uControl User Guide Key Fob Draft April, 2010
© 2006, 2007, 2008, 2009, 2010 uControl, Inc. The uControl logo, uControl, Inc., and all other uControl products and technology names are trademarks or registered trademarks of uControl, Inc. All other products or services mentioned herein are trademarks of their respective companies.
Table of Contents UNDERSTANDING AND USING THE KEY FOB ......................................................................................... 1 ADDING KEY FOBS TO SYSTEM ................................................................................................................ 5 SETTING A KEY FOB TO DEFAULT ...........................................................................................................
Understanding and Using the Key Fob A key fob is a mobile tool that lets you arm and disarm your system with the touch of a button. To use the key fob, press the button approximately 1.5 seconds until the LED flashes. See Table 1 for more information. KNOWN ISSUE: Management Portal might not show all key fobs in the System Status → Peripherals tab.
Table 1: Troubleshooting the Camera Installation Action Button Icon LED Display Flashes red once and then lights red for three seconds Arm System in Arm Stay Mode Description Used when everyone is leaving the house. Alarm trips immediately if a monitored Perimeter zone (non-entry/exit door or window) is opened. Interior motion detectors are armed.
Table 1: Troubleshooting the Camera Installation Action Button Icon Arm System in Arm Away Mode LED Display Flashes red once and then lights red for three seconds Description Used to arm the system when there are still people in the premises. Alarm trips immediately if a monitored Perimeter zone (non-entry/exit door or window) is opened. Interior motion detectors not armed. Entry/Exit zones start an Entry Delay Exit Delay starts when the system is armed.
Table 1: Troubleshooting the Camera Installation Action Button Icon System Status Error Condition N/A LED Display Description Flashes red once to indicate that it has contacted the system then: Tells whether the system is armed or disarmed Lights green for three seconds if the system is disarmed Lights red for three seconds if the system is armed.
Adding Key Fobs to System When a uControl key fob is removed from the box, it is already defaulted and ready to add to the SMA system. To add (pair) a key fob to an SMA Gateway: 1. After Activation: a. Log into the Settings widget using the Installer key pad code. b. Touch Key Fobs & Pads → Add Key Fob. During the Activation process: Eventually the Add Key Fob screen is displayed in the TouchScreen, Touch No I do not want to add a Key Fob and then Next to skip this step.
2. Install the battery in the key fob. Img_1424.mov Figure 1: Double-click to View Example of How to Install the Battery The LED blinks several times every five seconds. This means that the key fob is in Search mode and can be paired with the SMA Gateway device. Img_1425.mov Figure 2: Double-click to View Example of Key Fob in Search Mode If the key fob does not blink, it means that: The key fob is not defaulted (see page 8 for how to default the device).
. Touch the icon of a key fob that needs configuring. A keyboard screen is displayed to type a name for zone of the selected key fob. 11. Touch Done to enter the new name. The Configure Wireless Key Fobs screen is displayed again. 12. Repeat steps 10 through 11 for each key fob. 13. Click Next to continue. If you are adding the key fobs after Activation, the Settings widget menu is displayed. If you are adding the key fobs during Activation, the Add Key Pads screen is displayed.
Setting a Key Fob to Default Note: The SMA Gateway can only locate key fobs that are in Search mode and not currently paired with it. After a couple minutes, the key fob will drop out of Search mode to save battery power. If this happens, you will have to restart this procedure. To set a key fob to factory defaults: 1. If the key fob has already been added (paired) to the current TouchScreen, delete it (see page 10) 2. Gently pry the case apart and remove the PCB 3. Remove the battery and the button pad.
Img_1424.
Delete a Key Fob from the SMA System To delete a key fob from the SMA system: 1. From the Installer Settings Menu, touch Key Fobs & Sirens → Delete Key Fob. The Delete a Key Fob screen is displayed with images representing the key fobs currently installed to the SMA system. 2. Touch the image for the installed camera. A confirmation message is displayed: Are you sure you want to delete . 3. Touch Yes. The key fob image is removed from the Delete a Key Fob screen.
