« AN | Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISOMERIC, Japan Industrial Standards and other safety regulations*2).
A AIR COMBINATION Safety Instructions The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything Is unclear, contact your nearest sales branch. Limited warranty and Disclaimer/Compliance Requirements The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance Requirements”.
[ Design PAN Warning Q Air combination (D If any leakage isn't permitted due to ambient environment or fluid other than air is used, contact SMC. (2) External parts including the bonnet(materialpolyacetal), bowl, the sight dome{materiakpolycarbonate) are made of resin.
| Installation + Adjustment AN Warning O Air combination {I Connect the air combination ensuring the direction of “IN” and “QUT” for air direction or an arrow. Wrong connection lead to cause malfunction. @) Install vertically so that outlet of drain would turned downward. Use with the outlet of drain turned lateral or upward causes malfunction. @ Make a space to provide easy access at the bottom when replacing element or draining. For dimensions of the space, refer to Quayside dimensions.
@ Hold the female screw side and screw in piping with recommended tightening torque. Insufficient tightening torque lead to cause loose piping or sealing failure. Excessive torque may {ead to cause screw breakage. Tightening without holding female screw side applies excessive force to the piping bracket which lead to cause breakage. Recommended tightening torque _ Unit:N+m Screw MS 128 124 348 172 3/4 1 Morgue *1 1~9 12~14 | 22~24 | 28~30 | 28~30 | 36~38 *1:After tightening fitting, tighten approx.
7. TROUBLESHOOTING QO Air combination {Connection part) Leak retainer, (See 9. How to replace “assembly procedure for the morgue) Trouble Possible cause Remedy Subjected Demarcation] Phenomenon model Connection part | 1, Damaged packing. 1. Replace the packing, has ales. 1p | jocoseness of bolt for connecting |2. Tighten additionally with specified torus. |, QO For each component, refer to its operation manual. 8.
9. HOW TO REPLACE 2 Warning Before replacement, ensure that the regulator is not pressurized. Rotate the pressure adjusting handle of regulator to zero. After replacement, ensure that specified function is satisfied and external leakage is not found before starting operation. QO Air combination Model: AC * ~60 * Process Procedure Tools Check item Disassembly] (1) Remove piping connected to the component. to be replaced as necessary. @ Loosen hexagon socket head bolts.
How to connection new module (0) Count the product(F,R or L) to the interface of spacer with bracket, @ Push the retainer to the product. (@Hang the lever pin on the retainer. (@ Tighten the screw on the retainer. {Step 3 is to fiy the product to the module completely.
SPACER ASSEMBLY WITH BRACKET Hexagon socket head cap screw SPACER ASSEMBLY Retainer C Plate spring Hexagon socket head cap regress Packing Retainer A Lever pin
10. DIMENSIONS For the part indicated by each symbol refer to page 16 ~ 1JACI0~60 Model Port size ACT MEX AS AC iota bowl Soil vor wih veal sau A ~ BOA Model | Port size x0. o1 145 | 238] 92 i 9; 110 110 198 | 409) 175] 110 Drain Metal 208 48 A ~~ Model Port size ACTS M5%0.8 nls A | 83 | 114/265 40 1/4: 16 [3 75 186 | 264] 43 77 20 ‘Semi~standard Grain guide | Metal 0 114 Rosa be ith br sve) Roa ba er | Standard Act Pressure 6 N Pia 26 | 194 194 6.
IACCOCA C: ACA ACHOO-O! Port size AC10D~40D Modal ACCORD A ACADIA-0i Mods! Port size 1/4 1/43/8172 3/4 Barb B 209 A Pressure B 114265) 143] yal 1 64 | 285 go 146] 31 87 41 135 308 725 185] 36 [75 | 77.5 50 | 8145 | aa ]12] 74] 35 3 ‘Serine-standard Pressurization gauge mounting position is above piping Train guide | Malta bowl] Data an vt ve aug tenser for AC20C only, B Note) For barb fitting, drain guide, metal 11d — bowl or level gauge), different body length (B dimension) 1 178 is adopted.
AC-20 Gauge ort size op sc Port size a gur Gauge 7 x = (option) “ . Square tee poe segue Option AIR Soe FILTER LUBRICATOR #2 ® = Gauge A port size p ao Port size hfe Ef 8 OU post in of aut wht Nigel | Gauge : * (option) i square type U gauge [CEA ° H pain © w= ar AIR REGULATOR So FILTER LUBRICATOR AC. AC AC. AC. AC. AC-06. AC. AWACS, ACT Auto drain Auto drain ital ool will, .
Por Port size port size Semarang Gauge Sa option} — Saussure type Le gauge {Option) ® N rain Drain Se © 0 AIR MIST REGULATOR 2g FILTER SEPARATOR EX] 5 = AC25C-30C-40C A Gauge pore size £ F = port size Q G, Parr size SHH Gauge Id Option? “ i | Square type — sage “g Fs option) Drain Oran AIR MIST REGULATOR £3 FILTER SEPARATOR = z 2 ACZ0C AC25C, AC30C. ACACIA, AC4A0C-06 Tm AUTO drain Ag to drain teal Boil will, aa DTI COCKS Ution)™ ry 5 “Metal bowl "hg py (Metal bowl fa rain guideline Sine 1530.
DoE on B edition + AWACS and ACACIA addition. = Option M and E1~E£4 addition. Attachment V1 addition. » SMC Corporation 4-14-1, Nonstandard, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5208 6362 URL hitpJfwww.smoworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.