Contents 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 General safety instructions Appliance purpose Manufacturer’s liability This user manual Disposal Identification plate How to read the user manual To save energy 2 Description 2.1 2.2 2.3 2.4 General description Control panel Other parts Available accessories 3 Use 3.1 3.2 3.3 3.4 3.5 56 60 60 60 61 61 62 62 63 63 64 65 65 67 Using the accessories Using the oven Cooking advice Special functions Settings 4 Cleaning and maintenance 4.1 4.2 4.3 4.4 4.5 4.
Instructions 1 Instructions 1.1 General safety instructions RISK OF INJURY • During use the appliance and its accessible parts become very hot. Never touch the heating elements during use. • Protect your hands by wearing oven gloves when moving food inside the oven. • Never try to put out a fire or flames with water: Turn off the appliance and smother the flames with a fire blanket or other appropriate cover.
• If you need to move food or at the end of cooking, open the door 5 cm for a few seconds, let the steam come out, then open it fully. • Do not insert pointed metal objects (cutlery or utensils) into the slots in the appliance. • Switch off the appliance immediately after use. • DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THE APPLIANCE. • DO NOT USE AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILST IT IS IN USE. • DO NOT MODIFY THIS APPLIANCE.
Instructions • Racks and trays should be inserted as far as they will go into the side guides. The mechanical safety locks that prevent them from being removed must face downwards and towards the back of the oven cavity. • Do not use steam jets to clean the appliance. • Do not spray any spray products near the appliance. • (on some models only) Before starting the pyrolytic cycle, remove any food residues or large spills from previous cooking operations from the inside of the oven.
• Avoid exerting too much pressure on the oven door when open. • Do not use the handle to lift or move the appliance. Installation and maintenance • THIS APPLIANCE MUST NOT BE INSTALLED IN BOATS OR CARAVANS. • The appliance must not be installed on a pedestal. • Position the appliance into the cabinet cut-out with the help of a second person. • To avoid potential overheating, the appliance must not be installed behind a decorative door or a panel.
Instructions For this appliance • Ensure that the appliance is switched off before replacing the bulb. • Do not rest any weight or sit on the open door of the appliance. • Take care that no objects are stuck in the doors. • Do not install / use the appliance outdoors. • Only use the temperature probe provided or recommended by the manufacturer. 1.
Instructions This appliance conforms to the WEEE European directive (2012/ 19/EU) and must be disposed of separately from other waste at the end of its service life. The appliance does not contain substances in quantities sufficient to be considered hazardous to health and the environment, in accordance with current European directives. To dispose of the appliance: • Cut the power cable and remove it. Power voltage Danger of electrocution • Disconnect the mains power supply. • Unplug the appliance.
Instructions 1.7 How to read the user manual 1.8 To save energy This user manual uses the following reading conventions: • Only preheat the appliance if the recipe requires you to do so. • Unless otherwise indicated on the package, defrost frozen foods before placing them in the oven. • When cooking several types of food it is recommended to cook the foods one after the other to make the best use of the already hot oven. • Use dark metal moulds: They help to absorb the heat better.
Description 2 Description EN 2.
Description 2.2 Control panel 1 Function knob 3 Select knob This knob can be used to: • Turn the appliance on and off • Select a function. This knob can be used to set: • The cooking temperature • The duration of a function • Programmed cooking procedures • The current time • Temporarily start or stop a function. Turn the Function knob to terminate any cooking operation immediately.
2.3 Other parts Shelves Interior lighting The appliance features shelves to position trays and racks at different heights. The insertion heights are indicated from the bottom upwards (see 2.1 General description). The appliance’s interior lighting comes on: • When the door is opened. • When any function, apart from the ECO , Pyrolytic and Vapor Clean functions are selected (depending on the model). 2.
Description Oven tray (on some models only) Useful for collecting fat from foods placed on the rack above and for cooking sweets, biscuits, etc. Deep tray Self-cleaning panels (on some models only) Useful for absorbing small grease residues. Some models are not provided with all accessories. The oven accessories intended to come into contact with food are made of materials that comply with the provisions of current legislation.
Use Instructions High temperature inside the oven during use Danger of burns • Keep the oven door closed during cooking. • Protect your hands by wearing oven gloves when moving food inside the oven. • Do not touch the heating elements inside the oven. • Do not pour water directly onto very hot trays. • Do not allow children to approach the oven when it is in operation. High temperature inside the oven during use Danger of fire or explosion • Do not spray any spray products near the appliance.
Use 3.1 Using the accessories Racks and trays Tray rack Racks and trays have to be inserted into the side guides until they come to a complete stop. • The mechanical safety locks that prevent the rack from being removed accidentally must face downwards and towards the back of the oven. The tray rack has to be inserted into the tray. In this way fat can be collected separately from the food which is being cooked. Gently insert racks and trays into the oven until they come to a stop.
3.2 Using the oven First use Display When using the appliance for the first time or after a prolonged power failure, will flash on the display. In order to start a cooking function, the current time has to be set. The parameters and values for the currently selected function will be indicated on the display. To use it, simply turn the Function and Select knobs to select the values displayed. 1. Turn the Select knob current time. to select the 2.
Use Timer End Timer This function only activates the buzzer when the countdown ends. 1. When the Function knob is on position 0, press the Select knob Digits . appear on the display and the Timer indicator light flashes. 2. Turn the Select knob within 3 seconds to set the duration of the Timer (from 1 minute to 13 hours). 3. Wait 3 seconds or press the Select knob to start the Timer. During this function, the display will be dimmed 2 minutes after the knobs were last used. 4.
Use 1. Turn the Function knob to the right or left to select the required function (e.g. “FAN ASSISTED ”). 2. Turn the Select knob to the right or left to select the required temperature (e.g. “200°C”). 3. Wait 3 seconds to start cooking or press the Select knob to enter settings for the cooking duration or the end of cooking time. Pre-heating stage Cooking is preceded by a preheating stage, which allows the appliance to heat to the cooking temperature more quickly.
Use Timed Cooking Timed cooking is the function which allows you to start cooking and end it after a specific length of time set by the user. If Timed cooking is activated, it cancels any minute minder timer that may have been set previously. 1. After having selected a cooking function and a temperature, press the Select knob Digits Timed cooking does not take preheating times into account. End of timed cooking 4.
Use This function only activates the buzzer, without stopping cooking. It is not possible to set a Timer during cooking if Timed cooking has previously been selected. 1. After having selected a cooking function and a temperature, press the Select knob Digits twice. appear on the display and the Timer indicator light flashes. Timer end during cooking 4. Wait for the buzzer to indicate that the time has finished. Digits light and the Timer indicator flash. 5.
Use Programmed Cooking Programmed Cooking is the function that allows Timed Cooking to be stopped automatically at a time set by the user, after which the appliance will switch off automatically. For safety reasons, it is not possible to set the end of cooking time by itself without setting the cooking duration. 3. Press the Select knob Digits . appear on the display and the End of Cooking indicator lights flash. and Clock 4.
Use Programmed Cooking End At the end of cooking, flashes on the display and a buzzer will sound that can be deactivated by opening the door or pressing/turning one of the two knobs. How to clear Programmed Cooking 1. Press the Select knob The Cooking indicator light the display. . flashes on 2. Turn the Select knob clockwise or anticlockwise within 3 seconds to set a new Timed Cooking. Programmed Cooking has now been cleared. Cooking can be interrupted at any time by turning the Function knob to 0.
Use BOTTOM The heat comes from the bottom of the cavity. Perfect for cakes, pies, tarts and pizzas. CIRCULAIRE + BOTTOM Allows you to quickly finish cooking food that is already cooked on the surface but not internally. Ideal for quiches, suitable for all kinds of dishes. ECO Low energy cooking: this function is particularly suitable for cooking on a single shelf with low energy consumption. It is recommended for all types of food except those that may produce a large amount of moisture (e.g. vegetables).
Use • Cooking times vary according to the thickness and quality of the food and to consumer taste. • Use a meat thermometer when roasting meat, or simply press on the roast with a spoon. If it is hard, it is ready; if not, it needs to be cooked for a few more minutes. • For meat and potatoes, it is recommended to turn and / or mix the food from time to time in order to obtain a uniform browning on all sides.
Use Cooking information table Food Lasagne Pasta bake Weight (Kg) Function Shelf Temperature (°C) Time (minutes) 3-4 3-4 Static Static 1 1 220 - 230 220 - 230 45 - 50 45 - 50 Turbo/Fan assisted Turbo/Fan assisted Fan with grill Turbo/Fan assisted Circulaire/Fan assisted Turbo/Fan assisted Turbo/Fan assisted Turbo/Fan assisted 2 2 4 2 2 2 2 2 180 - 190 180 - 190 280 200 180 - 190 180 - 190 180 - 190 180 - 190 Veal roast 2 Pork loin 2 Sausages 1.5 Roast beef 1 Roast rabbit 1.
Use 3.4 Special functions Defrost 1. Place the food inside the oven. 2. Turn the Function knob until the following appears on the display. EN This function allows you to defrost food on the basis of a selectable time. 5. Turn the Select knob to set the Defrost duration (from 1 minute to 13 hours) (for example “01:30”). 6. Wait 3 seconds or press the Select knob 3. Press the Select knob to confirm that you wish to use the Special functions. The Defrost function screen appears on the display. 4.
Use Proving For successful proving, a container of water should be placed in the bottom of the oven. 4. Turn the Select knob Proving function. to select the 1. Position the dough to prove on the second level. 2. Turn the Function knob until the following appears on the display. 5. Press the Select knob to confirm the Proving function. 6. Wait 3 seconds to start the function, or press the Select knob to enter the settings for the function duration, end time etc. 3.
Use This function results in the appliance operating in a particular way: • Cooking can proceed indefinitely, it is not possible to set any cooking duration. • No preheating will be performed. • The cooking temperature which can be selected varies between 60-100 °C. • Oven light disabled, any operation such as opening the door (where present) or manual activation with the knob will not activate the light. • The internal fan remains turned off. • Knob illumination and audible prompts remain disabled.
Use 6. Turn the Select knob to select the required temperature (from 60°C to 100°C) (for example “90°C”). 7. Wait 3 seconds before starting the function. The Defrost function screen appears on the display. 3. Turn the Select knob PIZZA function. 8. Turn the Function knob from the function. to select the to 0 to exit For the Vapor Clean and Pyrolytic functions (depending on the model) see “4 Cleaning and maintenance”. PIZZA function Function designed for cooking pizza.
Use 3.5 Settings Current time 4. Turn the Select knob current time. to select the EN 1. Turn the Function knob until the following appears on the display. 5. Press the Select knob to set the hours and go to the minutes. 2. Press the Select knob to access the list of Settings. The Current time function screen appears on the display. 6. Turn the Select knob minutes. to select the 3. Press the Select knob to adjust the Current Time (for example “12:30”). 7. Press the Select knob setting the time.
Use Controls lock (Child Safety) This mode allows the appliance to lock the controls automatically after one minute of normal operation without any intervention from the user. 1. Turn the Function knob until the following appears on the display. 5. Turn the Select knob Controls lock function. to activate the 6. Press the Select knob to confirm. 7. Turn the Select knob new Setting. 2. Press the Select knob to access the list of Settings. The Current time function screen appears on the display. 3.
Use This mode allows the appliance to deactivate all heating elements, while keeping the control panel active. 4. Press the Select knob to confirm. 5. Turn the Select knob Showroom function. to activate the 6. Press the Select knob to confirm. EN Showroom (for exhibitors only) 1. Turn the Function knob until the following appears on the display. 7. Turn the Select knob new Setting. 2. Press the Select knob to access the list of Settings. The Current time function screen appears on the display.
Use Keep Warm This mode allows the appliance to keep cooked food warm (at low temperatures) after cooking finishes with a cooking cycle for which a duration has been set (if this is not manually interrupted), without altering the taste and smell obtained during cooking. 1. Turn the Function knob until the following appears on the display. 2. Press the Select knob to access the list of Settings. The Current time function screen appears on the display. 3. Turn the Select knob Keep warm function.
4 Cleaning and maintenance Food stains or residues Instructions Do not use steel sponges and sharp scrapers as they will damage the surface. Use normal, non-abrasive products and a wooden or plastic tool, if necessary. Rinse thoroughly and dry with a soft cloth or a microfibre cloth. Do not allow residues of sugary foods (such as jam) to set inside the oven. If left to set for too long, they might damage the enamel lining of the oven.
Cleaning and maintenance 2. Grasp the door on both sides with both hands, lift it so that it forms an angle of around 30° and remove it. Cleaning the door glazing The glass in the door should always be kept thoroughly clean. Use absorbent kitchen roll. In case of stubborn dirt, wash with a damp sponge and an ordinary detergent. We recommend the use of cleaning products distributed by the manufacturer. Removing the internal glass panes 3.
3. Some models have an intermediate glass pane. Remove the intermediate glass pane by lifting it upwards. 5. Refit the panes in the reverse order in which they were removed. 6. Reposition the internal glass pane. Take care to centre and insert the 4 pins into their housings in the oven door by applying slight pressure. 4. Clean the external glass pane and the panes removed previously. Use absorbent kitchen roll. In case of stubborn dirt, wash with a damp sponge and neutral detergent.
Cleaning and maintenance 4.3 Cleaning the oven cavity Drying In order to keep your oven in the best possible condition, clean it regularly after letting it cool down. Avoid letting food residue dry inside the oven cavity, as this could damage the enamel. Take out all removable parts before cleaning. For easier cleaning, we recommend removing: • The door • The rack/tray support frames • The oven seal. Cooking food generates moisture inside the appliance.
Cleaning and maintenance Removing the rack/tray support frames enables the sides to be cleaned more easily. This operation should be performed each time the automatic cleaning cycle is used (on some models only). To remove the rack/tray support frames: 1. Pull the frame towards the inside of the oven cavity to unhook it from groove A. 2. Then slide it out of the seats at the back B. 3. When cleaning is complete, repeat the above procedures to put the rack/tray support frames back in.
Cleaning and maintenance Regeneration of self-cleaning panels (catalytic cycle) (on some models only) The regeneration cycle of the self-cleaning panels is a cleaning method through heating suitable for removing small grease residues, not sugar-based ones. 1. Clean the base and the upper guard first (where fitted) with a microfibre cloth soaked in water and neutral washing up liquid. Rinse thoroughly. 2. Set a regeneration cycle by selecting a fan assisted function at the maximum temperature for one hour.
Cleaning and maintenance 4.4 Vapor Clean (on some models only) Improper use Risk of damage to surfaces • Remove any food residues or large spills from previous cooking operations from the inside of the oven. • Carry out assisted oven cleaning operations only when the oven is cold. EN The Vapor Clean function is an assisted cleaning procedure that facilitates the removal of dirt. Thanks to this process, it is possible to clean the inside of the oven very easily.
Cleaning and maintenance Vapor Clean cycle setting If the internal temperature is greater than the one required, the function will be stopped immediately and the following message appears on the display: 3. Turn the Select knob Vapor Clean function. to select the 4. Press the Select knob Vapor Clean function. to confirm the Let the appliance cool down before activating the function. 1. Turn the Function knob until the following appears on the display.
Cleaning and maintenance 7. Turn the Function knob from the function. to 0 to exit Programmed Vapor Clean cycle It is possible to program the Vapor Clean function start time, like all other cooking functions. 1. After having selected the Vapor Clean function, turn the Select knob (the End of cooking indicator light turns on) to set the time at which you want the Vapor Clean function to end. 2. Wait 3 seconds before confirming the settings.
Cleaning and maintenance 4.5 Pyrolytic function (on some models only) Pyrolytic cleaning is an automatic high-temperature cleaning procedure that causes dirt to dissolve. Thanks to this process, it is possible to clean the inside of the oven very easily. Improper use Risk of injury • When this function is in use, the surfaces could reach temperatures that are higher than usual. • Keep children at a safe distance. • Completely remove all accessories from inside the oven.
Cleaning and maintenance The duration of the Pyrolytic cycle appears on the display (factory set to 2 hours). 4. Turn the Select knob to set the duration of the Pyrolytic cycle from a minimum of 2 hours to maximum of 3 hours. Recommended pyrolytic cycle duration: • Light dirt: L01 - 02:00. • Medium dirt: L02 - 02:30. • Heavy dirt: L03 - 03:00. 5. Press the Select knob to confirm the parameters. 6. Wait 3 seconds before starting the function. Pyrolytic cycle 7.
Cleaning and maintenance Setting of a programmed Pyrolytic cycle During the Pyrolytic cycle, the fans produce a more intense noise due to a greater rotation speed. This is an absolutely normal operation, intended to provide more effective heat dispersal. At the end of the Pyrolytic cycle, the fans will continue to operate for long enough to prevent overheating the walls of adjacent units and the front of the oven.
Cleaning and maintenance 4.6 Extraordinary maintenance 5. Turn the Select knob (the End of Cooking Indicator light turns on) to set the time at which you want the Pyrolytic cycle to end. 6. Wait 3 seconds before confirming the settings. 7. The appliance waits until the set start time to start the Pyrolytic cycle. It is not possible to select any function once the door lock device has been activated. It is anyway possible to switch off the appliance by moving the Function Knob to 0.
Cleaning and maintenance Replacing the internal light bulb 4. Slide out and remove the light bulb. Live parts Danger of electrocution • Unplug the appliance. • Use protective gloves. 1. Completely remove all accessories from inside the oven. 2. Remove the rack/tray support frames. 3. Use a tool (e.g. a spoon) to remove the bulb cover. Pay attention not to scratch the oven cavity enamel. Do not touch the halogen light bulb directly with your fingers, but wrap it in insulating material. 5.
5 Installation Connection with plug and socket 5.1 Electrical connection Make sure that the plug and socket are of the same type. Avoid using adapters and shunts as these could cause overheating and a risk of burns. Fixed connection Fit the power line with an all-pole circuit breaker with a contact separation distance sufficient to provide complete disconnection in category III overvoltage conditions, pursuant to installation regulations.
Installation 5.2 Positioning Position of the power cable Heavy appliance Crushing hazard • Position the appliance into the cabinet cut-out with the help of a second person. Pressure on the open door Risk of damage to the appliance • Never use the oven door to lever the appliance into place when fitting. • Avoid exerting too much pressure on the oven door when open. Heat production during appliance operation Risk of fire • Check that the carcase material is heat resistant.
Installation Fastening bushings Appliance overall dimensions (mm) EN 1. Remove the bushing covers on the front of the appliance. 2. Mount the appliance into the recess. 3. Secure the appliance to the carcase using the screws. 4. Cover the bushings with the previously removed covers.
Installation Mounting under worktops (mm) Make sure that there is a space of approx. 60 mm at the back / bottom of the unit.
Installation Mounting under worktops (pyrolytic models only) EN Whenever a hob is installed above the oven, a wooden separator should be installed at a minimum distance of 10 mm from the top of the oven to prevent overheating when the two appliances are used at the same time. It must only be possible to remove the separator by using suitable tools.
Installation Mounting into a column (mm) Make sure that there is a space approx. 35-40 mm deep at the top / back of the unit.