Wireless APP Camera Installation and Operating Instructions C935IP Version 1.0 PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT AND KEEP THIS MANUAL FOR FUTURE REFERENCE.
The state of art WAPP camera is capable of deliver high quality Digital High Definition (HD) video to your smart-mobile device(s), which would require higher internet bandwidth. Due to your local internet environment condition, your mobile device(s) may display black-screen or temporary disconnect to the WAPP camera. Make sure the WAPP camera is operating with sufficient internet bandwidth, 1Mbps (upload/download speed) is suggested.
CONTENTS INTRODUCTION ............................................................................................................. 2 WIRELESS DEVICES OPERATING RANGE .................................................................. 2 IMPORTANT SAFETY PRECAUTIONS ....................................................................... 2 KIT CONTENT .............................................................................................................................. 4 SAFETY AND INSTALLATION TIPS....
INTRODUCTION PLEASE READ BEFORE YOU START Always use discretion when installing CCTV equipment, especially when there is perceived policy. Enquire relevant local regulations applicable to the lawful installation of video recording/surveillance. Third party consent may be required. WIRELESS DEVICES OPERATING RANGE Ensure the signal reception viewed from the wireless camera(s) is the best possible reception between the camera(s) and the Wi-Fi router.
FCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Products with CE Marking comply with EMC Directive (2004/108/EC); Low Voltage Directive (73/23/EEC); R&TTE(1999/5/EC); ROHS Directive (2011/65/EU) issued by the Commission of the European Community.
KIT CONTENT A Wireless App Camera x 1 B Camera Stand x 1 C Camera Antenna x 1 D Power Adapter x 1 E Screw Pack x 1 F Rj45 Connect Jack x 1 G Manual CD x 1 F Quick Start Guide x 1 Tools Required: Electric drill 5mm masonry drill bit 15mm masonry drill bit No. 2 Philips screwdriver For best system performance: - iOS: iPhone4S / iPad2 / Mini iPad or above. Maximum 12 registered camera connections. - Android: 1.5G dual core processor or above / 960*540 pixel or above.
SAFETY AND INSTALLATION TIPS Do not attempt to open the units with the power adaptor plug connected to avoid any risk of personal injury. When installing CCTV camera(s), always follow manufacturer's advice when using power tools, steps, ladders, etc. and wear suitable protective equipment (e.g. safety goggles) when drilling holes. Before drilling holes through walls, check for hidden electricity cables and water pipes. The use of cable/pipe detector is advisable.
NIGHT VISION The camera has built-in infrared LEDs to allow you to view at night for 24-hour surveillance. The LEDs will automatically activate at night and the picture viewed will turn to black and white. The night viewing range is up to 5 meters. CAMERA INSTALLATION Secure camera stand on the stable surface. Loosen up the Thumb screw. Adjust proper view angle then secure the joint with T-bolt.
CAMERA OVERVIEW Antenna Power Indicator Signal Indicator SD Card Slot PIR Infrared LEDs Stand RJ-45 Cable Power Cable 7
DOWNLOAD AND SETUP THE APP The Wireless APP camera is designed to deliver live video footage directly to your smart phone or tablet device. Please follow these steps to download, setup and use the APP. APP Name: OMGuard HD Download the App 1. From you smart phone or tablet device, click the APP Store/Google Play and search for “OMGuard HD”. 2. Once located the APP, select download. 3. Once download completed, you will find the APP icon on your mobile device screen.
1. Make sure the mobile device you are using is connected to the same Wi-Fi router the camera is connected to. 2. Locate the “OMGuard HD” icon in your mobile device and launch the App. 3. Tap the ADD CAMERA icon to add a new camera. Then click the SEARCH button for a quick setup. The APP will search available camera(s) connecting to the Wi-Fi router and display the camera information in the pop up list.
In most cases, you can successfully add the camera according to the steps above. However, the camera will not find the network if Wi-Fi router turns off the SSID broadcasting function. Please enable the SSID broadcasting to complete the settings. Note: Most Wi-Fi routers broadcast the Service Set Identifier (SSID) by default. This is the name of your wireless network, and SSID broadcasting is how Wi-Fi-enabled devices find networks.
LIVE VIEW / SNAPSHOT / RECORDING Tap to take snapshot image(s) of the video. The captured snapshots will be stored in your mobile device. Tap to turn ON/OFF the volume. Tap to Start/Stop recording. The recorded video file will be stored in the memory card of your camera. Tap to return to the main page. The APP allows users to have access to live video. User can take snapshot image(s) and record the live video.
VIEWING YOUR SNAPSHOTS For iOS You snapshots will be named with the time stamp and saved into the Camera Roll location of your mobile device. For Android You snapshots will be named with the time stamp and saved into the Photo Gallery > snapshot folder on your mobile device. PLAYBACK YOUR VIDEOS The recorded video file(s) on your camera is automatically saved to the memory card inserted in your camera. You can remotely access the file(s) for playback via your mobile device.
Tap EVENT LIST icon and the Date-Time filter would appear. User may define the period for system to display all available recorded file(s) for playback. During the playback, you can tap the PAUSE icon to pause / resume the video, MUTE to deactivate/activate the audio function and GO BACK icon to return to the event list section. You may also review recorded video file(s) with your PC. For best performance, please use “Free Video Converter” from http://www.freemake.
To Download/Delete the video file(s) in the EVENT LIST section, please follow the steps below: ．DOWNLOAD Long press the video clip to download the file onto your movbile device. Note: During the download process, system will stop both the live view and recording functions. APP will automatically inform any user accessing the camera that the systemis busy and the connection has been terminated.
This function helps user to easily withdraw the recorded file(s) from the memory card. It is strongly suggested to download the file(s) at your home Wi-Fi network (WLAN), meaning the mobile device(s) is connecting to the same Wi-Fi router as the camera. Minimum bandwidth requirment is 1Mbps (upload/download). Download process may be force stopped if the bandwidth becomes too slow and cannot continue. Note: For Android system, please use "MX Player" APP for playback downloaded video file(s).
MAIN PAGE OVERVIEW The MAIN PAGE section offers user an overview for all registered camera(s), including camera status (connected/disconnected). User can quickly access the camera(s) in the list. When multiple cameras are registered, scroll down to locate the registered camera for access. (iOS) (Android) ADD CAMERA The ADD CAMERA icon allows you to register additional camera(s) to the system. The system supports up to 3 concurrent user connections. 1.
4. Enter the default password 123456 in the Security Code column. 5. Click SAVE to complete the camera settings. The APP attempts to establish camera connection. Once the camera is successfully connected, the “Connected” status will be shown on the left upper corner. 6. Repeat step 2 to 5 to add more cameras.
In the CAMERA SETTING section you will allow to (1) configure system setting, (2) unregister camera from the APP and (3) enter event list for recorded video file(s) playback. Tap the CAMERA SETTING icon to enter/exit CAMERA SETTING. Tap the CAMERA SETTING icon. The following icons appear on the panel. (iOS) (Android) Tap the ADVANCED SETTING icon to setup camera configuration. (Please refer to "Advanced Setting" for detail). Tap the DELETE icon to remove the camera connection.
SETUP PIN LOCK (iOS) (Android) If you enable PIN Lock, the user will be asked to enter the PIN code when you launch the APP. 1. 2. Enable the “Enable lock when starting” function. Then enter your PIN code. Confirm your PIN code again. Note: If you forgot your PIN code, please uninstall the APP and reinstall it on the mobile device. NOTIFY (PUSH NOTIFICATION) The WAPP camera supports motion detection function.
1. 2. 3. 4. Launch Settings from your Home screen. Tap Notifications. Scroll down to find “OMGuard HD” APP and tap on it. Switch the toggle to ON/OFF in Notification Center. Note: It takes time for the changes to take effect in iOS, normally within 2 hours. For Android If you want to enable/disable it, please follow the steps below. Note: The internet connection and wireless network interference may influence the performance of push notification service.
ADVANCED SETTING This chapter explains the advanced settings for administrator. Administrator is the one who owns the administration password and has the full control to the WAPP camera. The administrator can access all WAPP functions and settings, while general users can receive the surveillance images for live view/screen capture/video recording and may not manage the camera settings.
ADMIN PASSWORD The Admin Password is a specific security code for administrator to change the advanced settings. The default admin password is 123456. Please use this function to change the default admin password into your personal admin password. For the protection of your system configuration, every time you change the advanced settings, you need to enter the admin password. Please change the admin password periodically.
TIME ZONE The drop-down list shows the world time zone. Select the time zone that will work the best for you. If your date/time is during the daylight saving time period, please check the Daylight Saving box to adjust the system time properly. DAYLIGHT SAVING Activate/Deactivate the daylight saving function. DEVICE SECURITY CODE The Device Security Code is a specific security code to access the camera. The default password of the camera is 123456.
Envi r onment Mode The Environment Mode settings allows you to select the power line frequency used at the location of WAPP camera. The power line frequency varies depending on geographic region. It may cause image flicker if wrong frequency is selected. Please check with local authorities for proper setting. Low Light Enhancement The Low Light Enhancement Mode is for improving the night view video image by providing 5 levels to select from (5 = brightest).
SENSITIVITY SETTING This defines the camera parameter for motion detection. Detection Mode PIR is hardware-based biomass detection. SOFTWARE uses advance software analysis to enhance PIR accuracy. Motion Detection (available for Software Mode ONLY) HIGH – Suitable for detecting smaller object(s) within 5 to 6 meters LOW – Suitable for detecting larger object(s) within 3 to 5 meters Note: The HIGH/LOW setting for Motion Detection only takes effect when user chooses “PIR & SOFTWARE” in Detect Mode.
Email to XXX@gmail.com Enter the email address for the recipient who receives the email alert. SD CARD SETTING Formatting your memory card will ERASE all the data from it and you will not be able to get the data back. Please back up your video files BEFORE formatting the memory card. Note: The system is optimized to Class 10 memory card. Memory card with lower specification will decrease the recording and playback function efficiency.
TROUBLE SHOOTING IF… The APP cannot found the camera Wi-Fi router is not shown in the drop down list SOLUTION • Make sure your network supports the DHCP protocol. • Make sure the camera and your mobile device connect to the same Wi-Fi router for the first setting. • Make sure the Wi-Fi router is activated. • Make sure the camera is properly powered on. • Use the “ADD CAMERA” function to manually add the camera. • Make sure SSID broadcasting function is enabled in the Wi-Fi router.
Low wireless signal Poor image quality • Wireless devices such as wireless home stereo system may reduce the signal strength. Leave as much space as possible between the camera/mobile device and these wireless devices. • Clean the camera lens using lens cleaning cloth. Spots or dust on the lens can also cause image quality problems. • Make sure the sensitivity setting is turned ON Motion detection is (please refer to the Sensitivity Setting section).
Bright white spots appear at night time • The camera's infrared LEDs produce invisible light that reflects off surfaces such as glass. Install the camera on the other side of windows or place the lens flush against the surface to improve the night vision. It is suggested to install camera(s) under well-lit area. Note: Please check the environment rating (Ingress) of the camera(s) before installing outdoors. Memory card error • Make sure the memory card is correctly inserted and formatted.
PRODUCTION SPECIFICATION Networking Parameter Wireless Technology IEEE 802.
STORAGE MEDIA MANAGEMENT Micro SD Card Capacity HD / Better Image Better Streaming 4G 150 events 180 events 8G 300 events 360 events 16G 600 events 720 events 32G 1,200 events 1,440 events (Class 10) 31
