Installation Guide

sgn i nr aw dna sno i t cennoc l ac i r t ce l E 2 . 2 . 5

EHT FO YCNEUQERF EHT DNA EGA T LOV EHT T AHT KCEHC
MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE AP-
PLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR.


IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE
IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED
TECHNICAL SERVICE CENTRE.
THIS APPLIANCE MUST BE GROUNDED. IN CASE OF A MAL-
FUNCTION OF FAULT, THE GROUND REDUCES THE RISK OF
ELECTROCUTION BY PROVIDING THE ELECTRICAL CURRENT
WITH AN ALTERNATIVE, LESS RESISTANT PATH.
THIS APPLIANCE MUST BE GROUNDED. IN CASE OF A MAL-
FUNCTION OF FAULT, THE GROUND REDUCES THE RISK OF
ELECTROCUTION BY PROVIDING THE ELECTRICAL CURRENT
WITH AN ALTERNATIVE, LESS RESISTANT PATH. THIS APPLI-
ANCE IS FITTED WITH A SUPPLY CORD CONTAINING A GROUND
WIRE AND PLUG. FIT THE PLUG INTO A SUITABLE SOCKET, IN-
STALLED AND GROUNDED IN COMPLIANCE WITH THE LAWS IN
FORCE IN THE COUNTRY OF INSTALLATION.


BEFORE MAKING ELECTRICAL CONNECTIONS, DISCON-
NECT THE MAINS POWER SUPPLY FROM THE WORK AREA.
sno i t cu r t sn i gn i dnuo rG
otni gu lp eht t i F .gu lp dna er iw dnuorg ht iw droc a ht iw det t fi s i ecna i l ppa s i hT
a suitable socket, installed and grounded in compliance with the laws in force
in the country of installation.

- L A T SN I FO ECA L P EHT N I Y L PPUS SN I AM EHT T AHT KCEHC
LATION COMPLIES WITH THE REGULATIONS IN FORCE IN THE
COUNTRY OF USE, AND THAT IT IS CORRECTLY GROUNDED.

WARNING AN INCORRECTLY CONNECTED GROUND WIRE MAY
GENERATE THE RISK OF ELECTROCUTION. IF IN DOUBT AS TO
THE CORRECT GROUNDING OF THE APPLIANCE, CALL IN A
QUALIFIED ELECTRICIAN OR THE TECHNICAL ASSISTANCE
SERVICE. DO NOT CHANGE THE PLUG ATTACHED TO THE
APPLIANCE.
IF THE PLUG IS NOT SUITABLE FOR THE SOCKET, CALL IN A
QUALIFIED ELECTRICIAN TO FIT A SUITABLE PLUG.
The plug at the end of the power cord and the corresponding socket must be
of the same type and must conform to current regulations governing electrical
appliances. The plug must be accessible after installation. Never remove the
plug by pulling on the wire. If the power cord is damaged, have it replaced
.er tnec eci vres dez i rohtua na ro rerutcafunam eht yb
DO NOT USE EXTENSION CORDS, ADAPTORS OR SHUNT CON-
NECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVER-
HEATING OR BURNING, WITH CONSEQUENT FIRE HAZARD.



T I E V AH , DROC Y LPPUS EHT OT EGAMAD FO TNEV E EHT N I
RE-
PLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNI-
CAL SERVICE CENTRE IN ORDER TO AVOID ANY RISK.

gninoissimmoC 3.5
5.3.1 Installation procedure
. g fi ees ( r ood r ehsawhs i d eh t r evo gn i y l po t k r ow eh t f o h t aen r ednu eh t nae l C
5-14) and apply the steam guard, as shown in fi g. 5-15 (see fi g. 5-15 if the
adhesive guard is applied; see fi g. 5-16 if the steel guard is applied). This guard
protects the worktop from steam and condensation when the door of the dish-
washer is opened at the end of the washing cycle.
Fig. 5-14
EN
23
INSTALLATION INSTRUCTION