Operation Manual

20
Setting water hardness
1. Press (B2) to enter the menu;
2. Press (B10) or (B8) until the display (B) displays
WATER HARDNESS ;
3. To change the level selected, press the symbol itself until
the required level is displayed (Level 1 = soft water;
Level4=very hard water);
Press to go back to the homepage.
The machine is now reprogrammed with the new water hard-
ness setting.
WATER SOFTENER FILTER
Some models are tted with a water softener lter (C4): if your
model is not equipped with one, we recommend buying one
through an authorised customer service centre.
To use the lter correctly, follow the instructions below.
Installing the lter
1. Remove the lter (C4) from the packaging;
2. Press (B2) to enter the menu;
3. Press (B10) or (B8) until the display shows
WATER FILTER ;
4. Press ;
5. TURN THE DATE INDICATOR UNTIL THE NEXT 2 MONTHS ARE
DISPLAYED (g.43):
turn the date indicator disk until the next two months of
use are displayed. Press ;
Please note:
the lter lasts about two months if the appliance is used normal-
ly, if the coee machine is left unused with the lter installed, it
will last a maximum of 3 weeks.
1. FILL FILTER WITH WATER UNTIL IT’S COMPLETELY FILLED
(g.44): To activate the lter, run tap water through the
hole in the lter as shown in the gure until water comes
out of the openings at the side for more than a minute.
Press ;
2. Extract the tank (A12) from the appliance and ll with
water.
3. IMMERSE FILTER IN THE WATER TANK LETTING AIR BUBBLES
ESCAPE (g.45): Insert the lter in the water tank and im-
merse it completely for about ten seconds, sloping it and
pressing it lightly to enable the air bubbles to escape. Press
;
4. INSERT FILTER INTO ITS HOUSING AND PUSH IT DOWN TO
BOTTOM: Insert the lter in the lter housing (g.42) and
press as far as it will go. Press ;
5. INSERT WATER TANK : Close the tank with the lid (A15), then
replace the tank in the machine.
6. PLACE 0.5L CONTAINER UNDER OUTLET, PRESS OK TO FILL
FILTER (g.8): place the container under the hot water/
steam spout (C6) and press : delivery starts and
stops itself automatically.
The symbol appears on the display alongside the time to
indicate that the lter has been enabled. The coee machine can
now be used.
Replacing the lter
Replace the lter (C4) when the display (B) shows the message
REPLACE WATER FILTER, PRESS OK TO START : to replace
immediately, press and follow the instructions from
point 4.
To postpone replacing the lter to another time, press :
on the display the symbol is a reminder that the lter
needs to be replaced.
To replace, proceed as follows:
1. Extract the water tank (A12) and exhausted lter;
2. Remove the new lter from the packaging;
3. Press (B2) to enter the menu;
4. Press (B10) or (B8) until the display shows
WATER FILTER ;
5. Press ;
6. The display shows REPLACE FILTER ;
7. Press ;
8. Follow the operations described in the previous paragraph
from point 5.
The lter is now active and the coee machine can be used.
Please note:
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the lter even if
the message has not yet been displayed.
Removing the lter
If you want to use the appliance without the lter (C4), you must
remove it and notify the appliance of its removal. Proceed as
follows:
1. Extract the water tank (A12) and exhausted lter;
2. Press (B2) to enter the menu;
3. Press (B10) or (B8) until the display shows
WATER FILTER ;
4. Press ;