Quick Start Guide
Good Signal
Icon Status Desciption
Weak Signal
No Sevice
Full Power
Low Power
The number of clients connect to WIFI
Press menu button to select next
Press power button to confim
The icon changes from low to high repeatedly
to indicate that the battey is charging
Signal
Battey
WIFI
Next
OK
0
NEXT
OK
The default username and password can be
both referred to printed label from the
packing box.
Choose Advanced Settings → Wi-Fi
→ WLAN Settings.
In the General Settings list, set Wi-Fi
Enable or Disable.
In the SSID Profile list, change the
SSID, such as: "LTE-My MIFI".
To ensure data security, it is
recommended that you change the Wi-Fi
password.
Click Submit to save the settings.
Click Submit to save the settings.
Welcome to the SMC Series
SMC Seies LTE-A hotspot provides
consistent access to LTE networks,
including most operators and Pivate LTE
spectums. It allows multiple end users and
mobile devices to share 4G mobile
broadband Intenet connection from
anywhere.
SMC Series
Quick Start Guide
Device Architecture
LCD Screen
Power Button
USB
Menu Button
LED Light
Working Environment
Icon Definition
Power
Consumption
＜ 2.5W
5V/2A
Operating
Temperature
Storage
Temperature
Humidity
-10˫ ~ 45˫
-20˫~ 70˫
5% ~ 95%
Charging
Hardware Configuration
Remove the cover of unit and the
battery
Push the SIM card cover back and
open it upposition.
Place the SIM card in the correct
direction.
Close the SIM card cover and push
Place the battery then close the
cover .
Step1
Step2
Step3
Step4
Step5
Install SIM Card
Instructions
1.
Press power button 3s to
power on MIFI, or 5s to power
off MIFI
2.
1.Enter menu setting
2.Select next menu
Connect to the Network
It takes several seconds to connect to LTE
network. The screen will show different
status as follow.
1. It will show SIM not ready if MIFI does not
detect the SIM
2. The screen will show No service when
does not connect to network.
3. The screen will show connected when
LTE network connect successfully.
Login to the Web Management Page
Launch the web browser, enter
http://192.168.1.1 in the address bar, and
press Enter.
Login to the web management page
via USB cable or wirelessly.
Software Configuration
Step2
Step1
Enter the username and password,
and click Login.
Step3
Step3
can login to the web management page.
LTE Settings
Choose Advenced Settings >
Network>APN Settings.
On APN Settings page, you can
!#$&
Step1
Step2
Step3
If the problem persists, please contact
the authorized local service suppliers.
Fails to login the web management page
Please make sure MIFI is powered on
Please make sure the login password is
correct
Please check if PC get IP successfully.
If the problem persists,please contact
the authorized local service suppliers.
FCC Regulations:
§ 15.19 (a)(3)
This mobile MIFI complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation
§ 15.21
! '
party responsible for compliance could void the user‘s authority to
operate the equipment.
§ 15.105 (b)
This mobile phone has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician
for help.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment.
The device has been tested for use against the body with
*'+;+<!
= !
satisfying RF exposure compliance.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
FAQs
1 2
3 4 5
6
7
8
9
10 11 12 13
MIFI is not powered
Please make sure it is full battery.
Please press the power button more than
3s.
If the problem persists, please contact
the authorized local service suppliers.
Unable to connect to network
Please make sure the SIM is insert
successfully.
Please check if the unit is placed in an
open area.
If the problem persists, please contact
the authorized local service suppliers.
Unable to connect to WIFI
Please check if the WIFI is enable.
Please check if the WIFI password
correct.
Packing List
SMC Seies USB Cable
SMC S i
Step2
Step3
Step4
Step5
WLAN Settings
Step1
Considering RF effect, we would
recommend you to keep it away from 20
cm when using our SMC series.