Model: LB30AFNF FB30AFNF Frigorifero/congelatore da incasso Manuale di installazione Built-in Fridge/Freezer Installation Manual
20 Contents 1. Note before installing .............................................................. 21 2. Components to install .............................................................. 22 3. Assembly/Disassembly diagram of Built-in refrigerator ............ 23 4. Dimension of Built-in refrigerator and furniture ....................... 24 5. Installing the built-in refrigerator ............................................. 25 6. Procedure to install 1) Preparing before installing the refrigerator ...
21 1. Note before installing Caution ■ Install the product at the place avoiding the heat from the heater or the boiler or the direct sunlight, with the shade and the good ventilation always. ■ Prepare the furniture possible to circulate air by referring to the size. Install the product for air to smoothly flow via the front intake hole. If not, it may cause to prevent the normal performance of the product.
22 2. Components to install ① Top cover of refrigerator ② Hinge holder ③ Depth adjusting bracket ④ Depth adjusting bracket (diameter = 5.
23 3.
24 4. Dimension of Built-in refrigerator and furniture 400m m or longe r ※ The entire furniture thickness shown at this figure is based on 15mm. m 50m ※ The furniture dimension should comply with the figure. 600m m r nge or lo mm 0 8 5 595m m 5 Inne 70mm r dim ens ion 1775 mm 1830mm or longer 1688.5 mm 1800mm or longer Inner dimension 39mm 554 mm m 0m /56 545 400m m or longe r mm 50 50mm 400 mm Caution When the furniture thickness is changed, the door size of the furniture is changed.
25 5. Installing the built-in refrigerator ■ The minimum space for ventilating should be prepared for the smooth heat exchange of the refrigerator. 1. It should be structured for air to enter from the intake hole and to exit from the discharge hole. 2 Ceiling min. 50mm 1 2. The passage ¡ should be secured when the passage ¨ is not secured. 3. 200cm2 or more of the air ventilation at ¨ and ¡ should be secured. min.
26 6. Procedure to install 1) Preparing before installing the refrigerator 1. Installing the top cover of the refrigerator 1) Fold the top cover of the refrigerator ¨ in advance as shown at the figure. 45mm 45mm 1 2) Fix the top cover of the refrigerator ¨ at the place by 45mm from the end of the furniture with the wood screws ⓑ (three spots). (If the thickness of the furniture is 18mm or 20mm, cut and install the top cover of the refrigerator ¨ as described at the following “Reference“.
27 6. Procedure to install 1) Preparing before installing the refrigerator 2. Insert the hinge base ② into the hinges (two spots). (See Figure 1) (If the thickness of the furniture is 20mm, do not install the hinge base ②.) 3. Tilt backward the refrigerator and loosely fix the height adjusting bracket ③ at the bottom (two spots) of the refrigerator door by using the hinge screws ⓔ as shown at the figure. (Figure 1) 2 2 3 e e 3 2) Case related work after placing the refrigerator 4.
28 6. Procedure to install 2) Case related work after placing the refrigerator 6. Adjust the horizontal/vertical level of the refrigerator by turning the level adjusting leg( 1⃞ When the top side is deep The refrigerator is tilted backward, so turn counterclockwise the level adjusting leg to adjust the level. 1⃞ 2⃞ When the bottom side is deep The refrigerator is tilted forward, so turn clockwise the level adjusting leg to adjust the level.
29 6. Procedure to install 2) Case related work after placing the refrigerator 7. Make sure that the end of the hinge base ② is aligned with the front right of the furniture. Furniture Hinge base② Hinge Front side of the furniture 8. Fix the top hinge and the bottom hinge by the hinge screws ⓕ (four spots). (See Figure 3) When fixing the screws, be careful of being damaged by the hinge operation. (Figure 3) f 9.
30 6. Procedure to install 2) Case related work after placing the refrigerator 10. Open the refrigerator door, place the hinge bracket ⑤ at the top left of the refrigerator, and fix them at the furniture and the refrigerator respectively with the wood screw ⓑ (one spot) and the bracket screws ⓔ (two spots). (See Figure 5) 11. Insert the hinge bracket cover ⑥ from the left and then press it. (See Figure 6).
31 6. Procedure to install 3) Furniture door related work 12. Place the paper jig ⑦ on the reference line of the paper jig at the rear side of the furniture door. (See Figure 7) ※ Reference - Place the reference line of the paper jig at 1595mm from the floor of the furniture. - If the furniture door is long, place the reference line of the paper jig at 1595mm plus ‘A’ from the floor of the furniture.
32 6. Procedure to install 4) Refrigerator door related work 15. Insert the height adjusting nuts ⓓ (two spots at the bottom) into the height adjusting screw, and then place the top bracket ⑧ of the furniture door at the height adjusting screw of the top of the refrigerator door. Use the height adjusting nut to adjust the height of the furniture door and set the level.
33 6. Procedure to install 4) Refrigerator door related work 17. Loosely fix the top bracket ⑧ with the height adjusting nuts ⓓ (Figure 13), and adjust the depth gap between the furniture door and the front of the furniture to 4mm. At this time, adjust the location of the furniture door for the furniture door not to touch the furniture when opening/closing the door. d 8 (Figure 13) 18. Use the spanner ⓖ to check the dimension.
34 6. Procedure to install 4) Refrigerator door related work 21. Move the furniture door to the depth direction to adjust the depth gap to 4mm (See Figure 14), and fix the depth adjusting bracket ⑨ to both sides (two spots) of the refrigerator door with the door screw ⓐ. (Figure 16) (Figure 16) 9 a 22.
35 6. Procedure to install 5) Installation checkup and finishing work 24. Insert the font cover ⑭ of the hinge into the front of the inside. (two spots) 25. Insert the ventilation cover ⑮ into the rectangular floorcloth pan. 26. Attach the gasket ⒃ as shown at the figure. Attach it to the opposite side from the hinge side. If the gasket is long, cut it according to the length to use. 1800mm 27. Insert the cap screw ⑬ as shown at the figure.
36 6. Procedure to install 6) Changing the opening direction of the refrigerator door ※ Before installing, change the door to work. 1. Loosen the screws ❶ and ❸ at the hinge of the case section, and push the door to the right to disconnect. (See Figure 20) 1 2 2. Completely loosen the screws ❶ and ❸, and then fix them at the opposite side loosely. (See Figure 20) 3. Loosen the screws ❷ and ❹ fixed to the door to disconnect the hinge. (Figure 20) 4.
37 6. Procedure to install 7) Furniture door gap ※ When installing two pieces of furniture closely, keep the gap between them 5mm or more.
FRIGORIFERO Istruzioni per l'uso Nel ringraziarvi per avere acquistato questo prodotto SMEG, vi raccomandiamo di leggere attentamente le seguenti istruzioni e di conservare questo manuale per eventuali consultazioni future. FRIDGE User's Guide Please read this User's Guide carefully before operating and keep it handy for reference at all times. KÜHLSCHRANK Bedienungsanleitung Lesen Sie diese Bedienungsanleitung vor dem Betrieb sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf.
Table of Contents Introduction Operation Registration 32 Important Safety Instruction 32 Identification of Parts 46 Temperature Control 47 Display Panel For Temperature Control 47 Power / 48 How to adjust the temperature in the refrigerator compartment / 48 Extra Cooling / 49 Self Test / 49 Door Alarm / 49 Suggestion On Food storage Care and Maintenance Trouble Shooting Low-temperature catalyst deodorization system (removing the odor) 50 How to store food properly 50 Storing Food 51 Ge
Introduction Registration The model and serial number are found on the rear of this unit. This number is unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Staple your receipt here. Introduction Date of Purchase : Dealer Purchased From : Dealer Address : Dealer Phone No. : Model No. : Serial No.
Introduction Important Safety Instruction WARNING To reduce the risk of fire, electric shock, or injury to persons when using your product, basic safety precautions should be followed, including the following. Read all instructions before using this appliance. 1. When connecting the power The dedicated outlet should be used. • Using several devices at one outlet may cause fire. • The electric leakage breaker may damage food and the dispenser may be leaked.
Introduction Important Safety Instruction Do not extend or modify the length of the power plug. It causes electric shock or fire by the electric damage of the power cord or others. Unplug the power plug when cleaning, handling or replacing the interior lamp of the fridge-freezer. • It may cause electric shock or injury. • When replacing the interior lamp of the fridge-freezer, make sure that the rubber ring for preventing the electric spark within the socket is not taken off.
Introduction Important Safety Instruction Make sure of grounding. Consult a qualified electrician or service person if the grounding instructions are not completely understood, or if you have doubts on whether the appliance is properly grounded. The incorrect grounding may cause breakdown and electric shock. Be sure to use grounded exclusive proper voltage consent for the power plug. It becomes the cause of fire.
Introduction Important Safety Instruction Prevent children from entering the product. It may endanger the life of a child if the child enters the refrigerator. Opening and closing the door of the refrigerator vigorously may cause the stored food in the refrigerator basket to fall by shock and hurt the foot, so take precautions. Do not install the fridge-freezer in the wet place or the place which water or rain splashes. Deterioration of insulation of electric parts may cause electric leakage.
Introduction Important Safety Instruction Do not store the medicine or the academic materials at the fridge-freezer. When the material with the strict temperature control is stored, it may be deteriorated or it may make an unexpected reaction to cause any risk. Do not use the combustible spray near the fridgefreezer. It may cause fire. Avoid the heating devices. Install in places away from the fire such as the place where flammable gas is leaked. It may cause fire.
Introduction Important Safety Instruction Use the submerged fridge-freezer after checking it. It may cause electric shock or fire. When gas is leaked, do not touch the fridge-freezer or the outlet and ventilate the room immediately. • The explosion by spark may cause fire or burn. • Because this fridge-freezer uses natural gas (isobutene, R600a) as the environment-friendly refrigerant, even a small amount (80~90g) is combustible.
Introduction Important Safety Instruction Do not allow any person except the qualified engineer to disassemble, repair or alter the fridgefreezer. It may cause injury, electric shock or fire. Do not use the fridge-freezer for non-domestic purpose (storing medicine or testing material, using at the ship, etc.). It may cause an unexpected risk such as fire, electric shock, deterioration of stored material or chemical reaction. When disposing the fridge-freezer, remove the packing materials from the door.
Introduction Important Safety Instruction Install the fridge-freezer on the solid and level floor. Installing it on the unstable place may cause death by falling down the fridge-freezer when opening or closing the door. Do not insert the hands or the metal stick into the exit of cool air, the cover, the bottom of the fridgefreezer, the heatproof grill (exhaust hole) at the backside. It may cause electric shock or injury. CAUTION Violating this direction may cause injury or damage house or furniture.
Introduction Important Safety Instruction Do not put bottle in the freezer. It may freeze the contents to break the bottle to cause injury. Do not insert the hands into the bottom of the fridge-freezer. The iron plate of the bottom may cause injury. Carry the fridge-freezer with the handle bar at the bottom of the front and the top of the rear. Otherwise, your hands may be slipped to cause injury. Because the product is heavy, carrying it alone may hurt people or accidents may occur.
Introduction Important Safety Instruction Warning Precaution 42 • This fridge-freezer must be properly installed and located in accordance with the Installation Instruction before it is used. • Before you install this fridge-freezer reference to installation manual. • Never unplug your fridge-freezer by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
Introduction Important Safety Instruction Do not modify or extend the Power Cord length • Do not disassemble, repair or alter the appliance. It may cause fire or abnormal operations, which may lead to injury. • Pull the power plug out of the socket before replacing the interior light in the refrigerator. Otherwise, there is a risk of electric shock.
Introduction Important Safety Instruction Warning Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. Do not damage the refrigerant circuit. Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
Introduction Important Safety Instruction Caution 45 • If the wall socket is loose, do not insert the power plug. It may cause electric shock or fire. • Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull it straight out from the outlet. You may disconnect a wire and cause a short circuit. • Do not use a wet or damp cloth when cleaning the plug. Remove any foreign matter from the power plug pins. Otherwise, there is a risk of fire.
Introduction Identification of Parts Dairy Corner Lamp Door Basket Removable Glass Shelf Bottle Shelf Egg Tray Snack Corner Bottle Guide Multi-Air Flow Duct 2 Bottle Door Basket Lamp Vegetable Drawer Used to keep fruits and vegetables crisp.
Operation Temperature Control Your fridge has controls that let you regulate the temperature in the fridge compartments.
Operation Power • If you push button more than 3 seconds you can switch on or off the Refrigerator. POWER 3SECS How to adjust the temperature in the refrigerator compartment • The initial Temperature of the Refrigerator Compartment is 0°C and 6°C respectively. You can now adjust the temperature of the compartments as you want. • REFRIGERATOR Note When you press the temperature control button, the temperature of the Refrigerator part is change by 1 degree.
Operation Please select this function for prompt cooling. • This function is used when you want to cool the foods quickly. Press the EXTRA COOL (Extra Cooling) button once, and then the quick cool operation starts with the lamp it. • The Extra Cooling operation takes about 2 hours. When its operation ends, it automatically returns to the previous temperature setting.
Suggestions on food storage Low-temperature catalyst deodorization system (removing the odor) 1. It does not harm the stored food with the excellent function to remove the odor. 2. In particular it is efficient to remove the odor of the fermented food. - Insert the strongly smelt food into the sealed container to store. It may cause to soak other food with a scent. Features How to store food properly Place dishes or food properly spaced.
Suggestions on food storage Storing Food Caution Note • Do not store food which goes bad easily at low temperature, such as banana, and melon. • Allow hot food to cool prior to storing. Placing hot food in the fridge could spoil other food, and lead to higher electric bills. • When storing the food, use a container with a lid. This prevents moisture from evaporating, and helps food to keep its taste and nutrients. • Do not block air vents with food.
Care and Maintenance General Information 1~2 hour power failure does no harm to the foods stores. Try to avoid opening and closing the door too frequently. Power Failure • If You Move • Anti Condensation Pipe • The Anti-Condensation pipe is installed around the front side of fridge as well as on the partition between fridge compartment to prevent dewing. • Especially after installation or when ambient temperature is high, the fridge may feel hot, which is quite normal.
Care and Maintenance How to disassemble each component It can be possible to disassemble only when the door is opened by 90° or wider. Disassembling should be done by the reverse order of assembling. Disconnect the power plug or turn off the main power before disassembling. Indoor lamp - Insert the fingers into the inside slot of the top cover and pull out it to remove. - Push the upper part of the middle cover and pull out it to remove. - Turn counterclockwise the indoor lamp to disassemble.
Care and Maintenance Slightly pull out and then slightly lift up and pull out the front side of the shelf to remove. Refrigerator/ Bottle shelf 2 2 1 1 Snack compartment Pull out and then slightly lift up and pull out it to remove. Vegetable compartment Pull out and then slightly lift up and pull out the vegetable compartment to remove as shown at the figure. After removing the vegetable compartment, slightly lift up and pull out the front side of the vegetable compartment cover to remove.
Care and Maintenance - Insert the ‘-’ screwdriver into the top of the deodorant cover and pull out the cover to remove. - After removing the cover, pull out the deodorant to remove. - The deodorant may be reused by drying the deodorant with the hair dryer or bathing it in the sun to remove the soaked smell. Deodorant Note Do not insert the screwdriver into the cool air opening.
Care and Maintenance Cleaning Be sure to unplug the power or shutdown the main switch in your house. Before Cleaning Clean the outside of the fridge with a soft cloth soaked with hot water or liquid detergent. If you use a detergent, be sure to wipe it with a clean wet cloth. Exterior As above. Interior After Cleaning Check that the power cord is not damaged, power plug has not overheated, and that the power plug is tightly inserted into the outlet.
Trouble Shooting Before calling for service, check this list. It may save you both time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Possible Causes Problem Power plug may be unplugged from the electric outlet. Plug it in securely. • House fuse has blown or circuit breaker has tripped. Check and/or replace fuse and reset circuit breaker. • Power cut. Check house lights.
Trouble Shooting Problem Possible Causes Moisture collects inside • Fridge has odor • Door not closing properly • Interior light does not work • • Too frequent or too long door openings. In humid weather, air carries moisture into fridge when doors are opened. Foods with strong odors should be tightly covered or wrapped. • Check for spoiled food. • Interior needs cleaning. Refer to CLEANING section. Food package is keeping door open. Move packages that keep door from closing.
SMEG IN THE WORLD Headquarters Smeg S.p.A. Via Leonardo da Vinci, 4 42016 Guastalla (RE) Tel. +39 0522 8211 Fax Italia. +39 0522 821452 Fax Export. +39 0522 821455 E-mail. commerciale.incasso@smeg.it www.smeg.it Russia SMEG RUSSIA Russia, 121108, Moscow Minskaia str., 1G- f.18 Zolotye Kliuch ll Tel. +7 495 645 9651 Fax. +7 495 645 9661 E-mail. smeg-russia@smeg.com www.smeg.ru Subsidiaries Spain SMEG ESPANA, S.A. c/Hidráulica, 4 - P.I. La Ferreria 08110 Montcada i Reixac (Barcelona) Tel.
