Libretto di Istruzioni Instructions Manual Manuel d’Instructions Bedienungsanleitung Gebruiksaanwijzing Manual de instrucciones Manual de Instruções ɋɮɥɩɝɩɟɬɭɝɩ ɪɩ ɸɥɬɪɦɮɛɭɛɱɣɣ Bruksanvisning KR37X
INDICE IT CONSIGLI E SUGGERIMENTI ..............................................................................................................................................4 CARATTERISTICHE ..............................................................................................................................................................5 INSTALLAZIONE...............................................................................................................................................
ÍNDICE PT CONSELHOS E SUGESTÕES ............................................................................................................................................58 CARACTERÍSTICAS ............................................................................................................................................................59 INSTALAÇÃO .....................................................................................................................................................
RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
CHARACTERISTICS 540 Dimensions Min. Min. 550mm 550mm Components Ref. 1 3 7 8 8c 9 Ref. 11 12a 12b 12e 13 EN Q.ty 1 1 1 1 1 1 Q.ty 4 4 4 2 4 Q.
INSTALLATION Wall drilling and bracket fixing 100 100 12a 1240 11 100 100 1050 390 175 170 When installing the hood in recycling version it has to be taken into consideration that space remaining between the hood and the upper limit (ceiling or self) is at least 8-10 cm. On the wall, draw: • a Vertical line up to the ceiling or upper limit, at the centre of the area in which the hood is to be fitted; • a Horizontal line at a minimum of 1050 mm above the Cooker Top; .
Hood support mounting • Lean the hood support 3 against the wall making sure that holes in the hood support correspond to those in the wall. • Block the hood support to the wall using 4 12a (5 x 70) screws supplied with the hood. • Before fastening the screws definitively make sure that the support is well-levelled. Only after this operation proceed with the definitive tightening of the screws.
ø 150 RECIRCULATION VERSION AIR OUTLET • Insert pvc pipe 7 provided onto the Hood Canopy Outlet. . 7 Hood body mounting Ducting version • In case the air outlet connection on the upper part of the hood has been chosen it will be necessary to remove the pre-cut piece. • Lean the hood body on the support and fix it laterally with the 4 12b screws. • Cover the screw seats with the plugs 13 supplied with the hood. Recycling version • Remove the pre-cut piece.
ELECTRICAL CONNECTION • Connect the hood to the mains through a twopole switch having a contact gap of at least 3 mm. • Open the lighting unit by pulling on the notch. • Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. • Being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. • Connect the control connector Cmd.
USE L T1 L1 T2 L2 T3 L3 T4 L4 Control panel Button Function Led L Press briefly to turn the lighting system on and off. Press and hold for approx. 2 seconds to turn the lighting system on and off at reduced intensity. T1 Turn the suction motor on and off at speed one. If the filter saturation alarm is on, this resets it. On. T2 Turn the suction motor on at speed two. If the filter saturation alarm is on, this resets it. On. T3 On.
MAINTENANCE Metal grease filters These can also be washed in the dishwasher, and need to be cleaned when all the command LEDs light up in a continuous manner or at least once every 2 months use, or more frequently if use is particularly intensive. Resetting the alarm signal • Press any of the buttons except the Light button. Cleaning the Filters • Open the lighting unit by pulling on the nocth.
Activated Charcoal Filter (Recirculation Version) • This cannot be washed or regenerated, and must be changed when all the command LEDs start to flash, or at least once every 4 months. Activating the alarm signal • In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date.
