HA788GSM GSM Alarm User Manual 1. Product overview F. Speaker A. Touch keypad B. Microphone C. Siren G. Battery cover H. Wall mounting bracket D. RFID sensor area E. GSM status led When battery cover is removed: I. SIM card slot J. Battery connector K. DC-jack L.
. Features • • • • • • • • • • • • • 868MHz Radio Frequency 50 wireless zones SIM card slot for GSM connection SMS & phone call notifications up to 10 numbers Easy operation by App Easy disarm by RFID tag, with up to 50 tags supported. Dial and receive phone calls Hands-free two-way talking Siren Volume up to 95dB Notify user if door/window not closed when trying to Arm Hidden Duress Code capability Tamper protection feature RF jamming detection 3.
4. Definition of LEDs 5. Mounting the Alarm Panel LED Selecting a suitable location: Mount the alarm panel close to the door which you normally use to enter/exit your house. Note that the Alarm panel requires a power outlet to function properly. Ensure the location selected a good GSM signal. You can do this by cross checking the signal bar on your phone at that location. The panel must not be co-located or operated in conjunction with any other nearby transmitter or antenna.
6. Configure the Alarm panel There are 3 ways to configure the Alarm panel’; 1. Keypad: Basic and advanced settings can be configured through the touch keypad. Whenever a key is pressed, the LED will light up and a key tone will sound (when Key Tone is enabled). Refer to Appendix A for the full list of keypad and button combination to various settings. A 4-digit PIN code needs to be entered; the default PIN is ‘1234’. 2.
signal strength indicated as: - LED 1 :Good, LED 2: Normal, LED 3: Poor, - ALARM LED : No Signal / SIM card registration failure / No SIM card Siren enable/disable 6. Press 8 for 3 or more seconds during Test Mode would send a System On / Off command to the Wireless Siren. SMS test 7. Press 9 for 3 or more seconds during Test Mode would send a test SMS message (including the current Alarm Mode, Delay Time, Siren On/Off, and Alarm Time) to the Host Phone number.
8. When alarm occurs An alarm condition will be triggered when, in Fully Arm/Partial mode, a sensor is triggered and signals the panel to sound the alarm. The alarm will also be triggered under an emergency panic situation, when the panic button on the remote keyfob is pressed, or the alarm panel keypad registers a panic (long press 9 key). When an alarm is triggered the following actions will take place: - the siren will sound loudly (depending on your Alarm Type and Alarm Time settings).
10. Telephone Functions The alarm panel can operate as an ordinary telephone to make and answer GSM voice calls. It features a built in speakerphone with echo-cancelling to allow hands free conversation. 10-1 Calling and Answering 10-1-1 Making a call: Simply enter the number keys then press TEL key to call. Press TEL key again to hang up. 10-1-2 Answering a call: A ringing tone will sound when someone calls. Press the TEL Key to answer, and press it again to hang up.
3. Enter PIN + 15 + PARM to start the binding process. The DISARM LED will start to blink for 30 seconds with a beep tone. 4. Within 30 seconds, set the device to enter binding mode using its learn-key/ tamper button. Refer to the device’s user manual for details. For RFID tags, simply swipe it in front of the alarm panel in the area above the siren. 5. If a device is successfully added, the DISARM LED will turn on for 1 second along with a long beep sound. 6.
13. Troubleshooting 13-1 Basic Troubleshooting 13-1-1 The alarm panel cannot register with a GSM host (GSM Net LED flashes rapidly): a. SIM card not inserted or bad contact. b. SIM card needs to be unlocked before use (use a mobile phone to setup) to cancel the input of PIN code or PUK code. c. Change the position of the HA788GSM. d. Remove AC power and batteries and insert the SIM card again. e. Make sure the SIM card is not expired.
Specifications Operating temperature range Operating humidity Input rating Battery type Transmission range Frequency range GSM band -10°C to 50°C 85% RH at 30°C 9V DC 1A Li-ion cell 2000mAh 3.7V Outdoors >150m (Open space) for front and sides 868.35 MHz 850/900/1800/1900 MHz ** Specifications are subject to change without notice CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
Appendix A: Touch Keypad Operation Table Function ARM Mode Enter Key Explanation Enter PIN code + Exit Delay: Arm Key LED flashes and beeps (faster beeps at last 5 second countdown) For HA70F outdoor solar siren Keys 1 – 8 LEDs will display siren DIP Switch positions.
No delay: alarm will sound immediately without any preset delay Enter PIN code + 15 + 0 + Enter PIN code + 15 + 1 + Security Mode 0 Sensor activated only when Fully arm Sensor will not be activated in Partial Arm.
Appendix B: SMS commands These are the type of SMS commands the alarm panel receives and its confirmation message sent back to user.
Get Zone 1 Name Change Zone 1 Name Get Zone 2 Name Change Zone 2 Name 91 Zone1 Name: Entrance Door Sensor1 92 Zone2 Name: Entrance Door Sensor2 (Note 2) (Note5) Zone1 Name: Zone1 Use result from Get command, do Set Zone Name Successfully SMS Forward-> Edit->Send back Set Siren Volume (Note 2) (Note5) Get Siren Alarm Duration Zone2 Name: Zone2 Use result from Get command, do Set Zone Name Successfully SMS Forward-> Edit->Send back …same for Zone Names 3 ~ 9 Get RFID Tag Names Change RFID Ta
Appendix C: SMS Alerts Remote keyfob Panic List of SMS alert messages automatically sent by the alarm panel when certain event occurs.
