming pools or marine

areas.

Part Description Quantity

A Pump 1

B Base plate 1

C Filter block 1

D Filter cover 1

E Extension tubes 1

F Waterspray nozzle 1

G Waterbell nozzle insert 1

H Trumpet nozzle insert 1

I Lower fountain head nozzle 1

J Adapter (with o-ring) 1

Questions, problems, missing parts? Before returning

to your retailer, call our customer service department at

1-866-869-5300, 8 a.m.-6 p.m., EST, Monday-Friday, or

email us at customercare@smart-pond.com.

F G H I J

REMINDER

CALL 1-866-869-5300

BEFORE RETURNING TO STORE.

Summary of content (6 pages)

PAGE 1
Container Fountain Kit MODEL/MODELO #ACFK REMINDER CALL 1-866-869-5300 BEFORE RETURNING TO STORE. Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-869-5300, 8 a.m.-6 p.m., EST, Monday-Friday, or email us at customercare@smart-pond.com.
PAGE 2
CAUTION • This pump has been evaluated for use with water only. • Use a proper power source as indicated on the pump label. • Keep the cord away from high temperatures or other heat sources. • Avoid using the pump when water temperatures fall below 41° F. • Do not use the pump in water exceeding 86° F. • Do not pump heated liquids. • Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling. • Operate in freshwater only.
PAGE 3
. Choose a fountain head for the desired water effect, and assemble your choice as shown in Fig. 3. F E G H I I E E Fig. 3 4. Choose a container for your fountain kit. Fig. 4 Fig. 4 5. If the container is not already watertight, use a plastic liner. Or if a clay pot is used, spray the inside of the pot with a clear acrylic sealant. Be sure to use a sealant that is safe for clay pots. Wait 24 hours for the sealant to dry before filling the container with water. Fig. 5 Liner Fig. 5 6.
PAGE 4
7. Select a spot on the container wall that is the least visible from normal viewing for the cord exit. Create the hole, using a drill with appropriate bit capable of boring through the container material and large enough so the plug head can pass through. Fig. 7 Note: Appropriate safety equipment should be used. Fig. 7 8. Seal up the hole along with any other drainage holes in the container. Press plumbers putting into the hole and seal it with silicone caulk.
PAGE 5
CARE AND MAINTENANCE • Regular cleaning of the pump may be necessary depending upon the environment in which it is operated. Clean the pump when it is visibly soiled or when a drop in performance is detected. • Before cleaning, always disconnect the pump from the power source. • Remove all parts from the pump and clean in warm, soapy water. • Disassemble the front cover and remove the impeller cover to expose the impeller assembly.
PAGE 6
LIMITED WARRANTY All pumps and electrical products are warranted to the user against defective material and workmanship, under normal working conditions. This warranty period begins on the date of purchase by the original purchaser.