Instruction Manual

16
USER INSTRUCTIONS
EN
EN
15
USER INSTRUCTIONS
FAULT DESCRIPTION
E6
Water pump-out malfunction
The appliance does not pump out the water or does so
incorrectly. Make sure the drain hose is not kinked or
crushed and that the siphon and fi lters are not clogged.
If the problem persists, contact the technical assistance
service.
E7
Turbine fl ow-regulator malfunction
(only for models fi tted with this feature)
The appliance is unable to precisely measure the
quantity of incoming water. Interrupt the current program
and switch off the dishwasher. Switch it back on again,
program a new cycle and press start. If the problem
persists, contact the technical assistance service.
E8
Alternate washing system malfunction
Interrupt the current program and switch off the
dishwasher. Switch it back on again, program a new
cycle and press start. If the problem persists, contact
the technical assistance service.
E9
Water intake system malfunction
Contact the technical assistance service.
Tab. 4-01b
Light off Light on
Light fl ashing
If an alarm situation occurs, the dishwasher interrupts the current program and
signals the fault.
sm r a l A • E1, E2, E3, E4, E8, E9 immediately terminate the current program.
• Alarms E5, E6 interrupt the current program and, after the problem has been
eliminated, resume the cycle.
• Alarm E7 is displayed at the end of the cycle which, however, is completed
given that it does not jeopardize the operation of the dishwasher.
:mr a l a na ” t ese r “ oT
s i h t t A . n i aga f f o kcab dna no ecna i l ppa eh t hc t i ws r o , r ood eh t eso l c r o nepo •
point, the dishwasher can be programmed again.
- r eS ecna t s i ssA l ac i nhceT dez i r oh t uA eh t t ca t noc , s t s i s r ep t l ua f eh t f I
vice.
EN
15
USER INSTRUCTIONS
FAULT DESCRIPTION
E6
Water pump-out malfunction
The appliance does not pump out the water or does so
incorrectly. Make sure the drain hose is not kinked or
crushed and that the siphon and fi lters are not clogged.
If the problem persists, contact the technical assistance
service.
E7
Turbine fl ow-regulator malfunction
(only for models fi tted with this feature)
The appliance is unable to precisely measure the
quantity of incoming water. Interrupt the current program
and switch off the dishwasher. Switch it back on again,
program a new cycle and press start. If the problem
persists, contact the technical assistance service.
E8
Alternate washing system malfunction
Interrupt the current program and switch off the
dishwasher. Switch it back on again, program a new
cycle and press start. If the problem persists, contact
the technical assistance service.
E9
Water intake system malfunction
Contact the technical assistance service.
Tab. 4-01b
Light off Light on
Light fl ashing
If an alarm situation occurs, the dishwasher interrupts the current program and
signals the fault.
sm r a l A • E1, E2, E3, E4, E8, E9 immediately terminate the current program.
• Alarms E5, E6 interrupt the current program and, after the problem has been
eliminated, resume the cycle.
• Alarm E7 is displayed at the end of the cycle which, however, is completed
given that it does not jeopardize the operation of the dishwasher.
:mr a l a na ” t ese r “ oT
s i h t t A . n i aga f f o kcab dna no ecna i l ppa eh t hc t i ws r o , r ood eh t eso l c r o nepo •
point, the dishwasher can be programmed again.
- r eS ecna t s i ssA l ac i nhceT dez i r oh t uA eh t t ca t noc , s t s i s r ep t l ua f eh t f I
vice.
EN
15
USER INSTRUCTIONS
FAULT DESCRIPTION
E6
Water pump-out malfunction
The appliance does not pump out the water or does so
incorrectly. Make sure the drain hose is not kinked or
crushed and that the siphon and fi lters are not clogged.
If the problem persists, contact the technical assistance
service.
E7
Turbine fl ow-regulator malfunction
(only for models fi tted with this feature)
The appliance is unable to precisely measure the
quantity of incoming water. Interrupt the current program
and switch off the dishwasher. Switch it back on again,
program a new cycle and press start. If the problem
persists, contact the technical assistance service.
E8
Alternate washing system malfunction
Interrupt the current program and switch off the
dishwasher. Switch it back on again, program a new
cycle and press start. If the problem persists, contact
the technical assistance service.
E9
Water intake system malfunction
Contact the technical assistance service.
Tab. 4-01b
Light off
Light on
Light fl ashing
If an alarm situation occurs, the dishwasher interrupts the current program and
signals the fault.
sm r a l A • E1, E2, E3, E4, E8, E9 immediately terminate the current program.
• Alarms E5, E6 interrupt the current program and, after the problem has been
eliminated, resume the cycle.
• Alarm E7 is displayed at the end of the cycle which, however, is completed
given that it does not jeopardize the operation of the dishwasher.
:mr a l a na ” t ese r “ oT
s i h t t A . n i aga f f o kcab dna no ecna i l ppa eh t hc t i ws r o , r ood eh t eso l c r o nepo •
point, the dishwasher can be programmed again.
- r eS ecna t s i ssA l ac i nhceT dez i r oh t uA eh t t ca t noc , s t s i s r ep t l ua f eh t f I
vice.
Wash motor pump does not work
E11
• E11: Contact the after-sales service.
EN
15
USER INSTRUCTIONS
FAULT DESCRIPTION
E6
Water pump-out malfunction
The appliance does not pump out the water or does so
incorrectly. Make sure the drain hose is not kinked or
crushed and that the siphon and fi lters are not clogged.
If the problem persists, contact the technical assistance
service.
E7
Turbine fl ow-regulator malfunction
(only for models fi tted with this feature)
The appliance is unable to precisely measure the
quantity of incoming water. Interrupt the current program
and switch off the dishwasher. Switch it back on again,
program a new cycle and press start. If the problem
persists, contact the technical assistance service.
E8
Alternate washing system malfunction
Interrupt the current program and switch off the
dishwasher. Switch it back on again, program a new
cycle and press start. If the problem persists, contact
the technical assistance service.
E9
Water intake system malfunction
Contact the technical assistance service.
Tab. 4-01b
Light off Light on
Light fl ashing
If an alarm situation occurs, the dishwasher interrupts the current program and
signals the fault.
sm r a l A • E1, E2, E3, E4, E8, E9 immediately terminate the current program.
• Alarms E5, E6 interrupt the current program and, after the problem has been
eliminated, resume the cycle.
• Alarm E7 is displayed at the end of the cycle which, however, is completed
given that it does not jeopardize the operation of the dishwasher.
:mr a l a na ” t ese r “ oT
s i h t t A . n i aga f f o kcab dna no ecna i l ppa eh t hc t i ws r o , r ood eh t eso l c r o nepo
•
point, the dishwasher can be programmed again.
- r eS ecna t s i ssA l ac i nhceT dez i r oh t uA eh t t ca t noc , s t s i s r ep t l ua f eh t f I
vice.
QuickTime
end
QuickTime
Sanitized
1131410 6789432 5
½
1112
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
end
Auto
E1
E2
E3
E4
E5
E6
E7
E8
E9
E11