EN User Manual Dishwasher DI4522
CONTENTS Safety information Safety instructions Product description Control panel Programme selection Programmes overview Basic settings 2 4 6 6 7 8 9 Before first use Daily use Hints and tips Care and cleaning Troubleshooting Technical information 13 14 16 18 21 25 CUSTOMER CARE AND SERVICE Always use original spare parts. When contacting our Authorised Service Centre, ensure that you have the following data available: Model, Serial Number. The information can be found on the rating plate.
• • • • • • Children between 3 and 8 years of age and persons with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised. Children of less than 3 years of age should be kept away from the appliance unless continuously supervised. Do not let children play with the appliance. Keep detergents away from children. Keep children and pets away from the appliance when the door is open.
• The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. SAFETY INSTRUCTIONS Installation WARNING! Only a qualified person must install this appliance. • Remove all the packaging. • Do not install or use a damaged appliance. • Do not use the appliance before installing it in the built-in structure due to safety manner. • Follow the installation instructions supplied with the appliance.
Use • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. • Dishwasher detergents are dangerous. Follow the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete. Some detergent may remain on the dishes. • Do not store items or apply pressure on the open door of the appliance.
PRODUCT DESCRIPTION The graphics below is just a general product overview. For more detailed information, refer to other chapters and/or documents provided with the appliance.
5 Option button 6 programme button Indicators Indicator Description Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to "Before first use". Salt indicator. It is on when the salt container needs refilling. Refer to "Before first use". Self Clean indicator. It is on when the appliance needs internal cleaning with the Self Clean programme. Refer to "Care and cleaning". Drying phase indicator. It is on when a programme with the drying phase is selected.
PROGRAMMES OVERVIEW Pro‐ gramme Self Clean Type of load Degree of soil Programme phases Options • • Crockery Cutlery • Fresh • • • • Wash 50 °C Intermediate rinse Final rinse 45 °C Dry Assist • All types of loads • All de‐ grees of soil • Prewash • • • • Crockery Cutlery Pots Pans • • Normal Lightly dried-on • • • • • Wash 60 °C Intermediate rinse Final rinse 55 °C Drying Dry Assist • • • • Crockery Cutlery Pots Pans • • Normal Lightly dried-on • • • • • • Prewash Wash 50 °C
Programme 1) 2) Self Clean Water (l) Energy (kWh) Duration (min) 8.5 - 10.4 0.743 - 0.909 90 9.9 0.704 240 8.0 - 10.5 0.683 - 1.047 120 - 170 7.4 - 8.9 0.396 - 0.484 60 1) The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of dishes and the degree of soil can change the values. 2) The values for programmes other than ECO are indicative only.
4 How to change a setting 5 Make sure the appliance is in setting mode. 1. Press Previous or Next until the indicator dedicated to the desired setting flashes. 1 3 2 Setting mode How to enter setting mode You can enter setting mode before starting a programme. You cannot enter setting mode while the programme is running. To enter setting mode, press and hold and simultaneously seconds. for about 3 • The light related to and the indicator flash. • The indicators , and are on.
The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results. Water hardness German de‐ grees (°dH) French de‐ grees (°fH) mmol/l Clarke de‐ grees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.
a programme). Regeneration initiation has no impact on the cycle duration, unless it occurs in the middle of a programme or at the end of a programme with a short drying phase. In that cases, the regeneration prolongs the total duration of a programme by additional 5 minutes. Subsequently, the rinsing of the water softener that lasts 5 minutes may begin in the same cycle or at the beginning of the next programme.
CAUTION! If children have access to the appliance, we advise to deactivate Dry Assist. The automatic opening of the door may pose a danger. Key tones The buttons on the control panel make a click sound when you press them. You can deactivate this sound. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap.
How to fill the rinse aid dispenser B C A CAUTION! Only use rinse aid designed specifically for dishwashers. 1. Press the release element (A) to open the lid (B). 2. Pour the rinse aid in the dispenser (C) until the liquid reaches the marking "FILL". 3. Remove the spilled rinse aid with an absorbent cloth to prevent excessive foam formation. 4. Close the lid. Make sure that the lid locks into position. CAUTION! The compartment (C) is for rinse aid only. Do not fill it with detergent. DAILY USE 1.
The light related to the button flashes. 2. Activate if desired. 3. Close the appliance door to start the programme. How to select and start the programme , press and hold for 3 1. To select seconds. The light related to the button flashes. 2. Close the appliance door to start the programme. How to activate 1. Select a programme. . 2. Press The light related to the button is on. is not a permanent option and must be activated every time before you start a programme.
If the door is opened for more than 30 seconds during the drying phase, the running programme ends. It does not happen if the door is opened by Dry Assist function. The Auto Off function This function saves energy by switching the appliance off when it is not operating. • When the programme is completed. • After 5 minutes if a programme was not started. End of the programme When the programme is complete, the Auto Off function switches the appliance off automatically.
• Always use the correct quantity of detergent. Insufficient dosage of detergent can result in poor cleaning results and hard-water filming or spotting on the items. Using too much detergent with soft or softened water results in detergent residues on the dishes. Adjust the amount of detergent based on the water hardness. Refer to the instructions on the detergent packaging. • Always use the correct quantity of rinse aid. Insufficient dosage of rinse aid decreases the drying results.
CARE AND CLEANING WARNING! Before any maintenance other than running the programme Self Clean, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spray arms negatively affect the washing results. Check these elements regularly and, if necessary, clean them. Self Clean Self Clean is a programme designed to clean the appliance interior with optimal results. It removes limescale and grease buildup. When the appliance senses the need for is on.
C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks.
CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. Cleaning the lower spray arm We recommend to clean the lower spray arm regularly to prevent soil from clogging the holes. Cleaning the upper spray arms We recommend to clean the upper spray arms regularly to prevent soil from clogging the holes. Clogged holes can cause unsatisfactory washing results. The upper spray arms are placed under the upper basket.
and fix it in the duct by turning it counterclockwise. Make sure that the mounting element locks into place. 4. To install the spray arm back, insert the mounting element in the spray arm TROUBLESHOOTING WARNING! Improper repair of the appliance may pose a danger to the safety of the user. Any repairs must be performed by qualified personnel. The majority of problems that may occur can be solved without the need to contact an Authorised Service Centre.
Problem and alarm code Possible cause and solution The appliance does not drain the water. • The lights related to the programme buttons flash 2 times intermittently. • An acoustic signal sounds intermittently. • • • Make sure that the sink spigot is not clogged. Make sure that the interior filter system is not clogged. Make sure that the drain hose has no kinks or bends. The anti-flood device is on. • The lights related to the programme buttons flash 3 times intermittently.
Problem and alarm code Possible cause and solution The level of water inside the appliance is too high. • The lights related to the programme buttons flash 15 times intermittently. • An acoustic signal sounds intermittently. • • • Switch the appliance off and on. Make sure that the filters are clean. Make sure that the outlet hose is installed at the right height above the floor. Refer to the installation instruc‐ tions. The appliance stops and starts more times during op‐ eration.
The dishwashing and drying results are not satisfactory Problem Possible cause and solution Poor washing results. • • • • Poor drying results. • • • • • • There are whitish streaks or bluish layers on glasses and dishes. • • Refer to "Daily use", "Hints and tips" and the basket loading leaflet. Use more intensive washing programme. option to improve the washing results of Activate the a selected programme. Clean spray arm jets and filter. Refer to "Care and Cleaning".
Problem Possible cause and solution Odours inside the appliance. • • Refer to "Internal cleaning". Start the Self Clean programme with a descaler or a cleaning product designed for dishwashers. Limescale deposits on the ta‐ bleware, on the tub and on the inside of the door. • • • • The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard. Refer to "The water softener".
Link to the EU EPREL database EPREL database using the link https:// eprel.ec.europa.eu and the model name and product number that you can find on the rating plate of the appliance. Refer to the chapter "Product description". The QR code on the energy label supplied with the appliance provides a web link to the registration of this appliance in the EU EPREL database. Keep the energy label for reference together with the user manual and all other documents provided with this appliance.
