HA700+ Wireless alarm system with built-in phone transmitter Complete battery operated Installation & operation manual 1
TABLE OF CONTENTS INTRODUCTION AND GENERAL POINTS .............................................................................. 3 PRE-PROGRAMMING .............................................................................................................. 3 1. PACKAGE CONTENT ......................................................................................................... 5 2. INSTALLATION PLANNING ............................................................................................... 6 3.
INTRODUCTION AND GENERAL POINTS CONGRATULATIONS, you have just made a great step to protect yourself, your home and its content and against assault and theft. Of course an alarm system does not constitute an absolute guarantee against these wrongdoings, but it is sufficiently deterrent. PRE-PROGRAMMING The accessories of the HA700+ were preprogrammed in the factory to a standard configuration that reduces the installation time to the bare minimum.
INTRODUCTION We strongly recommend to read this guide carefully before to start any installation, and to follow the installation instructions in order, with the items on a table (if you add or modify accessories). The alarm system HA700+ was designed according to the following principles: Easy installation: Anyone can install the system. It does not require any special knowledge in the alarm field. No need of special tools.
1. PACKAGE CONTENT HA700+ The initial alarm kit should contain the following items: • 1 x Station HA700C • 1 x Wireless movement detector (PIR) SA68P • 1 x Wireless door/window (magnetic) detector SA68M • 1 x Remote control HA700R Also included: • Installation & operation manual • Securing kit • 4x 1.5V (LR20) batteries (HA700) • 1x 3.6V Lithium battery (SA68P) • 1x 3.
2. INSTALLATION PLANNING Due to a total absence of cable works, a wireless alarm system is very easy to install. It can be changed easily, because it is simple to transfer a detector to a more efficient place if needed. This way, you do not have to worry about realizing a perfect installation from the start. Before to proceed to any installation, it is essential to asses carefully the intrusion risks for your home plan, and specifically its openings to the outside.
IMPORTANT NOTE BEFORE INSTALLING This section gathers significant information about the system operation or its accessories. ADVICE BEFORE INSTALLING 1. The kit accessories are already programmed in the station BUT extra accessories must be learned by the station so they can dialogue with it. 2. The accessories have an initialization delay, it is therefore imperative that to insert the batteries in each accessory 5 to 10 minutes before to start programming or tests. 3.
3. INSTALLING AND PROGRAMMING THE STATION 3.1 Installing and programming the alarm station 3.1.1 System description A. Panic LED B. Area 2 LED C. Area 1 LED D. STATUS LED E. Low battery LED F. Microphone G. Keyboard H. Speaker (100dB) I. Fixing slots J. Self-protection K. Telephone socket L. Mains adapter (not included) M. Cable tray N. Metal mounting bracket O. Fixing screw P.
3.1.2 Installing the system LOCATION OF THE STATION The following aspects are to be considered when selecting a mounting location for the station: Check that an intruder willing to reach the station is forced to use an exit protected by a magnetic detector or must walk in front of an infrared detector. The station must be mounted near a telephone socket or the BOX. The station must be placed out of sight of potential intruders and in a safe location, which can be easily accessed for maintaining the system.
4. Insert the 4 LR20 alkaline batteries. and fix it there to the metal bracket using the screw. 5. Close the compartment at the rear panel of HA700. 6. Connect the telephone cable 7. Mount the alarm station at this place. Your alarm system is now ready CHANGING THE STATION BATTERIES When the station batteries need to be changed, the station will emit a beep every 30 seconds and the yellow LED will flash. To change the batteries: Switch the station to test mode (see page 18).
Programming the station 3.1.3 Programming the personal code A personal code must be saved first by using the alarm station keys. You must choose this code, it will be used to enable or disable the system. To change the code: Enter the factory code 1234. Then push the key 6, a long beep will be emitted and the STATUS LED will flash. Enter your 4 digit personal code. Push the key 6 to confirm the code change, a long beep will be emitted to confirm that the code has changed.
3.1.6 Alarm delay It is about the working time of the built-in siren when an alarm is triggered. The delay can be set on 1, 2 or 3 minutes. To change the alarm delay: Enter the factory code 1234 (or your personal code). Then push the keys 0 and then 4, a long beep will be emitted and the STATUS LED will flash. Choose the alarm delay. Push the key 1 for 1 minute OR the key 2 for 2 minutes OR the key 3 for 3 minutes, one confirmation beep will be emitted. NOTE: The alarm delay is 1 minute by default. 3.1.
3.2 Installing and programming accessories 3.2.1 Detector learning TABLE: DETECTOR OPERATION DEPENDING ON THE STATION ARMING MODES STATION ARMING MODE PARAMETERS AREA 1* AREA 2* PANIC * TOTAL ARMING PARTIAL ARMING DISARMING DETECTOR ACTIVE DETECTOR INACTIVE DETECTOR ACTIVE DETECTOR INACTIVE DETECTOR ACTIVE * 10 detectors maximum per area To program a detector: Enter 1234 (or your personal code), followed by *, a long beep will be emitted and the STATUS LED will flash.
3.2.3 Remote control learning To program a remote control: Enter 1234 (or your personal code), followed by *, a long beep will be emitted and the STATUS LED will flash. Push the remote control disarming button. When the signal is received, a long beep will be emitted. Note: You can learn at most 4 remote controls. 3.2.4 Deleting remote controls The station cannot erase each remote control individually. If you want to erase a remote control, you must erase all remote controls.
3.3 Programming the phone transmitter 3.3.1 Programming the alert message During a call, the station delivers a message that you must record beforehand. The message maximum duration is 6 seconds. To record the message: Enter 1234 (or your personal code), followed by 5, the STATUS LED will flash. Stand 20-30 cm from the station and record your message. If your message lasts less than 6 seconds, push the key * to stop the recording.
4. ALARM STATION OPERATION 4.1 Arming the system During the system arming, whatever will be the chosen mode, there will be an exit delay of 15 seconds. The first 10 seconds will be silent, then there will be 1 beep every second, followed by a long beep at the end of the delay to confirm arming. The system has a total arming mode and a partial arming mode.
- Enter 1234 (or your personal code), followed by . 4.3 Chime mode You can set the station into chime mode. In this mode, it will emit a "ding-dong" when you pass in front of a movement detector or when you open a door/window equipped with a magnetic detector. CAUTION: In this mode the self-protections and the detectors saved in panic area will always be active and will trigger the station. To set the station into chime mode: - Enter 1234 (or your personal code), followed by 3. 4.
5. FUNCTION SUMMARY TABLE Procedure on the station Function 1234+01 Triggering mode #1 1234+02 Triggering mode #2 1234+03 Test mode Function description The station rings and the transmitter will call the programmed numbers. The station does not ring and the transmitter will call the programmed numbers. The station emits a "ding-dong" upon receipt of a detection or self-protection signal. Push 8 for 3 s. Enables/disables the exterior siren Push 9 for 3 s. Calls the first phone number.
6. ACCESSORY INSTALLATION AND OPERATION 6.1 Remote control HA700R The remote control allows you to activate several functions of your station (Disarming, Total Arming, Partial Arming, Panic and Test Mode). The remote control has a Panic switch, that when actuated causes immediately a complete alarm situation if the system is in Armed or Disarmed mode (except if the system is in Test mode). The remote control uses one CR2032 Lithium battery, which, in normal conditions, has a lifespan of more than 2 years.
CHOOSING A MOUNTING LOCATION The PIR Detector is suitable for mounting in dry interior locations only. The recommended position for a PIR Detector is in the corner of a room mounted at a height between 1.8 and 2m. At this height, the detector will have a maximum range of up to 10m with a field of view of 110°, subject to the position for the PCB being set in 5. The position of the PCB inside the PIR can be set to 5 different positions to adjust the range of the detector.
INSTALLING THE PIR DETECTORS (Ensure that the system is in Test Mode). 1. 2. Undo and remove the fixing screw from the bottom edge of the PIR. Carefully pull the bottom edge of the detector away from the rear cover and then slide down to release the top clips Carefully drill out the required mountingholes in the rear cover using 3mm drill according to whether the unit is being mounted in a corner or against a flat wall.
Note: On initial installation the detector should be set into Walk Test mode ready for testing. Upon completion of Walk Test mode, set DIP1 of SW2 to OFF for normal detection mode. 2. The PIR Detector incorporates an anti-false alarm feature designed to compensate for situations where the detector may be affected by environmental changes, (e.g. insects, air temperature, etc). This feature is called “sensitivity detection” and may be selected for high or low detection.
3. Mount the Detector to the fixed part of the frame along the opening edge opposite the hinges using either the double sided adhesive tape or screws provided. If fixing the Detector with screws; fit the Keyhole slot in the top of the Detector over the head of the smaller pan-head screw. Secure the bottom of the Detector using the 12mm countersunk head screw fitted within the battery compartment. You will need to drill out the centre of the fixing screw hole using a 3mm drill.
7. RESETTING THE STATION You can reset the station to delete all accessories, the message, the phone numbers and the personal code. To reset the station: - If possible, switch the station to test mode (see page 18). Dismount the station from its location and open the compartment at the rear panel of HA700. Remove the batteries. Move the jumper for reset. Position to reset the station Wait 5 minutes. Put the batteries back into place, the station beeps and the STATUS LED lights up for 3 seconds.
8. SPECIFICATIONS Common technical characteristics: Operating frequency : 868.35 MHz in ASK for detectors, remote controls and exterior keyboard. Operating temperature : -10°C~ +45°C Operating humidity : < 90% Operating range : 300m in open field for detectors, remote controls and exterior keyboard. Station HA700C 2 radio areas individually programmable, incorporating up to 10 detectors per area. 1 Panic Area (monitoring 24h/24h) for any detector, incorporating up to 10 detectors per area.
10. PRODUCT GUARANTEE This product has factory warranty according to EU regulations. Guarantee lasts for the number of years shown on the packaging, starting from the date of purchase. Keep the receipt - proof of purchase is required in order to rely on guarantee. In the case of problems, please contact with the store where you purchased the product. For further product information call to our Hotline or visit our website: www.smartwares.eu . You can also register your product there. 11.
