Contents 1. INSTRUCTIONS FOR PROPER USE ______________________________________ 19 2. SAFETY INSTRUCTIONS _______________________________________________ 20 3. KNOW YOUR HOB ____________________________________________________ 21 4. BEFORE FIRST USE___________________________________________________ 21 5. COOKING ZONES_____________________________________________________ 22 6. DESCRIPTION OF CONTROL ON THE FRONT CONTROL PANEL______________ 23 7.
Instruction for proper use 1. INSTRUCTIONS FOR PROPER USE ELECTRICAL CONNECTION: PLEASE REFER TO INSTALLATION INSTRUCTIONS FOR THE GAS & ELECTRICAL SAFETY REGULATIONS AND THE VENTILATION REQUIREMENTS. IN YOUR OWN INTEREST, AND THAT OF SAFETY, IT IS THE LAW THAT ALL GAS AND ELECTRICAL APPLIANCES BE INSTALLED AND SERVICED BY COMPETENT PERSONS, WHO WILL COMPLY WITH THE RELEVANT STANDARDS AND REGULATIONS. SMEG REGISTERED INSTALLERS UNDERTAKE TO WORK TO SATISFCTIORY STANDARDS.
Safety instruction 2. SAFETY INSTRUCTIONS INSTRUCTIONS FOR THE INSTALLER: THESE ARE INTENDED FOR THE QUALIFIED TECHNICIAN WHO MUST INSTALL THE APPLIANCE, SET IT FUNCTIONING AND CARRY OUT AN INSPECTION TEST. IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES. WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS.
Instructions for the user 3. KNOW YOUR HOB Glass surface of the appliance Single cooking zone Dual oval cooking zone Dual round cooking zone Timer controls Control panel Triple cooking zone Heating zone NOT ALL COMPONENTS DESCRIBED ARE PRESENT ON ALL MODELS 4. BEFORE FIRST USE Do not leave the packing in the home environment. Separate the various waste materials and take them to the nearest special garbage collection centre. Before cooking for the first time, the hob has to be cleaned.
Instructions for the user 5. COOKING ZONES The appliance features 4/5 cooking zones of different diameter and power. Their position is clearly indicated by circles and the heat given off is defined by the markings on the glass surface. The 5 cooking zones are of the HIGH-LIGHT type and come on after a few seconds of being activated. Heating intensity can be adjusted by means of the knobs located on the front panel from a minimum setting of 1 to a maximum setting of 6/9 (Depending on models).
Instructions for the user 6. DESCRIPTION OF CONTROL ON THE FRONT CONTROL PANEL All the hob controls are grouped together on the front panel. The table below provides a description of the symbols used.
Instructions for the user 7. USE OF THE COOKING HOB 7.1 Hobs with knobs 7.1.1 Single cooking zones Each knob shows the cooking zone it is for. identifies the knob that For example, the symbol controls the rear right-hand cooking zone. To heat, turn the knob to the desired position (1 to 6). Adjustment is continuous so that the appliance also operates at any intermediate value. 7.1.2 Dual cooking zones Each knob shows the cooking zone it is for.
Instructions for the user 7.2 Hobs with touch-control buttons When an icon is pressed the unit beeps to confirm. To operate the panel of the hobs equipped with touch-controls, lightly press the icons printed on its surface. On first connection to the electrical mains, an operating check will be carried out automatically and all the indicator lights will come on for a few seconds. 7.2.1 Switching on the hob symbol is pressed twice the hob When not in use, all hob components will be switched off.
Instructions for the user 7.2.8 Timer (on some models only) Some models are equipped with a 1 to 99-minute cooking timer. To use the timed cooking, first set the power level by following the instructions given in paragraphs “7.2.2 Single Cooking Zones” and “7.2.3 Dual Cooking Zones”. key to enable the functions), press Now, with the hob NOT locked out (if it is locked out, press the the symbol .
Instructions for the user 7.2.14 Switching off To switch off the hob, press ; this switches off all the cooking zones even if they are operating, and the hob is completely switched off. If the cooking zones are hot, 5 seconds after the switch-off the " " appears, warning of the residual heat. 7.3 Cooking tips The table below shows the power values which can be set, with the relative type of food alongside. Setting may vary depending on the amount of food and personal taste.
Instructions for the user 8. CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. 8.1 Cleaning the ceramic hob The hob should be regularly cleaned; preferably after every use, once the residual heat warning lights have gone off. Smudges from aluminium-bottom pans can be easily cleaned off with a cloth dampened in vinegar. Remove any burnt residues after cooking with the scraper provided; rinse with water and wipe dry with a clean cloth.
Instructions for the installer 10. INSTALLATION 10.1 Technical information Hob type Electrical connections HOB RATING Maximum electrical power DIMENSIONS OF THE HOB Width (mm) Depth (mm) See rating plate 220-240V~ 50/60Hz / 380-415V 2N∼ 50/60Hz / 380-415V 3N∼ 50/60Hz Electric See rating plate 290 510 595 510 720 510 900 510 10.2 The rating plate Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing.
Instructions for the installer For operation on 380-415 V 3N∼: use an - H05V2V2-F type five-core cable (5 x 1,5 mm2). For operation on 380-415 V 2N∼: use an - H05V2V2-F type four-core cable (4 x 2,5 mm2). For operation on 220-240 V 3∼: use an - H05V2V2-F type four-core cable (4 x 2,5 mm2). For operation on 220-240 V∼: use an - H05V2V2-F type three-core cable.
Instructions for the installer 10.4 POSITIONING OF THE HOB The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear edge.
Instructions for the installer MOD. 60 CM MOD. 77 CM The diagrams illustrate the cutting sizes and additional shaping required for the installation hole if you decide to install the hob flush with the work-top surface. The work-top hole and shaping dimensions are purely guideline; it is essential to refer to your actual ceramic hob before making any cuts.