www.newsmartsafe.com iSmartEV P03 User Manual Copyright Information Copyright © 2021 by SHENZHEN SMARTSAFE TECH CO.,LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of SMARTSAFE.
iSmartEV P03 User Manual www.newsmartsafe.com claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of SMARTSAFE or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name.
www.newsmartsafe.com iSmartEV P03 User Manual during the maintenance process. Notice: When the high voltage distribution box needs to be repaired or replaced, remove the positive and negative high voltage connectors connected to the battery pack carefully, and wrap the exposed wires with electrical tape to avoid electric shock. 4.
iSmartEV P03 User Manual www.newsmartsafe.com of good low voltage debugging, so as to determine whether the battery has leakage. If there is leakage, it should be checked in time, and high voltage debugging cannot be carried out. 7. During disassembling and installing the power battery pack assembly; wrap the high-voltage wiring harness connector connected to the high-voltage distribution box with insulation tape.
www.newsmartsafe.com iSmartEV P03 User Manual incorrect data, please ensure that the vehicle battery is fully charged and that the connection of the vehicle diagnostic seat is clean and safe. 7. The vehicle battery liquid contains sulfuric acid, sulfuric acid is corrosive to the skin, so you should avoid direct contact between the battery liquid and the skin during the operation, especially do not splash it into the eyes, and do not put it close to the fire. 8.
iSmartEV P03 User Manual www.newsmartsafe.com WARNING It indicates an imminent hazard that, if unavoidable, will result in death or serious injury to the operator or bystander. Example: Warning: Reading a fault code during troubleshooting a vehicle is only a small step in the diagnostic process. The vehicle fault code is only used as a reference, and parts cannot be replaced directly on the basis of the given fault code definition.
www.newsmartsafe.com iSmartEV P03 User Manual Contents 1. Packing List ...............................................................................1 2. Product Introduction ................................................................6 2.1 Overview .................................................................................6 2.2 iSmartEV P03 ......................................................................... 6 2.3 iSmartEV BOX ..............................................................
iSmartEV P03 User Manual www.newsmartsafe.com 8.1 Technical Parameters .......................................................... 63 8.2 How to Operate .................................................................... 63 8.3 Detection Examples ............................................................. 70 8.4 Precautions ...........................................................................72 9. Insulation Test ........................................................................ 73 9.
www.newsmartsafe.com iSmartEV P03 User Manual 11.13 Coolant Bleed ...................................................................92 11.14 Engine Power Balance Monitoring .................................. 92 11.15 IMMO Prog ....................................................................... 92 11.16 IMMO Service ...................................................................92 11.17 High Voltage Battery Diagnosis ....................................... 92 11.
iSmartEV P03 User Manual www.newsmartsafe.com 13. Remote Diagnose ............................................................... 101 13.1 Messages ......................................................................... 101 13.2 Contacts ........................................................................... 101 13.3 Remote ............................................................................. 102 14. IMMO Matching ................................................................... 104 14.
www.newsmartsafe.
www.newsmartsafe.com iSmartEV P03 User Manual 1. Packing List Main Unit and Accessories No.
iSmartEV P03 User Manual 6 OBD I Transfer Cable 1 7 Cigarette Lighter 1 8 2 www.newsmartsafe.
www.newsmartsafe.com iSmartEV P03 User Manual Battery Jumper Adapters No.
iSmartEV P03 User Manual www.newsmartsafe.com Other Accessories 4 No.
www.newsmartsafe.
iSmartEV P03 User Manual www.newsmartsafe.com 2. Product Introduction 2.1 Overview iSmartEV P03 is a professional integrated detection tool for new energy vehicles developed by SMARTSAFE. It supports the detection of new energy vehicles and vehicle battery packs. It integrates professional measuring tools for new energy vehicles such as oscilloscope, multimeter, insulation test and current clamp. 2.2 iSmartEV P03 1. Touch Screen 2. Microphone 3. Handle 4. Volume5. Volume+ 6.
www.newsmartsafe.com iSmartEV P03 User Manual 9. Insulation 10. Current Clamp 12. Multimeter Function Button Area 11. Oscilloscope Function Button Area 13. Insulation Test Function Button Area 14. Rear Camera module: 15. Flashlight 21. Insulation Test Calibration Port 16. USB Type-C 17. USB Type-A - Used to connect the power adapter for charging or connect the computer for data transmission. 18. DC 12V Power Jack 19. Loudspeaker 20. Holder 21~24 are related interfaces of insulation function 22.
iSmartEV P03 User Manual www.newsmartsafe.com current. 24. EARTH/Ground Terminal (Less Than 400ma) Current Input Terminal - Connected to the shell or ground of the detected equipment. 29. Negative Common Terminal 25~30 are related interfaces module: 30. Voltage/Resistance And Other Input Terminals 31~32 are related interfaces 25. Fuse (500mA/600V) of oscilloscope function of multimeter function module: 26. Fuse (12A/600V) 31. Oscilloscope Channel 2 27. 10A Current Input Terminal 32.
www.newsmartsafe.com iSmartEV P03 User Manual 2 DC 12V Power Supply Jack 3 Wi-Fi Indicator 4 USB Indicator 5 Bluetooth Indicator 6 Vehicle Communication Indicator 7 Power Supply Indicator 8 OBD-II Port 2.4 Technical Parameters 2.4.1 iSmartEV P03 Item Operating System CPU Specification Parameters Android 10.0 8-core Processor, 2.0GHz Memory 8GB Storage 256GB Display Screen Camera Wi-Fi Communication Battery 10.1-inch Touch Screen, 1920*1200 Resolution 13 Million Rear Camera 2.
iSmartEV P03 User Manual www.newsmartsafe.com 2.4.
www.newsmartsafe.com iSmartEV P03 User Manual 3. Initial Use 3.1 Charge the Tablet Warning: Please use the charger that comes with the product for charging. We are not responsible for any damage or economic loss caused by charging with a charger other than the one designated by us. Please follow the following steps to charge the iSmartEV P03 tablet: 1. Insert one end of the switching power supply into the DC power jack of the host, and connect the other end to the power socket. 2.
iSmartEV P03 User Manual www.newsmartsafe.com 3.2.1 Turn On Press and hold the power button on the device until the screen lights up. 3.2.2 Turn Off Press and hold the power button on the device until the shutdown prompt dialog box pops up on the screen, tap Power off to shut down the device or tap Restart to restart the device. 3.3 Network Connection When using the device for the first time, you need to register a personal account, activate the VCI connector, and upgrade the diagnostic software or APK.
www.newsmartsafe.com iSmartEV P03 User Manual On the main interface, click Other -> Personal Center -> Login, and the following dialog box will pop up: (If you are a new user, follow Section A.) (If you are registered, please refer to Section B for login.) (If you forget your password, please refer to Section C to reset it.) A. If you are a new user, please tap New Registration to enter the registration page.
iSmartEV P03 User Manual www.newsmartsafe.com Enter the product serial number and activation code. The product serial number and activation code can be obtained from the password envelope in the package box. Note: If you skip the activation step here, you can also go to Other -> Personal Center -> Activate VCI to activate after entering. Tap Activate to complete the registration.
www.newsmartsafe.com iSmartEV P03 User Manual Tap OK to enter the software update interface. On the software update page, tap Update to start downloading. After the download is complete, the system will automatically install the software. Note: During the update, ensure that the network connection is normal. In addition, due to the large number of software, it may take a long time (depending on the network speed). Please wait patiently. B.
iSmartEV P03 User Manual www.newsmartsafe.com password and tap Login to enter the account. Prompt: The device has the user information memory function. If multiple accounts have logged in to the device, click the triangle drop-down button behind the user name input box to select the corresponding account to log in. C. If you forget the password, please tap Retrieve Password and then set the new password according to the prompts on the screen.
www.newsmartsafe.com iSmartEV P03 User Manual 4. Getting Started 4.1 Main Interface and Bottom Navigation Bar 4.1.1 Main Interface The main interface of iSmartEV P03 host mainly includes the following functional modules: Items Description Battery Diagnose Used to perform in-depth system detection on vehicle battery packs. Diagnose Used to detect the electronic control system of the whole vehicle. Oscilloscope Used to measure the voltage signal and analyze the form of the electronic signal.
iSmartEV P03 User Manual Test Current Clamp www.newsmartsafe.com electrical equipment. Used to perform AC/DC current test and DC voltage test. Special Function Used to perform common special functions such as vehicle maintenance, service and adjustment. ADAS Calibration This function module needs to work with the specified ADAS calibration tool (purchased separately, for example, ADAS mobile) to calibrate the ADAS (Advanced Driver Assistance System).
www.newsmartsafe.com iSmartEV P03 User Manual 4.1.2 Bottom Navigation Bar The bottom navigation bar contains the following buttons: Icon Name and Function Description Browser-click this button the start the browser. Screenshot-click this button to capture and save the current screen image. The screenshot is saved in the Screenshots folder. VCI connection indicator-after the host is successfully connected to the VCI connector, this button lights up in green.
iSmartEV P03 User Manual www.newsmartsafe.com or around the driver’s side for most vehicles. For some vehicles with special designs, the DLC location may vary. If the DLC cannot be found, refer to the vehicle’s service manual for the location. 4.2.2 Vehicle Connection Connect one end of the included OBD extension cable to the OBD-II port of iSmartEV BOX, and the other end to the vehicle’s DLC port. 4.
www.newsmartsafe.com iSmartEV P03 User Manual indicator of the VCI connector is also on. 4.3.2 USB Communication When the tablet and VCI connectors are connected through USB cables, the system automatically switches to USB communication mode. At this time the VCI connector icon at the bottom of the screen will light up, and the USB indicator of the VCI connector will also light up.
iSmartEV P03 User Manual www.newsmartsafe.com 5. Battery Diagnose This function is used to check the detailed data and fault information of battery pack, helping users to quickly determine the abnormal status and fault point of battery pack. Danger: The personnel who operate the battery pack test must wear protective equipment such as insulation gloves, insulation shoes and goggles. Operating the battery pack without protection can cause a serious electric shock. 1.
www.newsmartsafe.com iSmartEV P03 User Manual Select the vehicle model and year. 3. Select the connection method of battery pack.
iSmartEV P03 User Manual www.newsmartsafe.com A. OBD Connector Diagnosis The battery pack of the vehicle was tested by connecting the iSmartEV BOX to the vehicle OBD interface through an OBD extension cable. B. Non-standard Connector Diagnosis Connect the iSmartEV BOX and the low-voltage signal communication interface of the battery pack respectively with the battery pack special connector (optional) to test the vehicle battery pack.
www.newsmartsafe.com iSmartEV P03 User Manual C. Jumper Diagnosis According to the wiring diagram prompted by the software, the jump-8 jumper is used to connect the iSmartEV BOX and the lowvoltage signal communication interface of the battery pack respectively to detect the battery pack of the vehicle. Note: The picture here is an example only. The connection mode varies with vehicle types. Please connect based on the wiring diagram prompted by the software. 4.
iSmartEV P03 User Manual www.newsmartsafe.com Description for Screen Buttons: Main Interface Exit Report Reference Value Click to return to the main interface. Click to exit the current detection process. Click to view/save the detection report of battery pack. Click to select the voltage reference range of different types of batteries.
www.newsmartsafe.com iSmartEV P03 User Manual of modules and other parts in the battery pack, and mark the maximum/minimum temperature cell in the battery pack.
iSmartEV P03 User Manual www.newsmartsafe.com 6. Diagnose This function is mainly used for vehicle diagnose. Users can use AutoDetect to quickly identify vehicle information and enter the system for vehicle diagnose, or manually select models and systems for detection. 6.1 AutoDetect Use AutoDectect to quickly identify vehicle information and vehicle diagnose, without manual selection of vehicle type.
www.newsmartsafe.com iSmartEV P03 User Manual 6.2 Manual Selection 1. Tap Diagnose on the main interface to enter the vehicle brand selection interface. 2. Click the vehicle brand to be tested to enter the model version information interface. Here we take Demo (Version 15.43) as an example to demonstrate how to diagnose a vehicle.
iSmartEV P03 User Manual www.newsmartsafe.com Screen Button Description: Vehicle Coverage What’s new Introduction Note OK Click to view the current vehicle models that can be tested. Click to view the updated points of the current diagnostic software. Click to view the specific use of the current diagnostic software. Click to view precautions when using the current diagnostic software. Click to go to the next step. 3. Tap Demo to go to the next step.
www.newsmartsafe.com iSmartEV P03 User Manual 4. Select vehicle brand and model. Here we take VW as an example. 5. Select the scan option that need to perform. The system supports two display modes: topological diagram and list. User can also tap ADAS Calibration to perform ADAS related test options of vehicles . Note: The specific system and special functions provided depend on the vehicle type.