Contents 1.1 1.2 1.3 1.4 1.5 1.6 1.7 General safety instructions Identification plate Manufacturer liability Appliance purpose This user manual How to read the user manual To save energy 2 Description 2.1 2.2 2.3 2.4 2.5 General Description Cooktop Control panel Other parts Available accessories 3 Use 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Cleaning the appliance Removing the door Cleaning the door glazing Removing the internal glass panes Pyrolytic cycle Extraordinary maintenance 5 Installation 5.1 5.2 5.3 5.
Instructions 1 Instructions 1.1 General safety instructions Risk of personal injury • During use the appliance becomes hot. Care should be taken to avoid touching heating elements inside the oven. • Protect your hands by wearing oven gloves when handling food inside the oven cavity. • Never try to put out a fire or flames with water: turn off the appliance and smother the flames with a fire blanket or other appropriate cover.
their housings with their respective burner caps. • Be aware of how rapidly the cooking zones heat up. Do not place empty pans on the heat. Danger of overheating. • Fats and oils can catch fire if they overheat. Do not leave the appliance unattended while preparing foods containing oils or fats. If fats or oils catch fire, never put water on them. Place the lid on the pan and turn off the relevant cooking zone. • The cooking process must always be monitored.
Instructions • If the power supply cable is damaged, contact technical support immediately and they will replace it. Risk of damaging the appliance • Do not use abrasive or corrosive detergents (e.g. scouring powders, stain removers and metallic sponges) on glass parts. • Use wooden or plastic utensils. • Racks and trays must be inserted as far as they will go into the side guides. The mechanical safety locks that prevent them from being removed must face downwards and towards the back of the oven cavity.
Instructions move the appliance. • NOT SUITABLE WITH AFTERMARKET LIDS OR COVERS. EN • If any liquid does boil over or spill, remove the excess from the cooktop. • Take care not to spill acidic substances such as lemon juice or vinegar onto the cooktop. • Do not put empty pans or frying pans on switched on cooking zones. • Do not use steam jets to clean the appliance. • Do not use rough or abrasive materials or sharp metal scrapers.
Instructions check that the tightening torque of gas connections is between 10 Nm and 15 Nm. • At the end of the installation, check for any leaks with a soapy solution, never with a flame. • Have the electrical connection performed by authorised persons. • The appliance must be connected to earth in compliance with electrical system safety standards.
• Place the supplied data plate to a suitable adjacent surface or within the instruction manual for future reference. 1.3 Manufacturer liability The manufacturer declines all liability for damage to persons or property caused by: • use of the appliance other than the one envisaged; • non-observance of the user manual provisions; • tampering with any part of the appliance; • use of non-original spare parts. 1.4 Appliance purpose • This appliance is intended for cooking food in the home environment.
Instructions 1.7 To save energy • Only preheat the appliance if the recipe requires you to do so. • Unless otherwise indicated on the package, defrost frozen foods before placing them in the oven. • When cooking several types of food it is recommended to cook the foods one after the other to make the best use of the already hot oven. • Use dark metal moulds: They help to absorb the heat better. • Remove all trays and racks which are not required during cooking.
Description EN 2 Description 2.
Description 2.2 Cooktop AUX = Auxiliary burner SR = Semi-rapid burner R = Rapid burner UR = Ultra rapid burner 2.3 Control panel 1 Temperature knob 3 Programmer clock This knob allows you to select the cooking temperature. Turn the knob clockwise to the required value, between the minimum and maximum setting. Useful for displaying the current time, setting programmed cooking operations and programming the minute minder timer.
Description The oven's various functions are suitable for different cooking modes. After selecting the required function, set the cooking temperature using the temperature knob. time even after the appliance has been turned off. EN 5 Function knob 6 Cooktop burner knobs Useful for lighting and adjusting the cooktop burners. Press and turn the knobs anticlockwise to the value to light the relative burners. Turn the knobs to the zone between the maximum and minimum setting to adjust the flame.
Description Rack Deep tray Useful for supporting containers with food during cooking. Useful for collecting fat from foods placed on the rack above. Tray rack To be placed over the top of the oven tray; for cooking foods which may drip. Tray Useful for collecting fat from foods placed on the rack above. 14 The accessories intended to come into contact with food are made of materials that comply with the provisions of current legislation.
Use Instructions High temperature inside the oven during use Danger of burns • Keep the oven door closed during cooking. • Protect your hands wearing heat resistant gloves when moving food inside the oven. • Do not touch the heating elements inside the oven. • Do not pour water directly onto very hot trays. • Do not allow children younger than 8 years old to come near the appliance when in operation.
Use High temperature inside the oven during use Danger of fire or explosion • Do not spray any spray products near the oven. • Do not use or leave flammable materials near the oven or the storage compartment. • Do not use plastic kitchenware or containers when cooking food. • Do not put sealed tins or containers in the oven. • Do not leave the oven unattended during cooking operations where fats or oils could be released. • Remove all trays and racks which are not required during cooking.
3.2 Using the accessories Ring reducers Racks and trays The ring reducers have to be placed on the cooktop grids. Make sure they are placed properly. Racks and trays have to be inserted into the side guides until they come to a complete stop. • The mechanical safety locks that prevent the rack from being taken out accidentally have to face downwards and towards the oven back. Gently insert racks and trays into the oven until they come to a stop.
Use 3.3 Using the cooktop All the appliance's control and monitoring devices are located together on the front panel. The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electronic ignition device. Simply press the knob and turn it anticlockwise to the maximum flame symbol, until the burner lights. If the burner does not light in the first 15 seconds, turn the knob to and wait 60 seconds before trying again.
3.4 Using the storage compartment The storage compartment is at the bottom of the cooker. To open it, pull the handle towards you. It can be used to store cookware or metallic objects necessary when using the appliance. 3.5 Using the oven Switching on the oven To switch on the oven: 1. Select the cooking function using the function knob. 2. Select the temperature using the temperature knob.
Use Grill The heat coming from the grill element gives perfect grilling results above all for thin and medium thickness meat and, in combination with the rotisserie (where fitted), gives the food an even browning at the end of cooking. Perfect for sausages, spare ribs and bacon. This function enables large quantities of food, particularly meat, to be grilled evenly. Fan grill The air produced by the fan softens the strong heatwave generated by the grill, grilling perfectly even very thick foods.
3.6 Cooking advice General advice • Use a fan assisted function to achieve consistent cooking at several levels. • It is not possible to shorten cooking times by increasing the temperature (the food could be overcooked on the outside and undercooked on the inside). Advice for cooking meat • Cooking times vary according to the thickness and quality of the food and to consumer taste. • Use a meat thermometer when roasting meat, or simply press on the roast with a spoon.
Use Advice for defrosting and proving • Place frozen foods without their packaging in a lidless container on the first shelf of the oven. • Avoid overlapping the food. • To defrost meat, use the rack placed on the second level and a tray on the first level. In this way, the liquid from the defrosting food drains away from the food. • The most delicate parts can be covered with aluminium foil. • For successful proving, a container of water should be placed in the bottom of the oven. 3.
Use Timed cooking is the function which allows a cooking operation to be started and then ended after a specific length of time set by the user. 1. Keep the clock key symbol pressed until the appears. 2. Press the clock key display the symbol again. On the and the text appear, alternating with the current time. 3. Use the value increase and value decrease keys to set the required minutes of cooking. 4. Select a function and a cooking temperature. 5. Wait approx.
Use 4. Use the or key to set the required minutes. (for example 1 hour) 5. Press the menu key . The text will appear on the display in sequence with the pre-set cooking duration added to the current time (for example, the cooking end time shown is 18:30). 6. Press the or key to set the cooking end time. (for example, 19:30). Bear in mind that a few minutes for oven preheating must be added to the cooking time. 7. Wait approx. 7 seconds without pressing any key in order for the function to activate.
Use The minute minder timer does not stop the cooking operation but rather informs the user when the set time has run out. The minute minder timer can be activated at any time. 1. Keep the clock key pressed for per a few seconds. The display shows the figures and the symbol flashing between the hours and minutes. 2. Use the value increase and value decrease keys to set the number of minutes required. 3. Wait approx. 5 seconds without pressing any key to finish setting the minute minder.
Use Cooking information table Lasagne Pasta bake 3-4 3-4 Convection Convection Runner position from the bottom 1 1 Roast veal Pork Sausages Roast beef Roast rabbit Turkey breast Roast pork neck Roast chicken 2 2 1.5 1 1.5 3 2-3 1.
Cleaning and maintenance Instructions Improper use Risk of damage to surfaces • Do not use steam jets to clean the appliance. • Do not use cleaning products containing chlorine, ammonia or bleach on steel parts or parts with metallic finishes on the surface (e.g. anodizing, nickel- or chromium-plating). • Do not use abrasive or corrosive detergents (e.g. scouring powders, stain removers and metallic sponges) on glass parts. • Do not use rough or abrasive materials or sharp metal scrapers.
Cleaning and maintenance Cleaning the igniters and thermocouples 4.2 Removing the door • If necessary, clean the igniters and thermocouples with a damp cloth. • If there is any dry residue, remove it with a toothpick or needle. For easier cleaning, the door can be removed and placed on a tea towel. To remove the door proceed as follows: 1. Open the door completely and insert two pins into the holes on the hinges indicated in the figure.
3. To reassemble the door, put the hinges in the relevant slots in the oven, making sure that grooved sections A are resting completely in the slots. Lower the door and once it is in place remove the pins from the holes in the hinges. 4.4 Removing the internal glass panes For easier cleaning the door internal glass panes can be disassembled. 1. Remove the internal glass pane by pulling the rear part gently upwards, following the movement indicated by the arrows (1). 2.
Cleaning and maintenance 4. Clean the external glass pane and the panes previously removed. Use absorbent kitchen roll. In case of stubborn dirt, wash with a damp sponge and neutral detergent. 5. Refit the panes in the reverse order in which they were removed. 6. Reposition the internal glass pane. Take care to centre and insert the 4 pins into their housings in the oven door by applying slight pressure.
Manually disengaging the door lock lever 1. Move the door lock lever to the right until it stops. Improper use Danger of burns • The following must always be carried out when the appliance is cold and switched off. • Never attempt to disengage the door lock lever manually during the pyrolytic cycle. The door lock lever is located in the first slot on the left under the control panel, in the upper part of the front of the oven. (as seen from above) 2. Release the door lock lever gently.
Cleaning and maintenance 4.5 Pyrolytic cycle Pyrolytic is an automatic hightemperature cleaning procedure which causes dirt to dissolve. This process makes it possible to clean the inside of the oven very easily. Improper use Risk of damage to surfaces • Remove any large amounts of food residues or spills from previous cooking operations from the inside of the oven. Preliminary operations Before starting the pyrolytic cycle: • Clean the internal glass pane following the usual cleaning instructions.
6. At the end of the pyrolytic cycle, all the numbers will flash and a buzzer will sound to indicate the end of the automatic cleaning cycle. 7. Return the function knob to the "0" position. 8. The door remains locked as long as the temperature inside the oven returns to safety levels. 9. Wait for the oven to cool down and collect the residues deposited inside with a damp microfibre cloth.
Cleaning and maintenance 4.6 Extraordinary maintenance 4. Slide out and remove the light bulb. Replacing the oven light bulb Live parts Danger of electrocution • Unplug the appliance. The oven is fitted with two 40W light bulbs. 1. Completely remove all accessories from inside the oven. 2. Remove the racks/trays support frames. 3. Remove the bulb cover using a tool (e.g. a screwdriver). Do not touch the halogen light bulb directly with your fingers, but wrap it in insulating material. 5.
Cleaning and maintenance EN What to do if... The appliance does not work. • The circuit breaker is faulty: look in the fuse box and check that the circuit breaker is in working order. • Power cut: check whether the kitchen light works. The gas burner does not ignite. • Power cut or damp ignition plugs: light the gas burner with a gas lighter or a match. The oven does not heat up. • Faulty fuse: check and, if required, replace the circuit breaker. • The function knob has not been set: set the function knob.
Installation 5 Installation 5.1 Minimum clearance to combustible surfaces Freestanding cooker A 600 mm (Overhead) measured from the highest part of the highest burner and 750 mm for an exhaust fan. B 200 mm (Vertical combustible surface) measured form the edge of the nearest burner. C 10 mm (Horizontal combustible surface) below the hob. Refer to AS/NZS 5601 (Protection of a combustible surface) if the above minimum clearances cannot be achieved.
This appliance is suitable for connection with rigid pipe or flexible hose. The isolating manual shut-off valve connection point must be accessible when the appliance is installed. Flexible hose assembly must be certified to AS/NZS 1869 class B or D, be of appropriate internal diameter for the total gas consumption (10mm), be kept as short as possible (not exceeding 1200mm), must not be in contact with the floor or any hot surface or sharp surface.
Installation Room ventilation The room containing the appliance should have a permanent air supply in accordance with the standards in force. The room where the appliance is installed must have enough air flow needed for the regular combustion of gas and the necessary air change in the room itself. The cooktop shall be installed in rooms with natural ventilation, as required by Standards regulations AS/NZS5601.
5.3 Adaptation to different types of gas In case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas cocks. Turn the knob rapidly from the maximum to the minimum setting: the flame should not go out. Repeat the operation on all gas cocks. Replacing nozzles 1. Remove the pan stands, burner caps and flame-spreader crowns to access the burner casings. 2.
Installation Burner and nozzle characteristics table 1 ULPG 2.75 kPa AUX SR R UR Nominal gas consumption (MJ/h) Injector (1/100 mm) 4.0 54 7.0 68 11.0 88 15.0 105 2 NG 1.0 kPA AUX SR R UR Nominal gas consumption (MJ/h) Injector (1/100 mm) 4.0 90 7.0 120 12.0 155 13.0 165 Overall dimensions Location of gas and electrical connection points. 5.4 Positioning Heavy appliance Danger of crush injuries • Place the appliance into the piece of furniture with the aid of a second person.
Installation EN General information This appliance may be installed next to walls, one of which must be higher than the worktop, at a minimum distance of 50 mm from the side of the appliance, as shown in figures A and C relative to the installation classes. Any wall units positioned above the worktop must be at a minimum distance of at least 600 mm. If a hood is installed above the cooktop, refer to the hood instruction manual to ensure the correct clearance is left.
Installation Positioning and levelling Heavy appliance Risk of damage to the appliance • Insert the front feet first and then the rear ones. Fastening to the wall The anti-tip devices must be installed in order to prevent the appliance tipping over. 1. Screw the wall fastening plate to the rear of the appliance. • After making the gas and electrical connections, screw on the four feet supplied with the appliance. The appliance must sit level on the floor to ensure stability.
3. Assemble the fastening bracket. 4. Align the base of the hook on the fastening bracket with the base of the slot on the wall fastening plate. 5. Align the base of the fastening bracket with the ground and tighten the screws to fix the measurements. 6. Use 50 mm for the distance from the side of the appliance to the bracket holes.
Installation 7. Move the bracket onto the wall and mark the position of the holes to be drilled in the wall. Wall fixing 8. After drilling the holes in the wall, use wall plugs and screws to fasten the bracket to the wall. 9. Push the cooker towards the wall, and at the same time, insert the bracket in the plate fastened to the rear of the appliance. 2. Attach the chain to the cooker with the screw just removed. 1. Turn the screw placed behind the cooktop near the gas connection. 3.
4. Mark the wall in the position where the hole is to be drilled. Assembling the upstand The upstand provided is an integral part of the product. It must be fastened to the appliance prior to installation. The upstand must always be positioned and secured correctly on the appliance. 1. Loosen the two bolts on the back of the cooktop using a screwdriver. 5. Drill the hole and insert a wall plug. 6. Attach the chain and push the appliance to the wall. 2. Place the upstand on the worktop.
Installation 3. Clip the tongues of the upstand to the ventilation slot of the cooktop. (A) Assembling the toe skirt 4. Secure the upstand to the cooktop by tightening the 2 screws previously loosened. 2. Align the toe skirt with the corresponding holes on the appliance. 3. Fasten the toe skirt using the screws that were previously removed. 46 The toe skirt must always be positioned and secured correctly on the appliance. 1. Use a screwdriver to remove the highlighted screws.
Installation Power voltage Danger of electrocution • Have the electrical connection performed by authorised persons. • Use personal protective equipment. • The appliance must be connected to earth in compliance with electrical system safety standards. • Disconnect the mains supply. • Do not pull the cable to remove the plug. • Use cables withstanding a temperature of at least 90°C. • The tightening torque of the screws of the terminal board conductors must be 1.5 - 2 Nm.
Installation The aforementioned power cables are sized taking into account the coincidence factor (in compliance with standard EN 60335-2-6). 3. Install the power supply cable. 5.6 Access to the terminal board Access via the plate To connect the power supply cable, access to the terminal board on the rear cover: 1. Remove the screws securing the lid to the rear cover. Loosen the cable fastener screw before installing the power supply cable. 4.
Access via the rear casing To connect the power cable, remove the fastening screws on the rear casing as shown in the figure. Fixed connection Fit the power line with an all-pole circuit breaker with a contact separation distance sufficient to provide complete disconnection in category III overvoltage conditions, pursuant to installation regulations. The disconnection incorporated in the fixed wiring must be compliant to AS/NZS 3000 regulations. 5.
