Datasheet

Ordering Example of Cylinder Assembly
3
Series CG1
Retaining
ring
Cylinder body
Retaining
ring
Pivot bracket
Retaining
ring
Retaining
ring
Clevis pin
(Put grease)
Cylinder
body
Pivot bracket
Clevis pin
(Put grease)
Cylinder body
Trunnion bolt (With
scotch grip) 4 or 5
times remounting
possible
Flat washer
Pivot bracket
Trunnion pin
(Put grease on the exterior.)
Auto switch
Clevis
Double knuckle joint
Pivot bracket
ø80, ø100ø20 to ø63ø20 to ø63
Follow the procedures below when mounting a
pivot bracket on the trunnion.
Mounting procedure for trunnion
Follow the procedures below when mounting a pivot bracket on the clevis.
Mounting procedure for clevis
Note 1) Order two foots per cylinder.
Note 2) Can be combined with the trunnion pin and the clevis.
Mounting D: Clevis
Pivot bracket N: Yes
Rod end bracket W: Double knuckle joint
Auto switch D-M9BW: 2 pcs.
∗ Pivot bracket, double knuckle joint and auto
switch are shipped together with the product, but
not assembled.
Cylinder model: CDG1DN20-100Z-NW-M9BW
Mounting
bracket
Order
q’ty
Bore size [mm]
Contents
20 25 32 40 50 63 80 100
Axial foot 2
Note 1)
CG-L020 CG-L025 CG-L032 CG-L040 CG-L050 CG-L063 CG-L080 CG-L100
2 foots,
8 mounting bolts
Flange 1 CG-F020 CG-F025 CG-F032 CG-F040 CG-F050 CG-F063 CG-F080 CG-F100
1 fl ange,
4 mounting bolts
Trunnion pin 1 CG-T020 CG-T025 CG-T032 CG-T040 CG-T050 CG-T063 — —
2 trunnion pins, 2 trunnion bolts,
2 fl at washers
Clevis 1 CG-D020 CG-D025 CG-D032 CG-D040 CG-D050 CG-D063 CG-D080 CG-D100
1 clevis, 4 mounting bolts,
1 clevis pin, 2 retaining rings
Pivot bracket
Note 2)
1 CG-020-24A CG-025-24A CG-032-24A CG-040-24A CG-050-24A CG-063-24A CG-080-24A CG-100-24A 1 pivot bracket
Segment Description Material Surface treatment
Mounting
brackets
Foot Carbon steel Nickel plating
Flange
Carbon steel (ø20 to ø63) Nickel plating
Cast iron (ø80, ø100) Nickel plating
Clevis
Carbon steel (ø20 to ø63) Nickel plating
Cast iron (ø80, ø100) Nickel plating
Trunnion pin
Trunnion pin Carbon steel Salt-bath nitrocarburising
Trunnion bolt Carbon steel Nickel plating
Flat washer Carbon steel Nickel plating
Accessories
Rod end nut Carbon steel Zinc chromated
Single knuckle joint
Carbon steel (ø20 to ø32) Nickel plating
Cast iron (ø40 to ø100) Zinc chromated
Double knuckle joint
Carbon steel (ø20 to ø32) Nickel plating
Cast iron (ø40 to ø100) Zinc chromated
Knuckle pin Carbon steel —
Clevis pin Carbon steel —
Pivot bracket
Carbon steel (ø20 to ø63) Nickel plating
Cast iron (ø80, ø100) Nickel plating
Mounting bolt Carbon steel Nickel plating
Retaining ring Carbon tool steel Phosphate coating
Mounting Brackets/Part No.
Mounting Brackets, Accessories/Material, Surface Treatment
∗ Maximum ambient temperature for the rod
boot itself.
Symbol Rod boot mater
Maximum operating
temperature
J
Nylon tarpaulin 70°C
K
Heat resistant tarpaulin 110°C
∗
Rod Boot Material
Mounting Procedure