Conversion Instructions

ManualsBrandsSmeg ManualsAppliancesSmeg 36" Victoria White Free-Standing All-Gas Range

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

WARNING: If the instructions contained in this manual are not followed

precisely, fire or explosion may result causing property damage, personal

injury or loss of life.

• Do not store or use gasoline or other flammable vapors or liquids near

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switches.

• Do not use any telephones in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer,

service company or gas supplier.

READ AND SAVE THESE INSTRUCTIONS - Your safety and the safety of

others are very important.

We have provided many important safety messages throughout this manual and

on the appliance.

Read all the instructions before using the appliance and always obey all safety

messages.

RECOGNIZE SAFETY INFORMATION

This is a safety alert symbol. This symbol alerts you to potential hazards that can

result in severe personal injury or loss of life.

UNDERSTAND SIGNAL WORDS

A signal word - DANGER, WARNING or CAUTION - is used with the safety alert

symbol. DANGER denotes the most serious hazards. It means you could lose your

life or be seriously injured if you do not immediately follow the instructions.

WARNING means you could lose your life or be seriously injured if the instructions

are not followed. CAUTION indicates a potentially hazardous situation which, if

not avoided, could result in minor to moderate injury.

Summary of content (10 pages)

PAGE 1
Important Safety Instructions EN IMPORTANT SAFETY INSTRUCTIONS WARNING: If the instructions contained in this manual are not followed precisely, fire or explosion may result causing property damage, personal injury or loss of life. • Do not store or use gasoline or other flammable vapors or liquids near this or any other appliance. WHAT TO DO IF YOU SMELL GAS • • • • Do not try to light any appliance. Do not touch any electrical switches. Do not use any telephones in your building.
PAGE 2
Important Safety Instructions The safety messages will inform you of potential hazards, on how to avoid the risk of injury and what can occur if the instructions are not followed. IMPORTANT: Observe all codes and ordinances in force. WARNING: For your safety, the instructions contained in this manual must be followed to minimize the risk of fire or explosion and to prevent property damage, personal injury or loss of life.
PAGE 3
Conversion Kit This conversion kit consists of the following components: EN 1 List of components • One warning label change injectors • One label for LPG injectors • Two seal gaskets 12.5x18.5x2 (mm). • One injector Ø 0.60 mm for the Auxiliary burners. • Two injectors Ø 0.80 mm for the Semi-rapid burners. • One injector Ø 0.98 mm for the Rapid burner. • One injector Ø 0.54 mm for the Ultrarapid Dual burner (internal crown). • One injector Ø 1.10 mm for the Ultrarapid Dual burner (external crown).
PAGE 4
Conversion Kit 2 Gas connection 3 Adaptation to different types of gas Check that the main gas supply line to the range is shut off and that the power supply cord is disconnected. To adapt the regulator to the type of gas used, the following must be done: 1. Unscrew the cover of the pressure regulator. 2. Unscrew the spring retainer from the cover. 3. Screw the spring retainer back on according to the type of gas used (see the following illustrations). • Natural Gas: Set pressure to 5” W.C.P.
PAGE 5
Conversion Kit 3. Replace the nozzles according to the type of gas to be used and the description in section 3.2 “Burner and nozzle characteristics table”. EN • Incoming line pressure upstream from the regulator must be 1” (2.5 cm) W.C.P. higher than the manifold pressure in order to check the regulator.
PAGE 6
Conversion Kit 5 Replacing the oven burner nozzle 1. Open the oven door and remove all of the accessories from inside the oven. 2. Remove the shelf. 5. Replace the nozzle using a 7 mm socket wrench; install the most suitable one for the type of gas used. 3. Remove the oven burner fastening screws from the base. The tightening torque of the nozzle must be 4 Nm. 4. Lift the burner at the side and pull it towards you to remove it from its seat. 6.
PAGE 7
6 Replacing the gas grill nozzle 1. Open the door and remove all accessories inside the oven. 2. Loosen the screws fastening the gas burner with grill to the upper part of the oven. 4. Replace the nozzle with the most suitable one for the type of gas used using a 7 mm socket wrench. 3. Push the burner until the nozzle is accessible. The tightening torque of the nozzle must be 4 Nm. 5. After having replaced the nozzle, put the burner back in its seat.
PAGE 8
Conversion Kit 7 Test the appliance 8 Minimum adjustment Follow these instructions to leak test the appliance: Use a brush and liquid detergent to test all gas connections for leaks. Bubbles around connections indicate a leak. If a leak appears, shut off the gas valve controls and adjust the connections. Then check the connections again. Remove all the detergent product from the range. Replace the parts on the burner and turn the knobs on the gas tap valves.
PAGE 9
Conversion Kit EN 9 Burner and nozzle characteristics tables To adjust the range for LP gas or to return to Natural Gas use, refer to the charts below. Natural Gas QT (BTU) Injector Ø (mm) QR (BTU) LP QT (BTU) Injector Ø (mm) QR (BTU) By-pass (mm) AUX SR R 4500 0.90 1200 AUX 8000 1.20 1600 SR 12000 1.52 2400 R 4200 0.60 1200 0.33 7500 0.80 1600 0.39 11000 0.98 2400 0.45 DUAL int DUAL est Oven 4000 16000 17000 0.90 1.75 180 800 4200 DUAL int DUAL est Oven 3500 14500 17000 0.54 1.
PAGE 10
Conversion Kit 10 Combustion products Air The combustion products may be extracted by means of hoods connected to a natural draught chimney whose efficiency is certain or via forced extraction. An efficient extraction system requires precision planning by a specialist qualified in this area and must comply with the positions and distances indicated by the applicable standards. When the job is complete, the installer must issue a certificate of conformity.