DISHWASHER INSTALLATION INSTRUCTIONS
EN CONTENTS Contents 1 INTRODUCTION ........................................................................................ 3 2 SAFETY INFORMATION ............................................................................. 5 3 INSTALLATION MATERIAL ......................................................................... 8 3.1 Kit supplied with dishwasher ...................................................................... 9 4 DIMENSIONS OF DISHWASHER .........................................
EN CONTENTS 2
EN INTRODUCTION 1 INTRODUCTION Thank you for choosing one of our products. To install this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to installation of the appliance. The texts are easy to understand and are complete with detailed illustrations. This user-friendly manual will provide answers to all your questions about installation of the dishwasher.
EN INTRODUCTION Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. DANGER OF ELECTROCUTION. This symbol highlights information and warnings of an electrical nature which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. Tab.
EN WARNINGS 2 SAFETY INFORMATION THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE.
EN WARNINGS CHECK THAT THE VOLTAGE, FREQUENCY AND PROTECTION OF THE DOMESTIC MAINS POWER SUPPLY MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE. TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHER. DO NOT LEAVING DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME. SEPARATE THE VARIOUS PACKAGING MATERIALS AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE.
EN WARNINGS NECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE. DO NOT ATTEMPT TO REPAIR THE APPLIANCE. DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING, WITH CONSEQUENT FIRE HAZARD.
EN INSTALLATION INSTRUCTION 3 INSTALLATION MATERIAL To install the dishwasher correctly, the following materials are required: • Phillips screwdriver (ref. A fig. 3-01); • spirit level (ref. B fig. 3-01); • tape measure (ref. C fig. 3-01); • compass saw (ref. D fig. 3-01); • pencil (ref. E fig. 3-01); • file (ref. F fig. 3-01); • 13 mm open-ended wrench (ref. G fig. 3-01); • plumbing pliers (ref. H fig. 3-01); • drill (ref. I fig. 3-01); • safety gloves (ref. L fig. 3-01). B A C D F E H G I L Fig.
EN INSTALLATION INSTRUCTION 3.1 Kit supplied with dishwasher The kit supplied with the dishwasher comprises: • 1 adhesive steam guard (depending on the model) (ref. A fifig. g. 3-02); guard (depending on the model) (ref. B fig.(ref. 3-02)*; • 1 steel steam adhesive steam guard (depending on the model) B fig. 3-02)*; • 1 template for door panel (ref. C fifig. g. 3-02); • 2 hooks for door panel (ref. D fifig. g. 3-02); • 8 screws for securing the door panel hooks (ref. E fifig. g.
EN INSTALLATION INSTRUCTION 4 INGLESE DIMENSIONS OF DISHWASHER (See fig. 4-01) A (height) 82 cm ¸ 89 cm B (width) C (depth) 82 cm - 89 cm 59.7 cmcm ÷ 59,9 cm cm 59,7 ¸ 59,9 32-9/32" ¸ 35-3/64" 32-9/32” - 35-3/64” 23-1/2” ÷ 23-37/64” 23-1/2" ¸ 23-37/64" 86 cm ¸ 93 cm 33-35/64"¸36-39/64" 55 cm 21-21/32" 55 -cm 60 21-21/32” cm - 23-5/8" * *STX models Tab. 4-01 A: according to the models C: 23-5/8" only for STX models A C B Fig.
EN INSTALLATION INSTRUCTION 5 INSTALLATION AND HOOK-UP DURING INSTALLATION, TAKE CARE NOT TO INJURE YOURSELF ON THE SHARP EDGES OF THE APPLIANCE. Remove the polystyrene rack blocks. Position the appliance in the chosen installation position. The sides and rear of the appliance can lie against kitchen units or walls. If the dishwasher is installed next to a heat source, separate it with a heat insulating panel in order to prevent overheating and malfunctions.
EN INSTALLATION INSTRUCTION • If the appliance is not in a niche and can therefore be accessed on one side, cover the door hinge area for safety reasons (cutting hazard). Covers are available as accessories from specialized retailers or from the Technical Service Centre. • To build in the dishwasher, purchase the relative kit from specialized retailers or from the Technical Service Centre. 5.1 Leveling 5.1.2 Levelling the appliance Level the appliance using the relative adjustable feet (e.g.: ref. A fig.
EN INSTALLATION INSTRUCTION Fig. 5-02 5.2 Connections Install the dishwasher so as to allow ease of access to the electrical and hydraulic connections through the adjacent unit. These connections must never be behind the dishwasher. The inlet and drain hoses can be pointed in all directions. make sure that they are not bent, crushed or too tight. Tighten the ring nut after pointing the hoses in the required direction.
EN INSTALLATION INSTRUCTION A through hole with a diameter of at least 8 cm (5/32”) is required to pass the hoses and power cord (ref. A fig. 5-04). Make sure there area no rough edges that could damage the power cord or hoses. If the dishwasher is installed in a metal unit protect the edge of the through hole for the hoses and power cord with a gasket. Do not use extension cords when making the electrical connection as these do not guarantee safety.
EN INSTALLATION INSTRUCTION 5.2.1.1 Connecting to the water tap Connect the inlet hose to a threaded ¾” gas cold water tap, fitting the supplied filter (ref. A fig. 5-05). Firmly secure the hose by tightening the relative ring nut with your hands (ref. B fig. 5-05); finish by tightening another ¼ turn using a pair of plumbing pliers. For models fitted with ACQUASTOP (ref. C fig. 5-05) the filter is already present in the threaded ring nut.
EN INSTALLATION INSTRUCTION Do not cut the inlet hose (see fig. 5-06). If the hose is cut, the dishwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses. Fig. 5-06 When connecting the dishwasher drain hose to the sink make sure that the hose is not bent (ref. A fig.
EN INSTALLATION INSTRUCTION 5.2.1.2 Connecting the drain hose Connecting to a drain Insert the relative hose into a drain with a minimum diameter of 4 cm (1-37/64”) (ref. A fig. 5-08); alternatively, place the hose on the sink (ref. B fig. 5-08) using the supplied hose support (see fig. 5-9), but taking care to avoid obstructions or excessive curving. Make sure the hose cannot fall out. For this purpose, the hose support is fitted with a hole (ref. A fig.
EN INSTALLATION INSTRUCTION Connecting to a “T” union of the drain circuit MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A fig. 5-10) to the “T” union (ref. B fig. 5-10) of the drain circuit using a 38 to 50 mm (1-1/2 to 2”) screw clamp* (ref. C fig. 5-10); if necessary, cut the end of the dishwasher drain hose (ref. D fig.
EN INSTALLATION INSTRUCTION Connecting to a waste disposal unit with an air gap MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit (ref. A fig. 5-11). 2. Connect the dishwasher drain hose (ref. B fig. 5-11) to the air gap (ref. C fig. 5-11) using the wide spring clamp (ref. D fig. 5-11); if necessary, cut the end of the dishwasher drain hose (ref. E fig.
EN INSTALLATION INSTRUCTION Connecting to the air gap (no waste disposal unit) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Connect the dishwasher drain hose (ref. A fig. 5-12) to the air gap (ref. B fig. 5-12) using the wide spring clamp (ref. C fig. 5-12); if necessary, cut the end of the dishwasher drain hose (ref. D fig. 5-12) (do not cut the corrugated section).
EN INSTALLATION INSTRUCTION Connecting to a waste disposal unit (no air gap) MAKE THE CONNECTION UPLINE FROM THE SIPHON OF THE DRAIN LINE AND AT LEAST 400 mm (15-3/4”) ABOVE THE FLOOR ON WHICH THE DISHWASHER WILL BE INSTALLED. 1. Remove the cover of the waste disposal unit (ref. A fig. 5-13). 2. Connect the dishwasher drain hose (ref. B fig. 5-13) to the waste disposal unit inlet (ref. C fig. 5-13), using the wide spring clamp (ref. D fig. 5-13). A D C B Fig.
EN INSTALLATION INSTRUCTION 5.2.2 Electrical connections and warnings CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR. IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE. THIS APPLIANCE MUST BE GROUNDED.
EN INSTALLATION INSTRUCTION IF THE PLUG IS NOT SUITABLE FOR THE SOCKET, CALL IN A QUALIFIED ELECTRICIAN TO FIT A SUITABLE PLUG. The plug at the end of the power cord and the corresponding socket must be of the same type and must conform to current regulations governing electrical appliances. The plug must be accessible after installation. Never remove the plug by pulling on the wire. If the power cord is damaged, have it replaced by the manufacturer or an authorized service centre.
EN INSTALLATION INSTRUCTION Fig. 5-15 Fig. 5-16 Push the dishwasher into position, taking care not to twist or crush the power cord or hoses (see fig. 5-17). TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO PUSH THE DISHWASHER INTO PLACE. Fig.
EN INSTALLATION INSTRUCTION 5.3.2 5.3.2 Procedure for mounting the door panel P rocread edufor re fSTX or m ounting the door panel (not models) Mount the door panel. Mount thetemplate door panel. Place the on the inner surface of the panel, centering it along the upPlace theand template on the inner surface of the panel, centering it along the poupper side matching up the reference locators (ref. A fig. 5-18); mark the per side and matching up the reference locators (ref. A fi g.
EN INSTALLATION INSTRUCTION Drill holes for the panel handle using a drill with a suitable bit. Use the screwdriver to secure the door handle before hooking the panel to the dishwasher (see fig. 5-20). N.B.: the screws are not supplied. Fig. 5-20 Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip in to place (see fig. 5-21). 1 2 Fig.
EN INSTALLATION INSTRUCTION Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm (25/32”) (see fig. 5-22). Fig. 5-22 Make sure the dishwasher door, complete with panel, opens comfortably and that the base plate (ref. A fig. 5-23) does not prevent it from opening fully. If the base plate prevents the door from opening, mark out the section to remove (see fig. 5-23), take out the base plate and cut it along the marking using a compass saw (see fig. 5-24).
EN INSTALLATION INSTRUCTION Fig. 5-24 5.3.3 Completion of installation Finish the cut with a file (see fig. 5-25) in order to remove any burrs and/or imperfections. Put back the base plate (see fig. 5-26) and try to open the dishwasher door fully; if the base plate still obstructs the door, repeat the above operations. Fig. 5-25 Fig.
EN INSTALLATION INSTRUCTION Before securing the dishwasher to the adjacent units, attach the gaskets to the sides. Remove the adhesive band on the gasket (see fig. 5-27). Fig. 5-27 Fix the gasket to the dishwasher, inserting it in the seat on the sides towards the front (see fig. 5-28), and making sure that the long side of the gasket, the one with the hole for inserting the screw, is attached to the outside of the dishwasher; the hole in the long side must match the hole in the dishwasher (see ref. A fig.
EN INSTALLATION INSTRUCTION Fig. 5-29 Fig. 5-30 shows the state of the dishwasher after the above operations are performed. Fig. 5-30 Tighten the supplied screws with a screwdriver; this operation definitively fixes the dishwasher to the adjacent units; cover the side holes using the supplied plugs (ref. A fig. 5-31).
EN INSTALLATION INSTRUCTION Fig. 5-31 5.4 Testing After installation, test the dishwasher by starting a work cycle. Check for leaks and make sure the appliance does not malfunction.
EN 32