Instructions for Use Washing machine
Thank you for your confidence in purchasing our washing machine, and congratulations on the excellent choice. Your new washing machine meets the requirements of modern treatment of laundry. It is rational in the consumption of energy, water and washing agents. Our appliances are friendly to the environment. Some of the materials may be recycled, others deposited or decomposed. To avoid pollution of environment, once your appliance is no longer useful, take it to your local authorized waste appliance dealer.
Description of washing machine 1. Front panel 2. Detergent dispenser 3. Door (depending on the model) 4. Filter lid • Model (WA63xxx, WA64xxx) Dimensions (w x d x h): 600 mm x 600 mm x 850 mm Depth with door open: 106 cm Weight (net): 90 kg Nominal voltage: 230 V, 50 Hz Power: 2300 W Max. load: 6 kg Power socket: (230 V, 50 Hz, 10 A) Water pressure: min. 0,05 MPa, max. 0,8 MPa Fuse: 10 A 155620 Technical information 5. Adjustable legs 6. Water outlet hose 7. Water inlet hose 8.
Cautions • Be sure to remove transport brackets prior • • • • • • • • • • • 155620 4 first use of the appliance. Attempted operation of the blocked machine may result in irreparable damage which is not covered by the manufacturer’s warranty! When connecting your washing machine to water supply, be sure to use brand new water inlet hose and appropriate sealing gaskets (attached). Do not locate the machine in a room with temperature below 0°C. Parts of the machine may be damaged if frozen.
• Before any transport block the machine by Before connecting the appliance read these instructions carefully. Repairing the failure arising from inappropriate connections or use of the appliance is not covered by the guarantee. The belt can be replaced by a servising engineer only, who incorporates an original spare part with the marking MIG OPTIBELT 6EPJ 1260, code 111622 or 6EPJ 1278 code 587612.
Installation and connection In removing the wrapping be careful not to damage the appliance with a sharp object. Package removal • Our appliances are packed in environmentally • Removal of transport brackets friendly materials which may be recycled, deposited or decomposed without any threat to the environment. To this end all wrappings are marked accordingly. • Move the pipes. • Loosen screws A at the rear of the machine (Fig. 1). • Remove the brackets B (Fig.
Leveling the appliance • Put the appliance in horizontal position by turning the adjustable legs. The legs are adjustable up to +/- 1 cm. The floor below the appliance should have concrete base, and must be dry and clean, otherwise the appliance may slide. • If you have a tumble dryer of the same dimensions, you can place it on top of the washing machine. To ensure correct operation of the appliance, water pressure inlet must be between 0,05 and 0,8 MPa.
Partial Aqua-stop (water stop system) In case of damage on the interior pipe, leaking is prevented by automatic closing system which stops water inlet to the machine. In such cases display A turns red. Inlet pipe must be replaced. Complete Aqua-stop In case of damage on the interior pipe, leaking is prevented by automatic closing system which stops water inlet to the machine. Security system also detects whether there is any water leakage within the interior of the machine.
The wall socket must be accessible at all times and must be equipped with an earth lead (in accordance with the local safety regulations). The permanent connection must be fitted by an authorized personnel only. Damaged mains power cable may be replaced only by the producer or his authorized personnel. Never plug the appliance into the electric shaver socket or hair dryer socket.
Operation A - program selector B - MENU knob C - SELECTION knob D - short program knob E - easy ironing knob Program selector F - START/PAUSE knob G - door knob (depending on the model) H - display Basic programs Partial programs Cotton Heavy duty Rinse Synthetics Softening Delicate Pumping water Wool Spinning Manual wash Jogging Mix 155620 Functional knobs Knob B (MENU) - Use this knob to scroll around main menu. Knob C (SELECTION) - Use this knob to scroll around main menu.
Before first use - Selecting language To change the language in which the information appear on the display, press simultaneously the key MENU (B) and SELECTION(C), and turn the program selector (A) from position “0” to the first program in clockwise direction (Cotton 95°C). The name of actually selected language appears on the display. Scroll down the selection of languages by pressing the SELECTION knob (C), until you find the desired language. Then turn the program selector back to position “0”.
symbols on the last page of these instructions). Washing machine operation - Load the laundry into the drum. Check that the drum is empty. - Close the door of the appliance. - Open the water inlet faucet. - Switch the machine on. 1. Name of the program, 2. Duration or time of day, 3. Symbols for activation of additional functions, 4. Water quantity in liters, 5. Spin RPM Program is selected by turning the program selector from the “0” position to the desired washing program.
selector (A) to the desired program. The display indicates the selected program, along with basic settings. With each basic program you may also select additional functions. Cotton: whites/colored Normally stained cotton and flax bed linen and underwear, table cloth, bathroom towels, top garments, etc. For heavily stained permanent press use the heavy duty program, or program with the pre-wash, or select soaking in case of stains.
Mix Special program for washing normally stained colored laundry made from various resistant fabrics at 40°C. - Selection of additional function ( , , , , , , , , , ,) The display always indicates only the menus with functions which are available for a particular program. Certain functions may not be selected at the same time (see Program /Additional Functions Chart). Our suggestion is to select first the additional functions with ‘Short program (D) and Easy ironing knobs (E).
in bold (spin RPM, extra rinse, more water, sound signal). Using the SELECTION knob (C) you may change settings. Activation of a particular function is confirmed by the relevant symbol appearing on the display. Function is deactivated by another pressing the SELECTION knob (C). Reduced spin RPM / Rinse hold Best recommended spin RPM for the selected program appear on the display.
for certain programs this function is available also for washing. Appropriately larger quantity of water is indicated by the display. Cold wash For washing less soiled or colour-sensitive clothes. Upon switching this function ON, the heating function of this cycle is switched OFF, therefore the whole program is adequately shortened. Each temperature related to a particular program (wool, cotton, delicates, etc.) corresponds to a particular period of cold wash.
SELECTION knob (C) on programs for cotton, synthetics, delicate and mixed laundry. Soaking This program is intended for removal of stubborn stains. In default setting the soaking function is off. It is engaged by pressing the SELECTION knob (C). Soaking time may be set from 1 h to maximum 6 hours, in 30 minute steps. At the end of the preset time the machine automatically starts the selected washing program.
SELECTION knob (C) until the required time to end the washing appears on display. Caution: If Clean water sensor is engaged, the program may last longer for extra rinsing time. In case you wish to change or suspend the end of washing time after starting the machine with the START knob (F), you may do so by pressing the MENU knob. The end of washing time appears; using the SELECTION button (C) reset the selected time.
Permanent disengagement of the function: a.) During the operation: - Keep the MENU knob (B) pressed for 4 seconds. - Stop the program by pressing the START/PAUSE knob (F). - Using the MENU knob (B) move to child lock option. - Press the SELECTION knob (C) to disengage the function. b.) After the program is completed: - Keep the MENU knob (B) pressed for 4 seconds.
Pumping the water out Use it when the washing program was interrupted or if pump stop function was engaged, and you only wish to pump the water out of the drum, without spinning. Spinning Aggressive spinning for non-delicate laundry at high spin RPM. Spin revolutions can be altered.
START knob (F) and the machine will finish the program with the spin, determined by that particular program. In case you would like to alter the washing program, turn the program selector to the position “0”, followed by the selection of rinse or merely pumping the water out. If a power failure occurs during the washing program, when the power is restored the machine will resume the execution of a program where it had been interrupted.
Permanent suspension - change of program By turning the program selector to the position “0” the program is permanently suspended. Consequently you may select a new program (see Program selection). • Failures Program is suspended in case a failure occurs. This is signalled by the relevant reading on the display and a sound signal (see cf. Troubleshooting).
- Now minutes start flashing; they are set the same way as hours. - Confirm setting by pushing the MENU knob (B). - Return the program selector back to “0” position. Set time is automatically saved. • Setting the Clean water sensor 155620 In order for the Clean water sensor to start working properly, it must be first calibrated with water that the washing machine is connected to.
Tips for washing and energy saving • Before washing sort out the laundry according to the type, degree of dirtiness and color resistance. • Prior selecting the washing program consult the • • • • • • • • • • • 155620 24 sewn tab with information on a particular piece of laundry (see Maintenance chart on the last page). Wash separately the new colored textile products for the first time. Wash heavily soiled laundry in small quantities and add more detergent.
Hardness scale Degree of hardness °dH(°N) m mol/l °fH(°F) p.p.m. 0-7 0-1,3 0-12 0-120 2 - Medium 7-14 1,3-2,5 12-25 120-250 3 - Hard 14-21 2,5-3,8 25-37 250-370 >21 >3,8 >37 >370 1 - Soft 4 - Extra hard In case of hard water add detergent according to the Chart for degree 1 and add appropriate quantity of water softener (see manufacturer’s instructions).
Cleaning and maintenance Disconnect the washing machine from the mains before cleaning! • The casing should be cleaned with soft cloth and mild detergent. • The interior of the drum and the door gasket is • cleaned by washing at 60°C without laundry and adding half quantity of detergent. If necessary, clean the detergent dispenser. Pull it out from its casing completely by pressing the flap (see Fig.). • If necessary, clean the cover of the bung under the running water.
• Wash it under running water using a brush, and dry it. Remove any leftover dried detergent from the bottom of the casing. • Clean frequently the water inlet hose screen under running water. • After each wash wipe the door rubber gasket. This will prolong its useful life. • Open the filter lid using flat screwdriver or similar tool. • Filter needs occasional cleaning, especially 155620 following heavily shaggy or old laundry. Before cleaning, drain any water from the machine via drain pipe.
• Turn it anti-clockwise, pull it out and clean under running water. • Insert the filter back as shown on the picture (arrow and pointer), and tighten by turning it in clockwise direction.
Failures If the washing machine identifies failures in the operation, it reports it immediately. Sound alarm is heard and the display reads ERROR. Number identifies the type of failure. In some cases you may attempt removing certain failures yourself (see the chart below), and the machine will continue to perform the operation after pressing the START knob (F).
Failure Possible cause Remedy The machine moves during operation. The machine is not properly leveled. Transport brackets are not removed. Level the machine with the adjustable legs. Remove transport brackets. The machine vibrates during the spin. Unevenly distributed laundry, especially with very small quantities (for ex. only the bathrobe). This is normal, the machine will reduce the RPM if vibrations are too strong. Wash larger quantity of laundry. Excessive foaming during washing.
Failure Possible cause Remedy Detergent residues in the dispenser. Low water flow pressure. Some detergents may stick to the dispenser rather hard if it is wet. • Clean the inlet pipe screen. • Wipe the dispenser prior loading detergent. Softener is not completely rinsed, or water is left in the dispenser dish. Sucking cover is not correctly Clean the dispenser and firmly fix positioned or is clogged. the cover to its place. Washing time is longer than usual.
Tables Program chart - 6kg 6 60 Cotton 6 40 Synthetics 3 60 Synthetics 3 40 Synthetics max. 1800 max. 1000 1400 - 1800 60 1000 - 1300 6 Cotton heavy * RPM 800 - 900 Cotton RPM 1400 - 1800 95 Energy cons. kWh 1000 - 1300 6 Water cons. l 48 48 2,10 2,10 2,05 45 1,19 1,19 1,15 1,14 1,14 1,02 800 - 900 Temp. (°C) Cotton Type of laundry Spin (RPM) Max.
Higher water level Pre-wash Soaking l/l l/l l l l l/l l/l l l l l/l l/l l l l l Delicate l l/l -/l l l l l Wool l l/l l Manual wash l l/l l Easy iron Cotton l l Synthetics l l Cotton heavy Jogging Mix l Spin speed Rinse hold Basic programs Short program / Program l l/l -/l l l/l l/l l Cold wash Extra rinse / clean water sensor Program chart/ Additional functions l l l l Partial programs Rinse l/- Softening l/- Pumping water Spin l/- 15562
Maintenance chart Normal wash Delicate wash Whitening Max. washing temp. 95°C Max. washing temp. 40°C Max. washing temp. 60°C Whitening in cold water Max. washing temp. 30°C Manual washing Washing not allowed Whitening not allowed Ironing Hot iron max. 200°C Hot iron max. 150°C Hot iron max.
PS PG3,4 OEM SMEG 155620/en (02-06)