ELECTRONIC OVENS EN INSTALLATION INSTRUCTIONS FOURS ELECTRONIQUES FR INSTRUCTIONS D’INSTALLATION HORNOS ELECTRÓNICOS ES INSTRUCCIONES PARA LA INSTALACIÓN
EN TABLE OF CONTENTS PAGE Introduction 2 Tools you will need 2 Power requirements 2 Choosing oven location 2 Steps for installation 2 Installation notes 3 Electrical supply 7 Wiring requirements 7 Connecting to 208 volt circuit 8 Electrical connections 9 3-Wire branch circuit (for US only) 9 4-Wire branch circuit (for US and Canada) 9 Final checklist WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal
EN Installation Instructions Introduction Power requirements Please read these instructions COMPLETELY AND CAREFULLY. They will save you time and effort and help to ensure optimum oven performance. Be sure to observe all WARNINGS. These installation instructions are intended for use by a qualified installer. In addition to these instructions, the oven shall be installed: The oven must be supplied with the proper voltage and frequency.
Installation Instructions TECHNICAL DATA For cutout dimensions see following section titled: Preparing location SINGLE OVEN F7SP30*1 DOUBLE OVEN UPPER CAVITY LOWER CAVITY F7DP30*1 EN Electrical Ratings and Maximum Connected Load @ 120/240 Volts 60 Hz Amperes kW @ 120/208 Volts 60 Hz Amperes kW 15.4 3.70 16.8 3.50 Amperes kW Amperes kW 31.2 7.50 30.3 6.30 Installation notes 1. Do not slide oven across floor. Damage to floor covering or floor could result. 2.
EN Installation Instructions WALL OR UNDER COUNTER INSTALLATION, SINGLE OVEN Secure oven to cabinet using the screws provided. Screws should be inserted through the mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not over tighten screws. F B Electrical supply junction box A C B C E D E A Electrical supply junction box WALL INSTALLATION, DOUBLE OVEN Secure oven to cabinet using the screws provided.
Installation Instructions EN FLUSH INSTALLATION Mounting strip H Mounting strip F G F G Finished sides (same finish like the cabinet) Finished sides (same finish like the cabinet) Ltr. DIMENSION F G H Cutout Width Cutout Height Visible part of the mounting strips SINGLE 30” 30 1/16” 28 1/32” 3/4” DOUBLE 30” (76.4 cm) 30 1/16” (71.2 cm) 51” ( 1.9 cm) 3/4” ( 76.4 cm) (129.5 cm) ( 1.
EN Installation Instructions PRODUCT-DIMENSIONS 26 3/4” (68 3/4” cm) 26 (68 cm) 26 3/4” (68 3/4” cm) 26 (68 cm) 50 3/4” (129 cm) 50 3/4” (129 cm) 27 7/8” (70.7 cm) 27 7/8” (70.7 cm) 29 3/4” (75.4 cm) 29 3/4” (75.4 cm) 29 3/4” (75.4cm) 29 3/4” (75.4cm) 1” (2.5 1”cm) (2.5 cm) 3/4” (23/4” cm) (2 cm) 7 7/8” (20 cm) 7 7/8” (20 cm) 1” (2.51”cm) (2.5 cm) 27 1/8” (69 1/8” cm) 27 (69 cm) 6 3/4” (23/4” cm) (2 cm) 7 7/8” (20 cm) 7 7/8” (20 cm) 17” (4317” cm) (43 cm) 23 1/8” (58.7 cm) 23 1/8” (58.
Installation Instructions Electrical supply Wiring requirements Before installing the oven have a qualified electrician verify that your home is provided with adequate electrical service and that the addition of the oven will not overload the branch circuit on which it is to be installed. A separate three-wire or four-wire single phase, 240 Volt, 60 Hz, or a 208 Volt, 60Hz branch circuit is required. When making the wire connections, use the entire length of the conduit provided (3 feet).
EN Installation Instructions Connecting to 208 volt circuit This option is provided for areas where standard 240 Volt service is not available. This option must be accessed with the oven connected to power source, and using the following sequence: ELECTRICAL SHOCK HAZARD a) Press the SET key and select the option by means of the arrow and confirm with the START key. • The electrical power to the oven branch circuit must be shut off while line connections are being made.
Installation Instructions EN Electrical connections Be sure your appliance is properly installed and grounded by a qualified technician. Ask your dealer to recommend a qualified technician or an authorized repair service. This appliance is manufactured with a green GROUND wire connected to the oven chassis. After making sure that the power has been turned off, connect the flexible conduit from the oven to the junction box using a U.L. listed conduit connector.
EN Installation Instructions Final checklist To prevent improper connections leading to damage of electrical components and so voiding the warranty, the following steps must be performed: 1. Check the electrical requirements and make sure you have the correct electrical supply and that the oven is properly grounded. 2. Turn on the power supply to the oven. 3. Check power at the junction box wires using a voltmeter having a range of 0-250 VAC.
Note / Note / Nota 11
Note / Note / Nota 12
DOC COD.
