Instructions Manual

ManualsBrandsSmeg ManualsDomestic AppliancesSF112U

Table of Contents

1 Installation 6

1.1 General installation instructions 6

1.2 Electrical requirements 7

1.3 Electrical connection 8

1.4 Cable replacement 10

1.5 Positioning 10

Important Safety Instructions

WARNING: If the instructions contained in this manual are not followed

precisely, fire or explosion may result causing property damage, personal

injury or death.

NOTE: This appliance must be installed solely and exclusively by a qualified

technician. Any technical procedures must be carried out by an authorized

technician.

READ AND SAVE THESE INSTRUCTIONS - Your safety and the safety of

others are very important.

We have provided many important safety messages throughout this manual and

on the appliance.

Read all the instructions before using the appliance and always obey all safety

messages.

RECOGNIZE SAFETY INFORMATION

This is a safety alert symbol. This symbol alerts you to potential hazards that can

result in severe personal injury or death.

UNDERSTAND SIGNAL WORDS

A signal word - DANGER, WARNING or CAUTION - is used with the safety alert

symbol. DANGER denotes the most serious hazards. It means you could be killed

or seriously injured if you do not immediately follow the instructions. WARNING

means you could be killed or seriously injured if the instructions are not followed.

CAUTION indicates a potentially hazardous situation which, if not avoided, could

result in minor to moderate injury.

Summary of content (12 pages)

PAGE 1
Table of Contents 1.1 1.2 1.3 1.4 1.5 6 General installation instructions Electrical requirements Electrical connection Cable replacement Positioning EN 1 Installation 6 7 8 10 10 Important Safety Instructions WARNING: If the instructions contained in this manual are not followed precisely, fire or explosion may result causing property damage, personal injury or death. NOTE: This appliance must be installed solely and exclusively by a qualified technician.
PAGE 2
Important Safety Instructions WARNING • This appliance is intended for home use only. • Use this appliance only for its intended purpose. The manufacturer cannot be held liable for damage caused by improper use of this appliance. • This appliance complies with current safety regulations. Improper use of this appliance can result in personal injury and material damage. • Read all the instructions before installing or using the appliance for the first time.
PAGE 3
Important Safety Instructions CAUTION: This unit is designed as a cooking appliance. For safety purposes, never use it for warming the room or as a space heater. • Do not obstruct oven vents or openings for heat exhaust. • Test the appliance immediately after installation, following the instructions in this booklet. If the appliance does not work properly, disconnect it from the electrical power supply and call the service center. DO NOT attempt to repair the appliance.
PAGE 4
Installation 1 Installation 1.1 General installation instructions • Proper installation is your responsibility. Have a qualified technician install this oven. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with installation guidelines specified on the model/serial ID plate. The model/serial ID can be found on the internal frame of the oven when the door is opened.
PAGE 5
Installation Warning Electrical shock hazard • Have the electrical connection performed by authorized technical personnel. • Frame grounded by connection of grounding lead to neutral lead. If local codes do not permit grounding through neutral, open connection and use grounding lead to ground the unit in accordance with local codes. Connect neutral lead to branch-circuit neutral conductor in usual manner. • Do not use an adaptor. • Do not use an extension cord.
PAGE 6
Installation • Wire size and connections must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 ELECTRICAL CODE (*) – latest edition or CSA Standard C22.1-94, Canadian Electrical code, Part 1 (**) and CSA C22.2 No. O-91 or latest edition and all local codes and ordinances for the kilowatt rating of the appliance. IMPORTANT: Observe all governing codes and ordinances.
PAGE 7
Installation U.S. and Canada installation / 4-wire branch circuit See diagram. Where local codes allow the connection of the ground wire from the oven to the power supply cable neutral wire (white wire): • The ground wire must be connected first; • If local codes permit, connect the green or yellow-green ground wire from the appliance and the white wire from the appliance to the power supply neutral wire (white wire).
PAGE 8
Installation • Connect to a 20A fuse or circuit breaker. Connect to copper wire, or, if connection is made to aluminum house wiring, use UL-listed or CSA-approved connectors approved for joining aluminum and copper wiring. NOTE: Both leads coming out of the appliance must be connected according to the diagrams shown in figures. Fixed connection Fit the power line with an multi-pole circuit breaker in compliance with installation regulations.
PAGE 9
Important instructions Fastening bushings For best results, follow these instructions before and during the oven installation: • Decide on the final location of the oven. Locate the existing wiring to avoid drilling into or severing wiring during installation. • To avoid damage to the floor, place the oven on cardboard prior to installation. Do not lift by the door handle or any part of the frame or trim. • Remove the shipping materials and tape from the oven.
PAGE 10
Installation Appliance overall dimensions (top view) (front view) (side view) 12
PAGE 11
Installation EN Standard installation (side view) Mounting under countertop (front view) (top view) mm Mounting into a column (front view) in Width of cabinet A min. 603 min. 23 3/4 Width of cutout B 554-564 21 13/16 - 22 3/16 Height of cutout C 583-585 22 15/16 - 23 1/16 Top of cutout to bottom of upper cabinet door D 3/ - 7/ 9 - 11 8 16 Top of cutout to top of lower cabinet door E min. 5 min. 3/16 Bottom of cutout to floor (recommended) F 121 - 1105 4 5/8 - 32 Depth of cutout G min. 560 min.
PAGE 12
Installation Flush installation (side view) Mounting under countertop (front view) (top view) mm A B C D F Mounting into a column (front view) Cleats and platform must be recessed 24 mm - 15/16” from the front of the cabinet. G H co jb Flush installation requires a platform (p) underneath the unit body. 14 p sc in Width of flush inset cutout 603 min.