Contents 1.1 1.2 1.3 1.4 1.5 1.6 1.7 General safety instructions Manufacturer liability Appliance purpose Disposal Identification plate This user manual How to read the user manual 2 Description 2.1 General Description 2.2 Symbols 2.3 Available accessories 3 Use 26 26 27 27 27 28 28 28 29 29 30 30 31 3.1 Instructions 3.2 First use 3.3 Using the hob 31 31 32 4 Cleaning and maintenance 34 4.1 Instructions 4.2 Cleaning the appliance 34 34 5 Installation 5.1 5.2 5.3 5.4 5.5 5.6 5.
Instructions 1 Instructions 1.1 General safety instructions Risk of personal injury • During use the appliance and its accessible parts become very hot. • Never touch the heating elements during use. • Keep children under eight years of age at a safe distance if they are not constantly supervised. • Children must never play with the appliance. • Never rest metallic objects such as knives, forks, spoons and lids on the appliance during use. • Switch the appliance off immediately after use.
Instructions The manufacturer declines all liability for damage to persons or property caused by: • use of the appliance other than the one envisaged, • non-observance of the user manual provisions, • tampering with any part of the appliance, • use of non-original spare parts. 1.3 Appliance purpose This appliance is intended for cooking food in the home environment. Every other use is considered improper.
Instructions 1.5 Identification plate 1.7 How to read the user manual The identification plate bears the technical data, serial number and brand name of the appliance. Do not remove the identification plate for any reason. This user manual uses the following reading conventions: 1.6 This user manual This user manual is an integral part of the appliance and must therefore be kept in its entirety and in an accessible place for the whole working life of the appliance.
Description 2 Description EN 2.
Description 2.2 Symbols 2.3 Available accessories Cooking zones Burner wrench (for installer only) Front left Rear left Central Rear right Front right Centre left Burner knobs For removing and replacing the hob burners. Useful for lighting and adjusting the hob burners. Press and turn the knobs anticlockwise to the value to light the relative burners. Turn the knobs to the zone between the maximum and minimum setting to adjust the flame. Return the knobs to the position to turn off the burners.
Use 3 Use Improper use Danger of burns • Make sure that the flame-spreader crowns are correctly positioned in their housings with their respective burner caps. • Oils and fat could catch fire if overheated. Be very careful. • Do not leave the appliance unattended during cooking operations where fats or oils could be released. • Do not spray any spray products near the appliance. • Do not touch the appliance's heating elements when it is running. Leave them to cool before cleaning.
Use 3.3 Using the hob All the appliance's control and monitoring devices are located together on the front panel. The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electronic ignition device. Simply press the knob and turn it anticlockwise to the maximum flame symbol, until the burner lights. If the burner does not light in the first 15 seconds, turn the knob to and wait 60 seconds before trying again.
Practical tips for using the hob Using a griddle For better burner efficiency and to minimise gas consumption, use pans with lids and of suitable size for the burner, so that flames do not reach up the sides of the pan. Once the contents come to the boil, turn down the flame far enough to ensure that the liquid does not boil over. A few precautions are necessary if you wish to use a griddle: • The griddle can be pre-heated with the burner on maximum power for no more than 10 minutes.
Cleaning and maintenance 4 Cleaning and maintenance 4.1 Instructions Improper use Risk of damage to surfaces • Do not use steam jets for cleaning the appliance. • Do not use cleaning products containing chlorine, ammonia or bleach on steel parts or parts with metallic finishes on the surface (e.g. anodizing, nickel- or chromium-plating). • In case of contact with overly harsh detergents, hard water or spills (cooking water, sauce, coffee etc.), clean the hob as soon as it has cooled.
Cooking hob grids Igniters and thermocouples Remove the grids and clean them with lukewarm water and non-abrasive detergent. Make sure to remove any encrustations. Dry them thoroughly and return them to the hob. For correct operation the igniters and thermocouples must always be perfectly clean. Check them frequently and clean them with a damp cloth if necessary. Remove any dry residues with a wooden toothpick or a needle.
Installation 5 Installation 5.1 Safety instructions Heat production during appliance operation Risk of fire • Check that the piece of furniture material is heat resistant. • Check that the piece of furniture has the required slots. Veneers, adhesives or plastic coatings on adjacent furniture should be temperatureresistant (>90°C), otherwise they might warp over time.
Installation L (mm) X (mm) Y (mm) 600 - 720 555 - 560 478 - 482 If there are other pieces of furniture (lateral walls, drawers, etc.), dishwashers or fridges under the hob, a double-layer wooden base must be installed at least 10 mm from the bottom of the hob to avoid any accidental contact. It must only be possible to remove the double-layer base using suitable equipment. 5.
Installation Hob seal To prevent leakage of liquid between the frame of the hob and the work surface, place the adhesive seal provided along the entire outer edge of the hob before assembly. Do not use silicone to secure the hob. This would make it impossible to remove the hob, if necessary, without damaging it. 5.4 Fixing brackets Screw the fixing brackets (A) into the holes on the sides of the bottom casing to properly fasten the hob to the structure. 5.
Installation Connection with a flexible steel hose with conical fitting Make the connection to the gas mains using a continuous wall flexible steel hose whose specifications comply with the applicable standard. Carefully screw the hose connector 3 to the appliance’s gas connector 1 (½” thread ISO 228-1), placing the supplied seal 2 between them. Apply insulating material to the thread of connector 3, then tighten the flexible steel hose 4 to the connector 3.
Installation Extraction of the combustion products The combustion products may be extracted by means of hoods connected to a natural draught chimney whose efficiency is certain or via forced extraction. An efficient extraction system requires precision planning by a specialist qualified in this area and must comply with the positions and distances indicated by the applicable standards. When the job is complete, the installer must issue a certificate of conformity.
Installation Removing the hob top EN 1. Remove the grids from the hob. 4. Unscrew the burner rings using the supplied wrench. 2. Remove the flame-spreader crowns and relative burner caps. 3. Pull the knobs upwards to remove them. 5. Remove the top.
Installation Replacing nozzles Adjusting the minimum setting for natural or city gas Light the burner and turn it to the minimum position. Extract the gas tap knob and turn the adjustment screw next to the tap rod (depending on the model) until the correct minimum flame is achieved. Refit the knob and verify that the burner flame is stable. Turn the knob rapidly from the maximum to the minimum setting: the flame should not go out. Repeat the operation on all gas taps. 1.
Installation Adjusting the minimum setting for LPG EN Tighten the screw located at the side of the tap rod clockwise all the way. Following adjustment to a gas other than the one originally set in the factory, replace the gas setting label fixed to the appliance with the one corresponding to the new gas. The label is inserted inside the nozzle pack (where present). Lubricating the gas taps Over time the gas taps may become difficult to turn and get blocked.
Installation Gas types and Countries No Gas types 1 Natural Gas G20 G20 20 mbar G20/25 20/25 mbar 2 Natural Gas G25 G25 25 mbar 3 Natural Gas G25 G25 20 mbar 4 LPG G30/31 G30/31 28/37 mbar G30/31 30/37 mbar G30/31 30/30 mbar 5 LPG G30/31 G30/31 50 mbar 6 City Gas G110 G110 8 mbar 7 City Gas G120 G120 8 mbar IT • GB-IE FR-BE • AT • • NL ES PT SE RU DK • • • • • • • • • • • • • • • • • It is possible to identify the available gas types based on the country the appliance is to be ins
Installation Burner and nozzle characteristics tables 2 3 4 5 6 7 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Reduced capacity (W) Primary air (mm) Natural Gas G25 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Reduced capacity (W) Primary air (mm) Natural Gas G25 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Reduced capacity (W) Primary air (mm) LPG G30/31 Rated heating capacity (kW) Nozzle diameter (1/100 mm) Reduced capacity (W) Primary air (mm) Rated capacity G30 (g/h)
Installation 5.7 Electrical connection Power voltage Danger of electrocution • Have the electrical connection performed by authorised technical personnel. • Use personal protective equipment. • The appliance must be connected to earth in compliance with electrical system safety standards. • Disconnect the main power supply. • Do not pull the cable to remove the plug. • Use cables withstanding a temperature of at least 90°C. • The tightening torque of the screws of the terminal supply wires must be 1.
