INSTRUCTION MANUAL MANUEL D’INSTRUCTIONS KD90-KD120-KD150-KT90-KT110--
WARNING! READ AND SAVE THESE INSTRUCTIONS. Read the instructions carefully before installing and/or using the hood. Before connecting, make sure that the mains voltage corresponds to the voltage on the rating plate inside the hood. (see fig. 7) Once you remove the appliance from its packaging make sure it is intact. If the product is damaged, do not use it and contact the Smeg assistance network. It is recommended that a qualified technician performs installation and adjustment operations .
GROUNDING INSTRUCTIONS: This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. WARNING – Improper grounding can result in a risk of electric shock.
INSTALLATION INSTRUCTIONS: The hood is supplied with all the necessary accessories for installation. The minimum distance between the cooker and the lower part of the hood must be 750 mm for gas cookers and 650 mm for electric cookers (Fig.1). The hood is supplied with a motor intake (Fig 2).
Recirculation mode: Leave the motor intake free. Install the active carbon filters as shown in page 7. Warning: if the hood is not supplied with an active carbon filter, it is necessary to buy it separately and assemble it before using the hood. m) Chimney assembly: Adjust the two telescopic chimneys to the required length (fig. 6). Block the chimneys by tightening the two H screws . Place the chimneys group on the top side of the hood carefully. Put the chimney bracket K on the B chimney (fig. 6).
OPERATING INSTRUCTIONS: CONTROL PANEL: In order to achieve the best performance, it is recommended to start the hood a few minutes before starting cooking and keep it on for at least 15 minutes after finishing cooking or after all fumes and odours have disappeared. To start the hood, identify your type of control panel and follow the instructions: SLIDER: - Key (A) to turn on/off the hood’s light.
OPTIONAL FUNCTIONS: - AUTO POWER-OFF TIMER: Pushing one of the speed adjustment buttons (2-3-4) twice, you will activate the “Auto power-off timer” function that turns the motor and light off after 10 mins. The activation of such function is signalled by the blinking LED above the pressed button. - FILTERS CLEANING WARNING: When all the 4 LEDs blink at the same time (which is programmed to happen every 100h of operation), the user is required to clean/replace the filters .
METAL FILTERS CLEANING: Special attention should be reserved to the metal grease filters. An excess of grease in the filter, as well as affecting the performance of the hood, can also be a fire risk. To avert fires, the filters must be cleaned regularly at least once a month or more frequently, in the case of a heavy use of the appliance. According to your hood’s model, remove one filter at a time as shown in these pictures. Wash the filters thoroughly with a non-bleach detergent, either by hand or machine.
Before performing any cleaning and/or maintenance operation, disconnect the hood from the mains supply. According to the model, the hood can be equipped with different kind of lighting such as incandescent, halogen and neon lamps. a) Incandescent lamps: E14 – 40W 230V lamps. To replace them, remove the transparent fixture from the control panel, unscrew the lamp and screw in the new one. b) Halogen lamps: G4, 20W - 12V lamps . To replace the lamp, use a screwdriver to remove the glass-supporting ring.
WARRANTY AND TECHNICAL ASSISTANCE SERVICE The hood packaging includes, together with this operating and maintenance booklet, the Smeg Warranty Booklet. Please read the Smeg Warranty Booklet for complete information about the warranty (N.B. bulbs and filters are not covered by your warranty). In the case of failure, please call Customer Service 0870 9909907 and provide the following data: The model indicated inside the hood (fig.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste.
Cod.
