SR630n User Manual VER: 1.
User Manual Contents 1 Safety Precautions ............................................................................................. 1 2 Overview ............................................................................................................ 2 3 2.1 Application ............................................................................................. 2 2.2 Features ................................................................................................ 3 2.
User Manual 5.3 5.4 5.5 5.2.5 NAT ........................................................................................... 61 5.2.6 Security ..................................................................................... 65 5.2.7 Parental Control ........................................................................ 68 5.2.8 Quality of Service...................................................................... 70 5.2.9 Routing .......................................................
User Manual 5.6 6 5.5.1 Diagnostics ............................................................................. 126 5.5.2 Fault Management .................................................................. 127 Management...................................................................................... 128 5.6.1 Settings ................................................................................... 129 5.6.2 System Log .....................................................................
User Manual 1 Safety Precautions Read the following information carefully before operating the device. Please follow the following precaution items to protect the device from risks and damage caused by fire and electric power: Use volume labels to mark the type of power. Use the power adapter that is packed within the device package. Pay attention to the power load of the outlet or prolonged lines. An overburden power outlet or damaged lines and plugs may cause electric shock or fire accident.
User Manual 2 Overview The xDSL Router integrates wireless LAN, USB, and VoIP service into one unit. It is designed to provide a simple and cost-effective xDSL Internet connection for a private Ethernet and 802.11b/802.11g/802.11n wireless network. The Router combines high-speed xDSL Internet connection, Ethernet uplink, IP routing for the LAN and wireless connectivity in one package.
User Manual 3G WAN service 2.2 Features User-friendly GUI for web configuration Several pre-configured popular games. Just enable the game and the port settings are automatically configured.
User Manual DSL router is targeted at the following platforms: DSL modems, wireless access points and bridge. 2.3 Standards Compatibility and Compliance Support application level gateway (ALG) ITU G.992.1 (G.dmt) ITU G.992.2 (G.lite) ITU G.994.1 (G.hs) ITU G.992.3 (ADSL2) ITU G.992.5 (ADSL2+) ITU G.993.1 (VDSL) ITU G993.2 (VDSL2) 3G (WCDMA, CDMA2000, TD-SCDMA) ANSI T1.413 Issue 2 IEEE 802.3 IEEE 802.3u IEEE 802.11b IEEE 802.11g IEEE 802.
User Manual 3 Hardware Description and Installation Note: The figures in this document are for reference only. 3.1 Hardware Description 3.1.1 Front Panel Figure 1 Front panel The following table describes the indicators on the front panel. Indicator Color Status Description On Green Power Red DSL Green Blink Off The device is powered off. The device is initiating. Blink The software is upgrading. On DSL link has established. Blink The DSL line is training.
User Manual Indicator Color Status Description established. Blink WLAN Green No signal is detected. On WLAN is enabled. Blink Off On WPS Green Blink Off TEL1/2 Green Data is being transmitted. Off Data is being transmitted through the wireless interface. WLAN is disabled. Connection succeeds under Wi-Fi Protected Setup. Negotiation is in progress under Wi-Fi Protected Setup. Wi-Fi Protected Setup is disabled. Off No FXS signal is detected.
User Manual Figure 2 Rear panel Figure 3 Side panel The following table describes the interfaces and the buttons. Interface Description DSL TEL1/2 LAN 4~1 WAN Reset USB1/2 RJ-11 port. Connect the router to DSL connector or splitter through telephone cable. RJ-11 FXS port, using the telephone cable to connect the telephone set. RJ-45 port, for connecting the router to a PC or another network device. For connecting Ethernet cable to provide Ethernet uplink.
User Manual 3.2.1 Choosing the Best Location for Wireless Operation Many environmental factors may affect the effective wireless function of the DSL Router. If this is the first time that you set up a wireless network device, read the following information: The access point can be placed on a shelf or desktop, ideally you should be able to see the LED indicators in the front, as you may need to view them for troubleshooting.
User Manual Figure 4 Connecting the DSL router Note: If you use 3G WAN service, connect the 3G USB data card to the USB port of the router. If you use the Ethernet uplink, connect the WAN interface that is defined to the Internet with Ethernet cable. The xDSL uplink, 3G WAN service, and Ethernet uplink can not coexist.
User Manual 4 PC Network Configuration and Login 4.1 PC Network Configuration Each network interface on the PC should either be configured with a statically defined IP address and DNS address, or be instructed to automatically obtain an IP address using the network DHCP server. DSL router provides a DHCP server on its LAN and it is recommended to configure your LAN to automatically obtain its IP address and DNS server IP address.
User Manual Figure 5 IP and DNS configuration TCP/IP configuration steps for Windows XP are as follows: Step 1 Choose Start > Control Panel > Network Connections. Step 2 Right-click the Ethernet connection icon and choose Properties. Step 3 On the General tab, select the Internet Protocol (TCP/IP) component and click Properties. Step 4 The Internet Protocol (TCP/IP) Properties window appears.
User Manual Step 5 Select the Obtain an IP address automatically radio button. Step 6 Select the Obtain DNS server address automatically radio button. Step 7 If you want to set the IP address and subnet mask manually, you can set the IP address and subnet mask of the computer to 192.168.1.x and 255.255.255.0 respectively. The range for x is from 2 to 254. Step 8 Click OK to save the settings. 4.
User Manual Figure 6 Login page After logging in to the DSL router as a super user, you can query, configure, and modify all the settings, and diagnose the system 5 Web-Based Management This chapter describes how to use Web-based management of the DSL router, which allows you to configure and control all of DSL router features and system parameters in a user-friendly GUI. 5.
User Manual 5.1.1 Summary Choose Device Info > Summary, and the following page appears.
User Manual This page displays the device information such as the board ID, software version, and the information of your WAN connection such as the upstream rate and the LAN address. 5.1.2 WAN Choose Device Info > WAN and the following page appears.
User Manual This page displays the information of the WAN interface, such as the connection status, and the IP address. 5.1.3 Statistics 5.1.4 LAN Choose Device Info > Statistics > LAN and the following page appears. In this page, you can view the statistical information about the recevied and transmitted data packets of the Ethernet and wireless interfaces. Click Reset Statistics to restore the values to zero and recount them. 5.1.
User Manual In this page, you can view the statistical information about the recevied and transmitted data packets of the WAN interface. Click Reset Statistics to restore the values to zero and recount them. 5.1.6 xTM Choose Device Info > Statistics > xTM and the following page appears. In this page, you can view the statistical information about the recevied and transmitted data packets at the xTM interfaces. Click the Reset button to restore the values to zero and recount them. 5.1.
User Manual 18
User Manual In this page, you can view the statistical information about the recevied and transmitted data packets of the xDSL interfaces. Click xDSL BER Test to test the xDSL Bit Error Rate. Click Reset Statistics to restore the values to zero and recount them. xDSL BER Test Click xDSL BER Test to perform a bit error rate (BER) test on the DSL line. The test page is as follows: The Tested Time (sec) can be 1, 5, 10, 20, 60, 120, 180, 240, 300, or 360. Select a time in the drop-down list and click Start.
User Manual When the ADSL BER test completes, the following page appears. Note: If the BER reaches e-5, you cannot access the Internet. 5.1.8 Route Choose Device Info > Route and the following page appears. In this page, you can view the route table information.
User Manual 5.1.9 ARP Choose Device Info > ARP and the following page appears. In this page, you can view the MAC address and IP address information of the device connected to the router. 5.1.10 DHCP Choose Device Info > DHCP and the following page appears. In this page, you can view the host name, the IP address assigned by the DHCP server, the MAC address this is corresponding to the IP address, and the DHCP lease time. 5.
User Manual 5.2.1 Layer2 Interface 5.2.1.1 ATM Interface Choose Advanced Setup > Layer2 Interface > ATM Interface . In this page, you can add or remove to configure DSL ATM Interfaces.
User Manual Click Add to add ATM Interface and the following page appears.
User Manual In this page, you can enter this PVC (VPI and VCI) value, and select DSL link type (EoA is for PPPoE, IPoE, and Bridge.), encapsulation mode, service category. VPI (Virtual Path Identifier): The virtual path between two points in an ATM network, and its valid value is from 0 to 255. VCI (Virtual Channel Identifier): The virtual channel between two points in an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known protocols).
User Manual In this page, you can select scheduler for queues of equal precedence and enter the queue value. Click Apply/Save to save configuration. 5.2.1.3 ETH Interface Choose Advanced Setup > Layer2 Interface > ETH Interface, and the following page appears. In this page, you can add or remove to configure ETH WAN Interfaces. Click Add and the following page appears.
User Manual In this page, you can select a ETH port. Click Apply/Save to save configuration. Note: If ETH Interface is selected, there are two WAN service types (PPPoE and IPoE). 5.2.2 WAN Service Choose Advanced Setup > WAN Service, and the following page appears. In this page, you are allowed to add, remove, or edit a WAN service. Note: If PTM Interface is selected, there are three WAN service types: PPP over Ethernet (PPPoE), IP over Ethernet, Bridging.
User Manual Step1 In the Wide Area Network (WAN) Service Setup page, click the Add button to display the following page. (At first, you must add a proper ATM or PTM interface for this WAN service.) Step2 In this page, you can select a ATM Interface for the WAN service. After selecting the ATM interface, click Next to display the following page.
User Manual Step3 In this page, select the WAN service type to be PPP over Ethernet (PPPoE). Click Next to display the following page.
User Manual Step4 In this page, you can modify the PPP username, PPP password, PPPoE service name and authentication method. PPP Username: The correct user name provided by your ISP. PPP Password: The correct password provided by your ISP. PPPoE Service Name: If your ISP provides it to you, please enter it. If not, do not enter any information. Authentication Method: The value can be AUTO, PAP, CHAP, or MSCHAP. Usually, you can select AUTO. Enable Fullcone NAT:.
User Manual does not stop, unless the modem is powered off and DSLAM or uplink equipment is abnormal. PPP IP extension: If you want to configure DMZ Host, you should enable it first. Use Static IPv4 Address: If this function is disabled, the modem obtains an IP address assigned by an uplink equipment such as BAS, through PPPoE dial-up. If this function is enabled, the modem uses this IP address as the WAN IP address. Enable PPP Debug Mode:Enable or disable this function.
User Manual Step7 In this page, you can obtain the DNS server addresses from the selected WAN interface. Click Next, and the following page appears.
User Manual Step8 In this page, it displays the information about the PPPoE settngs. Click Apply/Save to save and apply the settings. 5.2.2.2 Adding a MER (IPoE) WAN service This section describes the steps for adding the MER WAN service. Step1 In the Wide Area Network (WAN) Service Setup page, click the Add button to display the following page. (At first, you must add a ATM or PTM interface for this WAN service.) Step2 Select an ATM Interface, and then click Next to display the following page.
User Manual Step3 In this page, select the WAN service type to be IP over Ethernet, enter the service description for this service. After finishing setting, click Next to display the following page.
User Manual Step4 In this page, you may modify the WAN IP settings. You may select obtain an IP address automatically or manually enter the IP address provided by your ISP. Click Next and the following page appears. Note: If selecting Obtain an IP address automatically, DHCP will be enabled for PVC in MER mode. If selecting Use the following Static IP address, please enter the WAN IP address, subnet mask and gateway IP address.
User Manual Step5 In this page, you can set the network address translation settings,for example, enabling NAT, enabling firewall, and enabling IGMP multicast. After finishing setting, click Next and the following page appears. Step6 In this page, select a preferred WAN interface as the system default gateway and then click Next to display the following page.
User Manual Step7 In this page, you can obtain the DNS server addresses from the selected WAN interface. After finishing setting, click Next to display the following page.
User Manual Step8 In this page, it displays the information about the IPoE settngs.Click Apply/Save to save and apply the settings. 5.2.2.3 Adding a PPPoA WAN service This section describes the steps for adding the PPPoA WAN service. Step1 Choose Advanced Setup > Layer2 Interface > ATM Interface to dsipaly the DSL ATM Interface Configuration page. In this page, you need to add a PVC for PPPoA mode. Click the Add button in the DSL ATM Interface Configuration page to display the following page.
User Manual Step2 Select the DSL link type to be PPPoA, and select the encapsulation mode to be VC/MUX (according to the uplink equipment). After finishing setting, click the Apply/Save button to apply the setings. Step3 Choose WAN Service and click Add to display the following page.
User Manual Step4 Select the proper interface for the WAN service, and then click Next to display the following page. Step5 In this page, you may modify the service description. Click Next to display the following page.
User Manual PPP Username: The correct user name provided by your ISP. PPP Password: The correct password provided by your ISP. Authentication Method: The value can be AUTO, PAP, CHAP, or MSCHAP. Usually, you can select AUTO. Enable Fullcone NAT:. NAT is one where all requests from the same internal IP address and port are mapped to the same external IP address and port. Furthermore, any external host can send a packet to the internal host, by sending a packet to the mapped external address.
User Manual dial-up. If this function is enabled, the modem uses this IP address as the WAN IP address. Enable PPP Debug Mode:Enable or disable this function. Enable IGMP Multicast Proxy: If you want PPPoE mode to support IPTV, enable it. Step6 In this page, you can enter the PPP username and PPP password provided by your ISP. Select the authentication method according to your requirement. After finishing setting, click Next to display the following page.
User Manual Step8 In this page, you can obtain the DNS server addresses from the selected WAN interface. After finishing setting, click Next to display the following page.
User Manual Step9 In this page, it displays the information about the PPPoA settngs.Click Apply/Save to apply the settings. You can modify the settings by clicking the Back button if necessary. 5.2.2.4 Adding an IPoA WAN service This section describes the steps for adding the IPoA WAN service. Step1 Choose Advanced Setup > Layer2 Interface > ATM Interface to dsipaly the DSL ATM Interface Configuration page. In this page, you need to add a PVC for IPoA mode.
User Manual Step2 Select the DSL link type to be IPoA, and select the encapsulation mode to be LLC/SNAP-ROUTING (according to the uplink equipment). After finishing setting, click the Apply/Save button to save the settings. Step3 Choose WAN Service and click Add to display the following page.
User Manual Step4 Select the proper interface for the WAN service ,and then click Next to display the following page. Step5 In this page, you may modify the service description. Click Next to display the following page.
User Manual Step6 In this page, enter the WAN IP address, the WAN subnet mask, and primary DNS server provided by your ISP and then click Next to display the following page. In this page, Network Address Translation (NAT) allows you to share one Wide Area Network (WAN) IP address for multiple computers on your Local Area Network (LAN). If you do not want to enable NAT, and wish the user of modem to access the Internet normally, you need to add a route on the uplink equipment.
User Manual Step7 After finishing setting, click Next to display the following page. Step8 In this page, select a preferred WAN interface as the system default gateway and then click Next to display the following page.
User Manual Step9 In this page, you can obtain the DNS server addresses from the selected WAN interface. After finishing setting, click Next to display the following page. Step10 In this page, it displays the information about the IPoA settngs. Click Apply/Save to save and apply the settings. You can modify the settings by clicking the Back button if necessary. 5.2.2.5 Adding a Bridge WAN service This section describes the steps for adding the Bridge WAN service.
User Manual Step2 Select the proper ATM Interface and then click Next to display the following page.
User Manual Step3 In this page, you can select the WAN service type, and modify the service description for this service. After finishing setting, click Next to display the following page.
User Manual Step4 In this page, it displays the information about the bridge settngs. Click Apply/Save to save and apply the settings. You can modify the settings by clicking the Back button if necessary. 5.2.3 3G WAN Service Choose Advanced Setup > 3G WAN Service , and the following page appears. This page is used to configure 3G connection. If you want to access the Internet through 3G connection, a 3G network card is required. Connect the 3G network card to the USB interface of the Router.
User Manual Enable PIN protect: If you enable it, you need to enter the PIN code when rebooting or inserting the card to the USB interface. Unlock with PIN code: If you disable it, you need to enter PIN code when using 3G. Unlock with PUK & PIN: If you disable it, you need to enter PUK code when failing to enter the PIN code for 3 times. Change PIN code: Choose it to change the PIN code. After proper settings, click Submit to take the settings in to effect.
User Manual In this page, you are allowed to configure the settings of the 3G USB modem. Enable USB Modem: If you want to access the Internet through the 3G network card, you must enable the USB modem. User Name: Username provided by your 3G ISP. Password: Password provided by your 3G ISP. Authentication Method: Select a proper authentication method in the dropdown list. You can select Auto, PAP, CHAP, or MSCHAP. APN: APN (Access Point Name) is used to identify the service type.
User Manual Idle time (in sec.): If no traffic for the preset time, the 3G will disconnect automatically. Net Select: Select the 3G network that is available.You may select EVDO, WCDMA, CDMA2000, TD-SCDMA, GSM, or Auto. Dial on demand: Within the preset minutes, if the modem does not detect the flow of the user continuously, the modem automatically stops the 3G connection. Once it detects the flow (like access to a webpage), the modem restarts the 3G dialup. Dail Delay (in sec.
User Manual connection. When the DSL WAN connection starts to perform dial-up, the 3G connection will be disconnected. If the DSL WAN connection has established, you may manually to perform 3G dial-up, and then the DSL WAN connection will be disconnected. 5.2.4 LAN Configuration Choose Advanced Setup > LAN, and the following page appears.
User Manual In this page, you can configure an IP address for the DSL router, enable IGMP snooping, enable or disable the DHCP server, edit the DHCP option, configure the DHCP advanced setup and set the binding between a MAC address and an IP address. Configuring the Private IP Address for the DSL Router In this page, you can modify the IP address of the device. The preset IP address is 192.168.1.1.
User Manual Configuring the DHCP Server If you enable the DHCP sever, the clients will automatically acquire the IP address from the DHCP server. If the DHCP server is disabled, you need to manually set the start IP address, end IP address and the lease time for the clients in the LAN. Editing the DHCP Option60 Click the Edit DHCP Option60 button in the Local Area Network (LAN) Setup page to display the DHCP Option60 Setup page. In this page, you can add, edit or delete the DHCP60 options.
User Manual DHCP Advanced Setup Click the DHCP Advance Setup button in the Local Area Network (LAN) Setup page to display the following page. In this page, you can enable or disable DHCP for every LAN interface. Configuring the DHCP Static IP Lease List The lease list of static IP address can reserve the static IP addresses for the hosts with the specific MAC addresses.
User Manual In this page, enter the MAC address of the LAN host and the static IP address that is reserved for the host, and then click the Apply/Save button to apply the settings. Configuring the Second IP Address and Subnet Mask for a LAN Interface In the Local Area Network (LAN) Setup page, you are allowed to set the second IP address and the subnet mask for a LAN interface.
User Manual In this page, you can set an IP address for the DSL IPv6 router, enable the DHCPv6 server, enable RADVD and enable the MLD snooping function. Enable DHCPv6 Server: WIDE-DHCPv6 is an open-source implementation of dynamic host configuration protocol for IPv6 (DHCPv6) originally developed by the KAME project. The implementation mainly complies with the following standards: RFC3315, RFC3319, RFC3633, RFC3646, RFC4075, RFC 4272 etc.
User Manual Enable RADVD: The router advertisement daemon (RADVD) is run by Linux or BSD systems acting as IPv6 routers. It sends router advertisement messages, specified by RFC2461, to a local Ethernet LAN periodically and when requested by a node sending a router solicitation message. These messages are required for IPv6 stateless auto-configuration.
User Manual Use interface: Select an interface that you want to configure. Select a Service: Select a proper service in the drop-down list. Custom Server: Enter a new service name to establish a user service type. Server IP Address: Assign an IP address to virtual server. External Port Start: When selecting a service, the port number will automatically be displayed. You can modify it if necessary. External Port End: When selecting a service, the port number will automatically be displayed.
User Manual Internal Port End: When selecting a service, the port number will automatically be displayed. You can modify it if necessary. Step 2 5.2.5.2 After finishing setting, click Save/Apply to save and apply the settings. Port Triggering Some applications need some ports to be opened in the firewall for the remote access. When an application initializes a TCP/UDP to connect to a remote user, port triggering dynamically opens the open ports of the firewall.
User Manual Use interface: Select an interface that you want to configure. Select an application: Select a proper application in the drop-down list. Custom application: Manually define an application. Trigger port Start: The start port number that LAN uses to trigger the open port. Trigger port End: The end port number that LAN uses to trigger the open port. Trigger Protocol: Select the application protocol. You may select TCP/UDP, TCP, or UDP. Open Port Start: The start port number that is opened to WAN.
User Manual You can use a single port number, several port numbers separated by commas, port blocks consisting of two port numbers separated by a dash, or any combination of these, for example 80, 90-140, 180. 5.2.5.3 DMZ Host DMZ allows all the ports of a PC on your LAN to be exposed to the Internet. Set the IP address of the PC to be DMZ host, so that the DMZ host will not be blocked by firewall. Choose Advanced Setup > NAT > DMZ host to display the following page.
User Manual Click Add Firewall, and the following page appears. name: The name of firewall. interface: You can select LAN or WAN from the drop-down list. type: You can select IN or OUT from the drop-down list. defaultaction: You can select Permit or Drop from the drop-down list. Click Add Rule, and the following page appears. enabled: Select the check box to enable the firewall rule. Protocol: You can select UDP, TCP, or ICMP from the drop-down list.
User Manual destIPAddress: The destination IP address. destMask: The destination subnet mask. destStartPort: The destination start port. destEndPort: The destination end port. After finishing setting, click Save&Apply to save and activate the rule. MAC Filtering Setup In some cases, you may want to manage Layer2 MAC address to block or permit a computer within the home network. When you enable MAC filter rules, the DSL router serves as a firewall that works at layer 2.
User Manual In this page, you can add or remove the MAC filtering rule. You may change the MAC filtering policy from FORWARDED to BLOCKED by clicking the Change Policy button. Click the Add button to display the following page. Protocol Type: Select the proper protocol type. Destination MAC Address: Enter the destination MAC address. Source MAC Address: Enter the source MAC address. Frame Direction: The direction of transmission frame.
User Manual This page is used to control the time restriction to a special LAN device that connects to the DSL router. In this page, se the user name and configure the time settings. After finishing setting, click the Apply/Save button to save and apply the settings. Url Filter Click Advanced Setup > Parental Control > Url Filter, and the following page appears. Thisp age is used to prevent the LAN users from accessing some Websites in the WAN.
User Manual In this page, enter the URL address and its corresponding port number. For example, enter the URL address http://www.google.com and the port number 80, and then click the Apply/Save button. See the following figure: 5.2.8 Quality of Service Enabling QoS Choose Advance Setup > Quality of Service and the following page appears.
User Manual Select Enable QoS to enable QoS and configure the default DSCP mark. In this page, enable the QoS function and select the default DSCP mark. After finishing setting, click Apply/Save to save and apply the settings. Note: If the Enable Qos checkbox is not selected, all QoS will be disabled for all interfaces. The default DSCP mark is used to mark all egress packets that do not match any classification rules.
User Manual In this page, you can enable, add or remove a QoS rule. Note: The lower integer value for precedence indicates the higher priority. Click the Add button to display the following page. Name: Enter the name of QoS queue.
User Manual Enable: Enable or disable the QoS queue. Interface: Select the proper interface for the QoS queue. After finishing setting, click Apply/Save to save and apply the settings. QoS Classification Choose Advanced Setup > Quality of Service > Qos Classification and the following page appears. In this page, you can enable, add or remove a QoS classification rule. Click the Add button to display the following page.
User Manual 5.2.9 Routing Default Gateway Choose Advanced Setup > Routing > Default Gateway, and the following page appears.
User Manual In this page, you can modify the default gateway settings. Select a proper WAN interface in the drop-down list of Selected WAN Interface as the system default gateway. After finishing setting, click Apply/Save to save and apply the settings. Static Route Choose Advanced Setup > Routing > Static Route and the following page appears. In this page, you can add or remove a static routing rule. Click the Add button to display the following page.
User Manual IP Version: Select the IP version. Destination IP address/prefix length: Enter the destination IP address. Interface: select the proper interface for the rule. Gateway IP Address: The next-hop IP address. Metric: The metric value of routing. After finishing setting, click Apply/Save to save and apply the settings. Policy Routing Choose Advanced Setup > Routing > Policy Routing and the following page appears. In this page, you can add or remove a static policy rule.
User Manual In this page, enter the policy name, source IP and default gateway, and select the physical LAN port and interface. After finishing setting, click Apply/Save to save and apply the settings. RIP Choose Advanced Setup > Routing > RIP and the following page appears. In this page, if you want to configure an individual interface, select the desired RIP version and operation, and then select the Enabled checkbox for the interface.
User Manual 5.2.10 DNS DNS Server Choose Advanced Setup > DNS > DNS Server and the following page appears. In this page, you can select a DNS server interface from the available interfaces, manually enter the DNS server addresses, or obtain the DNS address from a WAN interface. After finishing setting, click Apply/Save to save and apply the settings. Dynamic DNS Choose Advanced Setup > DNS > Dynamic DNS and the following page appears.
User Manual In this page, you are allowed to modify the DDNS settings. Click the Add button to display the following page. D-DNS provider: Select a proper DDNS server in the drop-down list. Hostname: It is the domain name and it can be modified. Interface: The interface that the packets pass through on the DSL router. Username: Enter the username for accessing the DDNS management interface. Password: Enter the password for accessing the DDNS management interface.
User Manual In this page, you can set the DSL settings. Usually, you do not need to modify the factory default settings. After finishing setting, click Apply/Save to save and apply the settings. 5.2.12 UPnP Choose Advanced Setup > UPnP and the following page appears.
User Manual In this page, you can enable or disable the UPnP function. After finishing setting, click Apply/Save to save and apply the settings. 5.2.13 DNS Proxy Choose Advanced Setup > DNS Proxy and the following page appears. In this page, you can enable or disable the DNS proxy function. After enabling the DNS proxy function, enter the host name of the broadband router and the domain name of the LAN network, and then click Apply/Save to save and apply the settings. 5.2.
User Manual In this page, you can enable or disable the printer server. After finishing setting, click Apply/Save to save and apply the settings. 5.2.15 DLNA Choose Advanced Setup > DLNA and the following page appears. In this page, select the Enable on-board digital media server check box, and the following page appears. In this page, enter the media library path to run digital media server.
User Manual 5.2.16 Packet Acceleration Choose Advanced Setup > Packet Acceleration and the following page appears. In this page, you can enable packet flow accelerator. 5.2.17 Storage Service Storage Device Info Choose Advanced Setup > Storage Service > Storage Device Info and the following page appears. This page is used to display the information of the storage device that connects to the DSL router.
User Manual 5.2.18 Interface Grouping Choose Advanced Setup > Interface Grouping and the following page appears. Interface grouping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with the appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the default group. Only the default group has IP interface.
User Manual In this page, please follow the on-screen configuration steps to configure the parameters of the interface grouping. After finishing setting, click Apply/Save to save and apply the settings. 5.2.19 IP Tunnel 5.2.19.1 IPv6 in IPv4 Choose Advanced Setup > IP Tunnel > IPv6inIPv4 and the following page appears. The default value is IPv6 in IPv4 information.
User Manual Click Add and the following page appears. In this page, you can add a new tunnel. IPv4 Mask Length: The value is 0 ~ 32. 6rd Prefix with Prefix Length: prefix/length, such as: 2002::/64. After proper settings, click Apply/Save and the following page appears.
User Manual 5.2.19.2 IPv4 in IPv6 Choose Advanced Setup > IP Tunnel > IPv4inIPv6 and the following page appears. Click Add and the following page appears. In this page, you can add a new tunnel of IPv4 in IPv6. 5.2.20 IPSec Choose Advanced Setup > IPSec and the following page appears.
User Manual In this page, you can add or remove the IPSec tunnel connections. Click the Add button to display the following page.
User Manual In this page, set the parameters such as the IPSec connection name, tunnel mode, and remote IPSec gateway address. If you need to configure the advanced settings of this IPSec tunnel connection, please click the Show Advanced Settings button to display the other parameters. After finishing setting, click Apply/Save to save and apply the settings.
User Manual 5.2.21 Certificate Local Choose Advanced Setup > Certificate > local and the following page appears. In this page, you can acquire the local certificate by creating a certificate request or importing a certificate. You may also create or remove a certificate. Creating a New Certificate Request Click the Create Certificate Request button to display the following page. In this page, please set the following parameters. Certificate name: Set the certificate name.
User Manual pathnames in the common name. Do not use wildcard characters such as * or ?, and do not use an IP address. Organization Name: The name of the organization to which the entity belongs (such as the name of a company). State/Province Name: This is the name of the state or province where your organization's head office is located. Please enter the full name of the state or province.
User Manual In this page, paste the signed certificate, and then click the Apply button. A new certificate is created. Importing an Existing Local Certificate To import an existing certificate, click the Import Certificate button to display the following page.
User Manual In this page, paste the certificate and the private key. Finally, click the Apply button to import the certificate. Trusted CA Choose Advanced Setup > Certificate > Trusted CA and the following page appears.
User Manual In this page, you may import or remove a CA certificate. Click the Import Certificate button to display the following page. In this page, enter the certificate name and paste the certificate content. Finally, click the Apply button to import the certificate. 5.2.22 Power Management Choose Advanced Setup > Power Management and the following page appears. This page allows control of Hardware modules to evaluate power consumption. Use the control buttons to select the desired option.
User Manual After proper configurations, click Apply to take the configurations effect. 5.2.23 Multicast Choose Advanced Setup > Multicast and the following page appears.
User Manual In this page, you can configure the multicast parameters. After finishing setting, click Apply/Save to save and apply the settings. 5.
User Manual 5.3.1 Basic Settings Choose Wireless > Basic to display the following page. In this page, the figure in the right area is 2-dimensional code. It includes the wireless SSID and password. You can obtain the wireless SSID and password through scanning this figure.
User Manual This page allows you to configure the basic features of the wireless LAN interface. Enable Wireless: Enable or disable the wireless function. Hide Access Point: if you want to hide any access point for your router, select this option, and then a station cannot obtain the SSID through the passive scanning. Clients Isolation: When many clients connect to the same access point, they can access each other.
User Manual This page allows you to configure the security features of the wireless LAN interface. In this page, you can configure the network security settings by the Wi-Fi Protected Setup (WPS) method or setting the network authentication mode.
User Manual There are 2 primary methods used in the Wi-Fi Protected Setup: PIN entry, a mandatory method of setup for all WPS certified devices. – Enter STA PIN: If you select it, you need to enter the station PIN from – Use AP PIN: The PIN is generated by AP. client. Push button configuration (PBC), an actual push button on the hardware or through a simulated push button in the software. (This is an optional method on wireless client).
User Manual - Open Mode Select SSID: Select a SSID for configuring the security settings. Network Authentication: Select the Open mode. WEP Encryption: Enable or disable WEP encryption. After enabling this function, you can set the encryption strength, current network key, and network keys. Encryption Strength: You can set 64-bit or 128-bit key. Current Network Key: The current key that you use. Network Key1/2/3/4: Set the network key.
User Manual - Shared Mode The parameters’ description of shared mode, please refer to the Open Mode. - 802.1x Select SSID: Select a SSID for configuring the security settings. Network Authentication: Select the 802.1X in the drop-down list.
User Manual RADIUS Server IP Address: Enter the IP address of the RADIUS server. RADIUS server is used to authenticate the hosts on the wireless network. RADIUS Port: The port number that the RADIUS server uses. The default port number is 1812. You may change it according to the server setting. RADIUS Key: Set the RADIUS key for accessing the RADIUS server. WEP Encryption: You can only select Enabled. Encryption Strength: You can set 64-bit or 128-bit key. Current Network Key: The current key that you use.
User Manual - WPA-PSK Mode Select SSID: Select a SSID for configuring the security settings. Network Authentication: Select the WPA-PSK mode. WPA/WAPI passphrase: The key for WPA encryption. Click the Click here to display button to display the current key. The default key is 87654321. WPA Group Rekey Interval: Setting the interval for renewing key. WPA/WAPI Encryption: You may select AES, or TKIP+AES. - WPA2 Mode Select SSID: Select a SSID for configuring the security settings.
User Manual WPA2 Preauthentication: Enable or disable pre-authentication. Network Re-auth Interval: Set the network re-auth interval. WPA Group Rekey Interval: Setting the interval for renewing key. RADIUS Server IP Address: Enter the IP address of the RADIUS server. RADIUS server is used to authenticate the hosts on the wireless network. RADIUS Port: The port number that the RADIUS server uses. The default port number is 1812. You may change it according to the server setting.
User Manual The parameters’ description of Mixed WPA2/WPA mode, please refer to the WPA2 mode. - Mixed WPA2/WPA-PSK The parameters’ description of Mixed WPA2/WPA-PSK mode, please refer to the WPA-PSK mode. 5.3.3 MAC Filter Choose Wireless > MAC Filter to display the following page.
User Manual This page is used to allow or reject the wireless clients to access the wireless network of the wireless router. In this page, you can add or remove the MAC filters. The MAC restrict modes include Disabled, Allow, and Deny. Disabled: Disable the wireless MAC address filtering function. Allow: Allow the wireless clients with the MAC addresses in the MAC Address list to access the wireless network of the wireless router.
User Manual This page allows you to configure the wireless bridge features of the wireless LAN interface. AP mode: you may select Access Point or Wireless Bridge. Bridge Restrict: Enable or disable the bridge restrict function. Remote Bridges MAC Address: Enter the remote bridge MAC address. After finishing setting, click the Apply/Save button to save and apply the settings. 5.3.5 Advanced Settings Choose Wireless > Advanced to display the following page.
User Manual Band: You can select 2.4GHz or 5GHz. Channel: Fill in the appropriate channel to correspond with your network settings. All devices in your wireless network must use the same channel in order to work correctly. This router supports auto channeling functionality. Auto Channel Timer(min): Specifies the timer of auto channelling. 802.11n/EWC: Select disable 802.11n or Auto. Bandwidth: Select the bandwidth for the network. You can select 20MHz in Both Bands, 20MHz in 2.
User Manual Fragmentation Threshold: Packets that are larger than this threshold are fragmented into multiple packets. Try to increase the fragmentation threshold if you encounter high packet error rates. Do not set the threshold too low, since this can result in reduced networking performance. RTS Threshold: This value should remain at its default setting of 2347.Should you encounter inconsistent data flow, only minor reductions are recommended.
User Manual Note: The advanced wireless setting is only for the advanced user. For the common user, do not change any settings in this page. 5.3.6 Station Info Choose Wireless > Station Info to display the following page. This page shows the authenticated wireless stations and their status. 5.4 Voice Choose Voice and the submenus of Voice are shown as below. 5.4.1 VoIP Status Choose Voice > VoIP Status and the Voice Status page appears.
User Manual 5.4.2 SIP Basic Setting Choose Voice > SIP Basic Setting, and the following page appears.
User Manual Figure 7 SIP Basic Setting – 1 113
User Manual Figure 8 SIP Basic Setting - 2 Bound Interface Name: you can select the bound interface name from the drop-down list. SIP Local Port: Set the SIP local port of the gateway, the default value is 5060. SIP local port is the SIP UA (user agent) port. SIP domain name: Enter the SIP domain name that you want to set.
User Manual Use SIP Proxy: Select the checkbox of Use SIP Proxy, if your DSL router uses a SIP proxy. SIP proxy allows other parties to call DSL router through it. When it is selected, the following fields appear. – SIP Proxy: The IP address of the proxy. – SIP Proxy port: The port that this proxy is listening on. By default, the port value is 5060. Use SIP Outbound Proxy: Some network service providers require the use of an outbound proxy.
User Manual Authentication name: Set the user name of authentication. Password: Set the password of authentication. Cid Name: User name. It is the Display Name. Cid Number: Set the caller number. It must be a number of 0~9. ptime: You can use it to set the packetization time (PT). The PT is the length of the digital voice segment that each packet holds. The default is 20 millisecond packets. If selecting 10 millisecond, packets improve the voice quality.
User Manual Figure 9 SIP Advanced Setting - 1 117
User Manual Figure 10 SIP Advanced Setting - 2 Line: It displays the line you want to configure. Call waiting: If call waiting is enabled on a line, you can hear the call waiting tone during a call, press FLASH on the phone to answer the second call. The first call is automatically placed on hold. To switch between calls, press FLASH again. Select Call waiting to enable this feature.
User Manual Call forward feature settings (Busy or All) take priority over the call waiting feature. Call waiting feature is ignored on new incoming calls if there is already a call on hold or in conference. Unconditionally Call forwarding number: Enter the number that you want to set. It is the feature that forwards all incoming calls to an appointed number unconditionally. Busy Call forwarding number: Enter the number that you want to set.
User Manual Bypass Codec: You can select it from the drop-down list. Enable T38 redundancy support: Select the check box to enable this function. Enable vbd redundancy support: Select the check box to enable this function. RFC2198 Payload Value (range 96~127): Enter the RFC2198 payload value that the valid range is 96 ~ 127. Registration Expire Timeout*: Enter the registration expire timeout. Session Expire Time: The interval of dialog refreshing time.
User Manual SIP Transport Protocol: Select the transport protocol to use for SIP signaling. Note that the SIP proxy and registrar need to support the protocol you select. Enable Local Supplementary Service: Select the checkbox to enable the supplementary service settings by the telephone set. If you deselect the checkbox, the supplementary service can not be set by the telephone set. After setting, click Apply to take the settings in to effect. 5.4.
User Manual Vodsl Console Log Level: Select it from the drop-down list. SIP Log Server Settings: Set SIP log server IP address and port, then the log message of the VoIP is sent to the device which IP address you set to. If you want use this function, both of the IP address and port must be set correctly. Gain Settings: Gain is a measure of the ability of a circuit (often an amplifier) to increase the power or amplitude of a signal. You can increase or decrease ingress gain and egress gain.
User Manual to the next hop. In fact, many implementations integrate these two into one server, so in many case registrar and proxy refer to the same IP. Step 1 Select the right interface to use for registering, depending on where Step 2 Select the checkbox of Use SIP Registrar, and fill in the IP address and Step 3 Fill the extension information: Authentication name, Password, Cid proxy/registrar resides. If use WAN link, ensure that it is already up. port with the right value. Name and Cid Number.
User Manual 5.4.6.5 Call Return For incoming calls, the DSL router remembers the number of calling party. (1) Enable Call Return in the Voice--SIP Advanced Setting web page. (2) Press *69 to return a call. (3) Now you can make the call as if you have dialed the whole number. 5.4.6.6 Call Hold Call hold enable you to put a call to a pending state, and pick it up in future.
User Manual (2) Press FLASH to hold the first party. (3) Dial #91 + third party number. (4) After the third party answering the call, hook on your phone. (5) Now the first party takes over the call and he is in connection with the third party. 5.4.6.10 Call Forwarding No Answer If this feature enabled, incoming calls are forwarded to third party when you does answer them. It involves in two steps: setting the forwarding number and enable the feature.
User Manual (5) Now all three parties are in a three-way conference. 5.4.6.14 T38 Faxing To make T38 faxing, enable T38 support on the Web. After that, connect a fax machine to a FXS port of the DSL router. Now you can use it as a normal phone, and it is able to send or receive fax to or from other fax machines on the VoIP network. In the initial setup, faxing behaves like a normal call. After the DSL router detects the fax tone, it switch to T38 mode, and use it as the transmit approach. 5.4.6.
User Manual 5.5.2 Fault Management Note: The Fault Management is only available for VDSL PTM Click Diagnostics > Fault Management, and the following page appears.
User Manual 5.
User Manual 5.6.1 Settings Backup Choose Management > Settings > Backup to display the following page. In this page, click the Backup Settings button to save your router’s settings to your local PC. Update Choose Management > Settings > Update, and the following page appears. In this page, click the Browse… button to select the correct new settings file, and then click the Update Settings button to update the router’s settings.
User Manual 5.6.2 System Log Choose Management > System Log to display the following page. In this page, you are allowed to configure the system log and view the security log. Configuring the System Log Click the Configure System Log button to display the following page. In this page, you can set 3 types of system log modes, including Local, Remote, and Both. Local: When selecting Local, the events are recorded in the local memory.
User Manual Click the View System Log button to display the following page. In this page, you can view the system log. Click the Refresh button to refresh the system log. Click the Close button to exit. 5.6.3 SNMP Agent Choose Management > SNMP Agent, and the following page appears. Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in this device.
User Manual In this page, you may enable or disable the SNMP agent and set the parameters such as the read community, system name and trap manager IP. After finishing setting, click the Save/Apply button to save and apply the settings. 5.6.4 TR-69 Client Choose Management > TR-069Client to display the following page. WAN Management Protocol (TR-069) allows an Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection, and diagnostics to this device.
User Manual In this page, you may configure the router to synchronize its time with the Internet time servers. After enabling Automatically synchronize with Internet time servers, the following page appears.
User Manual In this page, set the proper time servers, and then click the Apply/Save button to save and apply the settings. 5.6.6 Access Control Passwords Choose Management > Access Control > Passwords, and the following page appears. In the page, you can modify the username and password of different users. After finishing setting, click the Apply/Save button to save and apply the settings. Services Choose Management > Access Control > Services Control and the following page appears.
User Manual In this page, you can enable or disable the different types of services. After finishing setting, click the Apply/Save button to save and apply the settings. 5.6.7 Update Software Choose Management > Update Software, and the following page appears.
User Manual If you want to upload the software, click the Browse… button to choose the new software, and then click the Update Software button. Note: When software update is in progress, do not shut down the router. After software update completes, the router automatically reboots. Please make sure that the new software for updating is correct, and do not use other software to update the router. 5.6.8 Reboot Choose Management > Reboot and the following page appears.
User Manual The connection between the ADSL router and your computer, hub, or switch. The running status of your PC, hub, or switch. (3) Q: Why the DSL indicator is off? A: Check the connection between the “DSL” port of router and the wall jack. (4) Q: Why Internet access fails while the DSL indicator is on? A: Check whether the VPI, VCI, user name, and password are correctly entered.
User Manual A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
User Manual corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this [US:VW7DL02BSR630N] does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. his product meets the applicable Industry Canada technical specifications.
User Manual FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
User Manual IC This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
User Manual having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (Model: SR630n) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne.
