Datasheet

300
200
100
50
40
30
20
10
5.0
4.0
3.0
2.0
1.0
0 50 100
300
200
100
50
40
30
20
10
5.0
4.0
3.0
2.0
1.0
0 50 100
Allowable lateral load at rod end (N)Allowable lateral load at rod end (N)
Cylinder stroke (mm)
Cylinder stroke (mm)
Retaining Ring Installation/Removal
Caution
Mounting
Warning
1. For installation and removal, use an appropriate pair of pliers (tool
for installing a type C retaining ring).
2. Even if a proper plier (tool for installing a type C retaining ring) is
used, it is likely to inflict damage to a human body or peripheral
equipment, as a retaining ring may be flown out of the tip of a plier
(tool for installing a type C retaining ring). Be much careful with the
popping of a retaining ring. Besides, be certain that a retaining ring
is placed firmly into the groove of rod cover before supplying air at
the time of installment.
Do not apply reverse torque to the piston rods sticking out from
both sides of this cylinder at the same time. The torque makes
connection threads inside loosen, which may cause an accident
or malfunction.
Install or remove loads while the piston rod width across flat is
secured. Do not fix the other side of the piston rod width across
flat and apply reverse torque.
ø100
ø80
ø63
ø50
ø40
ø32
ø25
ø20
ø16
ø12
ø100
ø80
ø63
ø50
ø40
ø32
ø25
ø20
ø16
ø12
Note 1) ø32 without auto switch: M5 is used for 5 mm strokepiping dimension.
Thus, do not enter a symbol for the port thread type.
Note 2) The dimension of the ø32-5 mm stroke with built-in one-touch fittings is the same as that of the 10 mm
stroke cylinder tube.
Note 3) One-touch fittings cannot be replaced.
With Auto Switch
12
16
20
25
32
40
50
63
80
100
CQ-L012
CQ-LZ12
CQ-L016
CQ-LZ16
CQ-L020
CQ-LZ20
CQ-L025
CQ-LZ25
CQ-L032
CQ-L040
CQ-L050
CQ-L063
CQ-L080
CQ-L100
CQ2-D
CQ2-DZ
CQ2-D
CQ2-DZ
CQ2-D
CQ2-DZ
CQ2-D
CQ2-DZ
CQ2-DZ
CQ2-DZ
CQ2-DZ
CQ2-DZ
CQ2-DZ
CQ2-DZ
CQ-F012
CQ-F016
CQ-F020
CQ-F025
CQ-F032
CQ-F040
CQ-F050
CQ-F063
CQ-F080
CQ-F100
Bore size (mm)
Mounting
Piping
Mounting
Piping
Through-hole (Standard)
Both ends tapped
Through-hole (Standard)
Both ends tapped
Built-in magnet
Built-in magnet
Rod end male thread
With rubber bumper
Rod end male thread
Pipe thread
Pipe thread
Built-in one-touch fittings
Note 3)
12



—
—
—


—
—
—
—
—
—
16



—
—
—


—
—
—
—
—
—
20



—
—
—





—

25



—
—
—





—

32



NPT1/8
G1/8
ø6/4
Note 2)





NPT1/8

40



NPT1/8
G1/8
ø6/4





NPT1/8

50



NPT1/4
G1/4
ø8/6





NPT1/4

63



NPT1/4
G1/4
ø8/6





NPT1/4

80



NPT3/8
G3/8
—





NPT3/8

100



NPT3/8
G3/8
—





NPT3/8

M5 M5 M5
M5
M5
M5
Note 1)
M5
Rc1/8
Note 1)
M5
Rc1/8
Rc1/8 Rc1/4 Rc1/4 Rc3/8 Rc3/8
Rc1/8 Rc1/4 Rc1/4 Rc3/8 Rc3/8
—
TN
—
TN
TF
PneumaticAir-hydro
Type Mounting Brackets/Part No.
Bore size (mm)
Foot
Note 4)
Model Flange
Without switch
With switch
Without switch
With switch
Without switch
With switch
Without switch
With switch
Note 4) When ordering a foot and compact foot brackets,
the required quantity will be different depending on
the bore size.
ø12 to ø25:
• Without switch: Order 2 pieces per cylinder.
• With switch: Order 1 piece per cylinder. (Part
number for a set of 2 foot brackets)
ø32 to ø100:
• Order 2 pieces per cylinder.
Note 5) Parts belonging to each bracket are as follows.
Foot, Compact foot, Flange: Body mounting bolts
Allowable Lateral Load at Rod End
Without Auto Switch
CQ-LC012
CQ-LCZ12
CQ-LC016
CQ-LCZ16
CQ-LC020
CQ-LCZ20
CQ-LC025
CQ-LCZ25
CQ-LC032
CQ-LC040
CQ-LC050
CQ-LC063
CQ-LC080
CQ-LC100
Compact
Foot
Note 4)
Series CQ2W
Compact Cylinder: Standard
Double Acting, Double Rod
Standard
Large Bore
Size
Long Stroke
Non-rotating
Rod
Axial Piping
Anti-lateral
Load
With End Lock
Water
Resistant
Auto SwitchMade to Order
With Auto
Switch
28