5713237501_00_0318 SMEG S.p.A. Via Leonardo Da Vinci, 442016 Guastalla (RE) Italia www.smeg.
INSTRUCTIONS MODE D’EMPLOI MANUAL DE INSTRUCCIONES CMSU6451 X CMSCU451 S COFFEE AND CAPPUCCINO MAKER MACHINE À CAFÉ ET À CAPPUCCINO CAFETERA PARA CAFÉ Y CAPUCHINO
ELECTRIC CHARACTERISTICS CARACTERISTIQUES ELECTRIQUES CARACTERISTICAS ELECTRICAS: 120V - 60Hz 1350W 2
A6 A7 A A3 A4 A8 A9 A5 A15 A2 A10 A11 A1 A12 A16 A13 A14 A17 A18 A21 A19 A20 B B1 B6 B3 B8 B7 B5 B4 B2 C C1 C6 C2 C3 C4 C5 C7 C8 C9 C10 3 C11
2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 4
1 2 17 18 19 20 21 22 23 24 25 26 27 29 30 31 5 28
CONTENTS Changing coffee temperature.................................................19 Changing the length of time the appliance remains on ..........19 Setting water hardness ..........................................................19 Resetting default values (reset) .............................................19 Washing procedure.................................................................19 INTRODUCTION.........................................................
IMPORTANT SAFEGUARDS INTRODUCTION Thank you for choosing the automatic coffee and cappuccino maker. We hope you enjoy using your new appliance. Take a few minutes to read these instructions. This will avoid all risks and damage to the machine. When using electrical appliances, basic safety precautions should always be followed including the following: Symbols used in these instructions • READ ALL INSTRUCTIONS Important warnings are identified by these symbols.
• • • • • • • • • • • • • system of the house checked by a qualified electrician. The manufacturer can not be held responsible for damages caused by the lack, or inadequacy, of an effective grounding system. Do not use an extension cord to connect the appliance to electricity. Extension cord doesn’t guar- antee the required safety of the appliance (danger of overheating).
A5. Infuser A6. Lights A7. Control panel A8. Hot water and steam nozzle A9. Water tank A10. Coffee spout (adjustable height) A11. Drip tray A12. Bean container lid A13. Container for coffee beans A14. Grinding adjustment knob A15. Pre-ground coffee funnel door A16. Compartment for measure A17. Pre-ground coffee funnel A18. Power cable A19. Main switch A20. Tray A21. IEC connector C10. C11.
light up the spout and cup tray. The lights stay on until the appliance is turned off. While coffee, steam or hot water is being delivered, the cooling fan comes on. At the end of the function, the cooling fan remains on to avoid condensation forming inside the cabinet. After several minutes, the fan goes off automatically. m mm m 455 455 in in 9191 17. 17. m 22 m m in .87 220m in 0.87 N.B.: The appliance also completes this cycle if switched off by turning the knob (C6) to the right or left.
xx 16 2 x 16 x 2 x 16 x 16 x 4 x 2 x 4 x 2 Position the rails on the sides of the cabinet as shown in the figure. Fix with the screws, then extract them completely. If the coffee maker is installed over a warmer drawer (500 W max.), use the top surface of this as a reference to position the x 1 rails. x 1 In this case, there will be no surface to rest the rails on. Position the appliance on the rails, making sure the pins are correctly inserted in the housings, then fix it with the screws supplied.
USING THE APPLIANCE FOR THE FIRST TIME right or left. • Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which cannot be interrupted. The appliance is ready for use only after completion of this cycle. • 1. 2. 3. 4. 5. 6. Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be new.
Take care to avoid scalds). NOTE 1: If the coffee is delivered a drop at a time or not at all, turn the grinding adjustment knob (fig. 12) one click clockwise (see “Adjusting the coffee mill”). Proceed one click at a time until coffee delivery is satisfactory. NOTE 2: If the coffee is delivered too fast and the cream is not satisfactory, turn the grinding adjustment knob (fig. 12) one click anticlockwise (see “Adjusting the coffee mill”).
ADJUSTING THE COFFEE MILL enable the coffee mill. NOTE 1: Never introduce pre-ground coffee when the machine is off or it could spread through the inside of the appliance. NOTE 2: Never add more than 1 level measure, otherwise either the appliance will not make the coffee and the pre-ground coffee will be dispersed inside the appliance, dirtying it, or the coffee will be delivered a drop at a time. NOTE 3: Use the measure provided to add the right amount of coffee.
• • • • Remove the lid of the milk container. Fill the container with about 100 grams / 0.22 lb of milk for each cappuccino to be prepared (fig. 19). Never exceed the MAX level (corresponding to about 750 ml / 25.36 oz) marked on the jug. You should ideally use skimmed or semi-skimmed milk at refrigerator temperature (about 5°C / 41°F). Make sure the intake tube is correctly inserted in the rubber washer (fig. 20) then replace the milk container lid.
CLEANING AND MAINTENANCE To remove the tray: 1. Open the service door (A2) (fig. 14). 2. Remove the drip tray (A11) and the grounds container (A4) (fig. 15). 3. Empty the drip tray and grounds container and wash them. 4. Replace the drip tray complete with grounds container. 5. Close the service door. Before performing any cleaning operations, leave the machine to cool down completely and unplug from the mains power supply. Never immerse the coffee maker in water. It is an electrical appliance.
Cleaning the milk container 2. Open the service door (A2) (fig. 14). 3. Remove the drip tray (A11) and grounds container (fig. 15). 4. Press the two red release buttons inwards and at the same time pull the infuser outwards (fig. 28). Important! Always clean the tubes inside the milk container (B) when you prepare milk. If there is still milk in the container, do not leave it out of the refrigerator for longer than strictly necessary.
• • • • • DESCALE NO TEMPERATURE MEDIUM OFF AFTER 1 HOUR WATER HARDNESS 4 DEFAULT VALUES NO relating to the procedure to follow in the event of contact with the skin and eyes. N:B:: Use the descaler recommended by the manufacturer only. Use of other descalers invalidates the guarantee. Failure to descale the appliance as described also invalidates the guarantee.
• Press the OK button (C5) and refill the water tank with clean water. • The descale programme is now terminated and the appliance is ready to make coffee again. NOTE: If descaling is interrupted before completion, the machine still displays the descaling message and the process must be begun again from the beginning. Empty the water tank, rinse with clean water and deliver a cup of hot water. • • • Important! FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE GUARANTEE.
N.B.: If the appliance is not used for an extended period, place the main switch (A19) on the back of the appliance in the 0 position. TECHNICAL SPECIFICATION Voltage: 120 V~ 60 Hz max. Absorbed power: 1350W Pressure: 15 bars Water tank capacity: 47.43 fl. oz / 1.4 liters Size LxHxD: 23.43 x 17.91 x 16.22 in / 595 x 455 x 412 mm Max beans container capacity: 8.82 oz / 250 g Weight of machine: 57.32 lb / 26 kg Water / Steam spout: 2 oz / 5 g Milk container: 28.2 oz / 800 g Power cable length: 74.8 in / 1.
DISPLAYED MESSAGES DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY FILL TANK The water tank is empty or positioned Fill the tank with water and/or insert it incorrectly. correctly, pushing it as far as it will go. GROUND TOO FINE ADJUST MILL Insert water spout and press OK (C5) The grinding is too fine and the coffee is delivered too slowly. The machine cannot make coffee as there is air in the hydraulic circuit.
TROUBLESHOOTING If the problem cannot be resolved as described, contact Customer Services. Below is a list of some of the possible malfunctions. PROBLEM POSSIBLE CAUSE The coffee is not hot. The cups were not preheated. The coffee is not creamy enough . The coffee is ground too coarsely. REMEDY Heat the cups by rinsing them in hot water or leaving them to rest for at least 20 minutes on the cup warmer tray.
PROBLEM POSSIBLE CAUSE REMEDY The milk contains bubbles or squirts out The milk is not cold enough or is not You should ideally use skimmed or semiof the milk spout. semi-skimmed. skimmed milk at refrigerator temperature (about 5°C / 41°F). If the result is still disappointing, try another brand of milk. The frothed milk regulator is incorrectly Move the frothed milk regulator slightly adjusted. towards the word “CAFFELATTE” (see section “Making cappuccino”). The milk container lid is dirty.
